The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=4)
-   -   Restoring Rusty (https://67-72chevytrucks.com/vboard/showthread.php?t=645440)

rich weyand 06-11-2016 01:42 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 7621810)
dudes tell me going roller gives you 20 more horse power with a slide of your credit card! LOL plus you aint gotta play the Zinc oil additives game

Just trying to hold down the wear and tear on the credit card.

Zinc additive is $5 per oil change. Not a biggie.

On the connecting rod bearing, yeah, I would go a couple thousandths over.

Jake Wade 06-11-2016 03:15 PM

Re: Restoring Rusty
 
They make .001 bearings as well as .002. See if your local parts store has some plastigauge so you can check things out, I would rather be a tad loose than too tight.

The bearings do not appear to be worn much. When you see copper, they are worn.

Gregski 06-11-2016 04:12 PM

Re: Restoring Rusty
 
1 Attachment(s)
Quote:

Originally Posted by rich weyand (Post 7621816)
Zinc additive is $5 per oil change. Not a biggie.

not arguing with you, but not in California here's a pic I took for you at our local NAPA store today, so with tax and license you're looking at $20 bucks out the door

Gregski 06-11-2016 04:14 PM

Re: Restoring Rusty
 
1 Attachment(s)
Quote:

Originally Posted by Jake Wade (Post 7621909)
... The bearings do not appear to be worn much. When you see copper, they are worn.

I concur, here's what the con rod looked like

Gregski 06-11-2016 04:16 PM

Re: Restoring Rusty
 
5 Attachment(s)
went ahead and bought just a standard size bearing, for like $4.00 bucks

man where will I get my bearings when Trump builds that wall (kidding folks, don't get all political on me, let's just make this truck great again!)

Gregski 06-11-2016 04:21 PM

Re: Restoring Rusty
 
2 Attachment(s)
you know the drill, time for a stare and compare

old bearing and new bearing

[mini rant] I don't know about you, but I struggle to view these things as bearings, to me a bearing has balls in it, you know what I'm saying, these there things are like shims to me, I just can't wrap my small mind around the concept thats all [/mini rant]

rusty76 06-11-2016 04:44 PM

Re: Restoring Rusty
 
That really sucks. I hope replacing the bearing helps. Seems I've never heard my old truck not tick somewhere. Lol. My toaster(daily) is just too quiet. But it does have AC.

Gregski 06-11-2016 06:57 PM

Re: Restoring Rusty
 
well, so I replaced the #4 con rod bearing, did that make the engine ticking noise go away?

NO

my goodness, what is up with Rusty? so I parked it on the street and started drinkin'

Jake Wade 06-11-2016 07:11 PM

Re: Restoring Rusty
 
Keep in mind the cam turns at half the speed as the crank so a piston or rod noise would be twice as fast as a valvetrain related noise.

rich weyand 06-11-2016 07:30 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 7621961)
not arguing with you, but not in California here's a pic I took for you at our local NAPA store today, so with tax and license you're looking at $20 bucks out the door

Yeah, but to get your zinc (ZDDP, actually) up to where it needs to be, you only need to use four ounces. ZDDPPlus is $10/bottle on Amazon, and you only use half a bottle per change. Too much is not good either.

peabobble 06-11-2016 09:14 PM

Re: Restoring Rusty
 
Wrist pins maybe?

SkinnyG 06-11-2016 10:49 PM

Re: Restoring Rusty
 
Did you Plastigage #4? That would have been a quick way to rule out or condemn the rod bearing.

I still maintain it's a piston problem; I'm with peabobble.

Gregski 06-12-2016 12:41 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by peabobble (Post 7622196)
Wrist pins maybe?

I tried to check those, all I got was the con rod was able to slide side to side on the wrist pin a bit, but it did not have any up and down play, as good as I could tell with it being in the truck

Gregski 06-12-2016 12:43 AM

Re: Restoring Rusty
 
Gentlemen, could it still be the exhaust header even if the noise goes away when I unplug the spark plug wire on #4?

I am tempted to pull the headers off (at least on that side) and bolt up my old manifolds and see what that does, but if you think its a waste of time knowing that there is no noise with #4 plug disconnected than let me know.

SkinnyG 06-12-2016 12:45 AM

Re: Restoring Rusty
 
You won't likely feel any up and down play - you need the piston out, and try to rock them.... um... like, rock the piston down while you rock the con rod up - kind of feeling if the wrist pin hole is elongated.

Assuming a piston skirt or ring isn't broken.

SkinnyG 06-12-2016 12:47 AM

Re: Restoring Rusty
 
Oh. Exhaust leak....... Interesting.

Can you give a listen with a stethoscope or long screwdriver, and see if the sound is coming from the BLOCK, or from the HEADER TUBE.

Sometimes header tubes make a ticking sound, just the speed of the gasses hitting the corner of the tube or something.

Gregski 06-12-2016 01:29 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by SkinnyG (Post 7622418)
Can you give a listen with a stethoscope or long screwdriver, and see if the sound is coming from the BLOCK, or from the HEADER TUBE.

I tried that with both a stethoscope and a long screw driver, and a rubber hose, and my buddies tried it and none of us can pin point where the sound is coming from. I even got under the truck and tried to listen to it from there, still can't tell.

The stethoscope and the long screw driver let us hear the internals of the engine but thats not the ticking sound, also there is no tapping sound from the distributor, no sound from the fuel pump, no sound from the starter, no sound from the exhaust manifold, its so bizarre

actually drove the truck with #4 spark plug unplugged to show my buddy and man the truck sounds so smooth without it, I just wish I had a V8 and not a V7, lol

Gregski 06-12-2016 01:37 AM

Re: Restoring Rusty
 
well seems like this dude on YouTube has the same problem, and of course the video is abandoned and we don't know what it was or how he fixed it

Piston Slap, Spun Bearings, Valve Lash, Engine Noise Diagnostics

02 Engine Noise Diagnostics

Gregski 06-12-2016 01:54 AM

Re: Restoring Rusty
 
Man I wish I tested my pistons like this guy is doing in this video when I had my engine out and the cylinder heads out, check it out and tell me what you think

5.3 LM7 Piston Rock aka Piston Slap

hatzie 06-12-2016 02:32 AM

Re: Restoring Rusty
 
This isn't an LS motor or even a Vortec smallblock like you liberated the heads from. Tolerances were pretty loose on the earlier Gen I smallblocks.

Look in the 1974 service manual. The '70s GM engines were intended to be run on 10W40 and even 20W50 motor oil except at fairly low temperatures. The chart in the 1974 GM service manual says to run 5W30 if the outdoor temps range from less than -30°F to 60°F max. That same chart says to run 20W50 between 20°F to over 100°F.

Sacramento averages 60°F year round... For Sacramento to get below 20°F would mean the apocalypse is fast approaching.
Try swapping to a higher SAE weight oil... Running a good synthetic 20W50 should quiet her down and it will not hurt a thing to use year round. If it's a loose wrist pin it won't change a thing.

Gregski 06-12-2016 09:07 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by hatzie (Post 7622460)
This isn't an LS motor or even a Vortec smallblock like you liberated the heads from. Tolerances were pretty loose on the earlier Gen I smallblocks.

Look in the 1974 service manual. The '70s GM engines were intended to be run on 10W40 and even 20W50 motor oil except at fairly low temperatures. The chart in the 1974 GM service manual says to run 5W30 if the outdoor temps range from less than -30°F to 60°F max. That same chart says to run 20W50 between 20°F to over 100°F.

Sacramento averages 60°F year round... For Sacramento to get below 20°F would mean the apocalypse is fast approaching.
Try swapping to a higher SAE weight oil... Running a good synthetic 20W50 should quiet her down and it will not hurt a thing to use year round. If it's a loose wrist pin it won't change a thing.

ever since the engine rebuild I have been running 20W-50 engine oil with the Lucas zinc additive

yesterday we put brand new 20W-50 engine oil in with a brand new oil filter, the Lucas zinc additive and added the Lucas HEAVY DUTY oil stabilizer, our ratio is extreme for testing purposes of 2 quarts Lucas and 3 quarts oil, its really thick on purpose right now to see if it will quiet down the noise, and it does NOT

79sierra 06-12-2016 12:34 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 7622415)
Gentlemen, could it still be the exhaust header even if the noise goes away when I unplug the spark plug wire on #4?

I am tempted to pull the headers off (at least on that side) and bolt up my old manifolds and see what that does, but if you think its a waste of time knowing that there is no noise with #4 plug disconnected than let me know.

Sure, but hard to tell without hearing it. I wouldn't put the manifold back on, I would pull the header and check the gasket around #4. Double sure would be to remove the header and check it for any high or low spots with a straight edge and also check the head around that exhaust port. Hope it is not internal!

Gregski 06-12-2016 06:34 PM

Re: Restoring Rusty
 
3 Attachment(s)
Well, well, well, what do we have here?

Could that be numero quatro?

Jake Wade 06-12-2016 06:41 PM

Re: Restoring Rusty
 
You need some 1444 Felpro's

Gregski 06-12-2016 07:04 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Jake Wade (Post 7623010)
You need some 1444 Felpro's

Jake I dont think those be the crushable kind, they look similar to the ones i was runnin'

Gregski 06-12-2016 07:04 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by chaplain (Post 7623018)
b
i
n
g
o

l
o
l

SkinnyG 06-12-2016 07:13 PM

Re: Restoring Rusty
 
https://github-camo.global.ssl.fastl...61316b2e6a7067

Jake Wade 06-12-2016 07:59 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 7623031)
Jake I dont think those be the crushable kind, they look similar to the ones i was runnin'

I use them all the time. I am currently running a set on my personal truck that have been on there for three years now, and that's with cheapie flowtech headers.

They fit the Vortec exhaust ports perfectly. They are the only kind that I have used that I would recommend. They are great gaskets with metal reinforcement.

SkinnyG 06-12-2016 08:10 PM

Re: Restoring Rusty
 
I've had great success with these:

http://cdn3.volusion.com/brkc4.4tqja...jpg?1442918815

buffydores 06-12-2016 09:22 PM

Re: Restoring Rusty
 
Just finished reading the whole thing. So glad it's just a gasket. You've done such wonderful work. I can't wait for my kids to get a little older to give me some more time to work on my stuff.

Gregski 06-12-2016 09:45 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by buffydores (Post 7623166)
Just finished reading the whole thing. So glad it's just a gasket. You've done such wonderful work. I can't wait for my kids to get a little older to give me some more time to work on my stuff.

buy them an iPad and you'll have all the time in the world!!!

Gregski 06-12-2016 09:48 PM

Re: Restoring Rusty
 
2 Attachment(s)
so lets get you updated Greggie style

hello old friend

Gregski 06-12-2016 09:52 PM

Re: Restoring Rusty
 
2 Attachment(s)
the goal for today was to replace the headers with manifolds (or at least on the problem side) and although we thought we found the smoking gun (pun?) we did not want to change horses midstream sorta speak

so first we had to knock the ugly off that log

7 minutes with the death wheel and she was naked, and I'll be lying to you all if I didn't tell you that I considered grinding her nice and smooth for a minute, but then I went and got a beer instead

Gregski 06-12-2016 09:55 PM

Re: Restoring Rusty
 
1 Attachment(s)
although I went a lookin' for somethin' fancier than these trusty ol three piece Felpro gaskets I didn't find nothing better, and they've been good to me in the past

Gregski 06-12-2016 09:58 PM

Re: Restoring Rusty
 
3 Attachment(s)
On in 90 Seconds

I kid you not brothers and sisters, manifolds are sooooo easy to work with, but you already know that, so I must admit: headers are a young mens' sport.

Gregski 06-12-2016 10:01 PM

Re: Restoring Rusty
 
quit drawing this out, did going back to manifolds get rid of your engine ticking sound or not?

Hewk yeah it did, NMFT! No More Frustrating Ticking

Gregski 06-12-2016 10:07 PM

Re: Restoring Rusty
 
2 Attachment(s)
so there was no more ticking sound but the truck sure did sound funny with headers and a Flowmaster on one side and an exhaust manifold and a Turbo muffler on the other, there sure is a difference in sound between the two sides that's fer sure, and I won't tell you I may could have liked the sound on the manifold side, since I must justify my header expenditure, ha ha

so back to the parts house I went looking for some crusher gaskets, only to come away with these beauties that set me back $35 bones

how in the world they is reusable I'll never know

so did I put them on? Um no!

wait what?

I wanted to put them on, but those Felpro manifold gaskets were stuck to the enjin block and I didn't feel like scraping brand new gaskits off, then and there, so I said what the hewk lets give them a go with these them headers, and guess what they worked beautifully, SNMFT - Still No More Frustrating Ticking

so overall it was a good day, I fixed my truck, and my countrymen beat North Ireland in an Euro Cup 2016 match, what? you don't pretend to be a soccer fan every 4 years weather you need to or not?

Gregski 06-12-2016 10:11 PM

Re: Restoring Rusty
 
Wait a minute...

Houston... we have a problem!

The engine runs so smooth now I can hear the PCV valve ratlin'!!!

ha ha ha, no for real

79sierra 06-13-2016 12:07 AM

Re: Restoring Rusty
 
Good job, I bet you're exhausted!

KQQL IT 06-13-2016 12:20 AM

Re: Restoring Rusty
 
http://67-72chevytrucks.com/vboard/a...1&d=1465770796

Looks like a gasket problem, not a header problem.
Round port gaskets may have corrected that leak.


All times are GMT -4. The time now is 01:51 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com