Re: 59 Apache/C6 Corvette build
5 Attachment(s)
Here we go. Getting busy on this project again. Bed mounted and fenders widened. Step is a little work.
|
Re: 59 Apache/C6 Corvette build
Nice job on the fenders...it looks stock
Marc |
Re: 59 Apache/C6 Corvette build
We added 1.5" and it looks very stock to the naked eye. I needed the room for the factory offset Corvette wheel. I was able to get a p355 tire on the 19x12.
|
Re: 59 Apache/C6 Corvette build
Wow, that fender work is phenomenal!
|
Re: 59 Apache/C6 Corvette build
beautiful fab!
|
Re: 59 Apache/C6 Corvette build
1 Attachment(s)
Here is a pic looking back. Hard to tell it's 1.5" wider.
|
Re: 59 Apache/C6 Corvette build
1 Attachment(s)
Getting bed floor situated. Need a 4" floor lift and decided to have a tilt up floor.
I had my old tailgate and thought the script would look good on the back of the floor lift. |
Re: 59 Apache/C6 Corvette build
Nice detail on the rear bed sill. Looking good..
Marc |
Re: 59 Apache/C6 Corvette build
where did you get your tailgate release from ????? first time i see one like that awsome
|
Re: 59 Apache/C6 Corvette build
Mar-k. Very nice quality. The whole bed is from them.
The tailgate has two bear claw latches and works smooth. |
Re: 59 Apache/C6 Corvette build
2 Attachment(s)
Bed floor coming together.
|
Re: 59 Apache/C6 Corvette build
beautiful fab work sir!
|
Re: 59 Apache/C6 Corvette build
Looks great! is that bed tilt setup a kit or did you fab that? I just ordered a couple "bed tonneau cover" gas struts and a couple ball mounts... not sure if its going to work until Mr Amazon drops it off
|
Re: 59 Apache/C6 Corvette build
It's not a kit. We are building a design we laid out on paper with Camaro trunk hinges and an electric assisted bear claw latch. The rest is 1" square tubing. The bed wood will attach with Mar-k strips and some threaded wood inserts from the underside. I didn't want to use the L strip on the bed sides. I wanted to have the wood bump up to the sides with no carriage bolts.
|
Re: 59 Apache/C6 Corvette build
5 Attachment(s)
Tilt bed framing done and working. I have several rubber adjusters in several places that keep all squeeks away.
|
Re: 59 Apache/C6 Corvette build
Truck is looking great! Your fab work is top notch!
|
Re: 59 Apache/C6 Corvette build
Thanks, Moving on to do the wood in the bed next.
|
Re: 59 Apache/C6 Corvette build
Wow, amazing work!!!
|
Re: 59 Apache/C6 Corvette build
meaty! :haha:
|
Re: 59 Apache/C6 Corvette build
2 Attachment(s)
Bed floor dialed in and done. Ready for wood. Added 60lb gas struts to lift and keep from lifting all the way up. Quick disconnects make lifting all the way up easy. I kept the gas helpers on the hinge, they keep it straight up when I remove the long struts.
|
Re: 59 Apache/C6 Corvette build
Quote:
|
Re: 59 Apache/C6 Corvette build
Nice job on the tilt bed floor!
:uhmk: |
Re: 59 Apache/C6 Corvette build
I just read back through this entire thread and all I can say is "WOW". And that 55 Plymouth grill looks right at home in this truck.
|
Re: 59 Apache/C6 Corvette build
4 Attachment(s)
Update
|
Re: 59 Apache/C6 Corvette build
Looking good!
|
All times are GMT -4. The time now is 11:11 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com