Re: Restoring Rusty
Oh! I didn't know you were cleaning those...
Next time, try Electrolysis. Suspend the part in a tub of water and 1/4 cup Arm & Hammer washing soda. Hook the + of a battery charger to some clean scrap iron suspended in the solution. Hook the - of the battery charger to the part. Turn on the charger, and walk away. Come back later and it will be clean, gray, cast iron, ready for header paint. Quick and dirty video: https://www.youtube.com/watch?v=CqTID6rQ5JA |
Re: Restoring Rusty
I'm impressed how things clean up with mineral spirits really.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - Quick Lighting Fix
1 Attachment(s)
frustrated with poor lighting in my garage I finally came up with a quick fix
the problem was that I like to work with the garage door opened, well as you may know when the door is open it cover my florescent light bars so the light don't shine, so solution zip tie a 4 foot light to the hood, done and done |
Re: Restoring Rusty - Makes fer a quick clean up.
4 Attachment(s)
First of all, who am I to give advice, right?! lol, jk
But in case you don't like oil and grime on your (/your wives) garage floor, here's what works for me I bought one of these 3 foot wide and 50 foot long rolls of 4 mil plastic that painters use (the 4 mil is pretty thick so I like it, it don't tear like the thin ceran wrap junk) Anytime I work on the truck I roll out about 4 feet of it and use scissors to cut off a piece, then I slide it under the truck, at 3 foot wide it feels nicely between the wheels even with the car not off the ground, after I am done with the job I just fold it up and stick it in the trash |
Re: Restoring Rusty
4 Attachment(s)
New Years Day two thousand fifteen, Captains Log day 116
9:00 am 30* inside a cold dark garage... just a man in his favorite blue jeans and dirty ol' sweatshirt (ok, long johns, three T shirts underneath and two pairs of socks, geez, don't judge me - it's California in the winter) having degreased the driver side it is time to do the same on the passenger side |
Re: Restoring Rusty - Reading Exhaust Manifold Bolts
2 Attachment(s)
looking for the Bolt Whisperer?
I know you read spark plugs but I'm not sure if you can read bolts, exhaust manifold bolts for that matter anyway, if you don't own one of these magnetic chrome trays I strongly recommend one for storing all your loose nuts and bolts during the disassembly process so from the rear to the front of the cylinder head, the bolts around #8 were black and wet, the bolts around #6 & #4 were semi black and wet, and the last two bolts around #2 were dry, so what, so what does that mean? my guess oil from the rocker cover gasket area leaking and seeping down and around the exhaust manifold, but that's just a guess |
Re: Restoring Rusty - Exhaust Heat Shields
2 Attachment(s)
pics of the two heat shields from the passenger side and all four together just because
the one in the upper right hand corner I tried to clean up a bit with Mineral Spirits |
Re: Restoring Rusty - What are these for?
1 Attachment(s)
can somebody tell me what are these do dads for, other than adding a step in order to remove the exhaust manifold bolts by having to reach for a flat screw driver to bend these tabs back in order to ... wait a minute is that what these are for, to prevent the bolts from wiggling out?!
|
Re: Restoring Rusty - Passenger Side Exhaust Manifold
2 Attachment(s)
and here is what the passenger side (right side) exhaust manifold looks like
again, same as with the other side (driver side) note the pesky air tubes sticking out of the ports |
Re: Restoring Rusty - Manifold vs Header
2 Attachment(s)
here is the passenger side (right side) manifold compared to the Hedman Hedder, again I don't think this header will fit in my truck, this is just for size/shape comparison
|
Re: Restoring Rusty - Air Tubes Removed
1 Attachment(s)
and removed the air tubes out of this one as well, hope this shows you an extra step to take for those of you guys out there deleting the A.I.R. system by simply removing the outside tubes and plugging the holes with those brass plugs - I believe this will improve exhaust flow and is worth doing
|
Re: Restoring Rusty - What are these for?
Quote:
|
Re: Restoring Rusty
Looking good. So what is your method with the mineral spirits? Do you spray it on? Wipe on or another method. I'm curious. I am impressed how clean it gets things. Keep on keeping man.
|
Re: Restoring Rusty
Quote:
Step 1 - use putty knife (plastic or metal) to scrape off big pieces of gunk, dirt, or grime. Use plastic one if you don't want to scratch the paint, use metal if you plan on repainting or if the surface can handle it. Step 2 - Take paper towel fold it into a 3inch by 3 inch square and soak it with the fluid. Then unfold the towel and fold it just once and start wiping. Get the area wet, the first towel is not so much to wipe things off as it is to get the area wet. THROW DIRTY TOWEL AWAY do not reuse. Step 3 - Use brushes to loosen hard to get off dirt. You can use a spray paint cap/lid as a cup to poor some fluid in to dip your brush. You can exchange brushes for steel wool as you progress as the area gets cleaner. Step 4 - Get new paper towel, a dry one and wipe away what will come off. THROW DIRTY TOWEL AWAY do not reuse. Step 5 - Repeat 2-4 important, start in the worst part, the dirties place or the one most difficult to reach and work out of that zone, also take a break, cleaning sucks, walk away or better yet finish the job the next day or the following weekend I don't know how the pros do it, but this works for me. |
Re: Restoring Rusty
Kinda like a parts washer, without the parts washer....
|
Re: Restoring Rusty
Thanks. That helps. I've got tons of cleaning in my future.
|
Re: Restoring Rusty
Quote:
Would you mind posting the part#? |
Re: Restoring Rusty
1 Attachment(s)
Quote:
FTA 9203 Semi Flat Black http://www.krylon.com/products/rust-...tative-enamel/ |
Re: Restoring Rusty - Its Fender Time
5 Attachment(s)
got this 20% Off on All Fenders ad in the mail from our local Pick n Pull junk yard so I had no choice but to go pull one
with tax ($4.73), an environmental fee ($4.24), and some BS core charge ($4.99) it came out to be just under $60 bucks, and took me less than an hour to pull it off a green '79 Scottsdale (I was taking my time enjoying a sunny winter day) Note: not even gonna touch it till summer, I am not painting in the winter ever again |
Re: Restoring Rusty
Great buy even with all the extra cost they added.
|
Re: Restoring Rusty
Quote:
Thank you! |
Re: Restoring Rusty
Nice. I could use a pair in that color, haven't seen one in a yard though.
|
Re: Restoring Rusty
Quote:
Thank goodness we can still buy Gunk Engine Degreaser. I'll have to try mineral spirits, too. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - Header Reinstall
3 Attachment(s)
OK got her buttoned up whilst listening to the Colts handle the Bengals on the radio
not perfect, but much cleaner, even wire brushed the manifold bolts, wish I knew how to keep them from rusting again cause painting bolts hasn't worked for me, the paint just twists right off as I install them, also wish some of these pictures came out better |
Re: Restoring Rusty - Passenger Manifold Comparison
2 Attachment(s)
and this is just to compare how the passenger side exhaust manifold area looked like when I got the truck and how it looks today, a bit of improvement wouldn't you say
|
Re: Restoring Rusty
You need to clear those bolts or paint them or something, they rust 10x quicker after being cleaned up w/a wire wheel.
|
Re: Restoring Rusty
Looks better. Did you install new valve cover gaskets?
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
New bolts are zinc coated in most cases. While they may be a little ugly after the decades, when you strip all the zinc off they get rusty fast like any unpainted steel.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Good reading. Nice chronicle.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - TRANSMISSION CONTROL SPARK SYSTEM
I decided I would clean up and decluter the engine bay a bit before bolting on my new intake, carb, and air cleaner, that way I won't get any of that old electrical tape glue and grime on the new shiny bits
so if I may borrow a term from the Import Crowd, I will be "deleting" the Transmission Controlled Spark System, TCS say what? The Transmission Controlled Spark System is used on all 10 Series vehicles, C-K20 suburban, G20 Series and G30 Sportvans when equipped with a manual transmission. lucky me so what does the TCS do? Control of exhaust emitted by vehicles using the eight cylinder engines, is accomplished by eliminating ignition vaccum advance when the vehicle is operating in reverse, neutral or low forward gears sounds great - lets get rid of it |
Re: Restoring Rusty - TCS Time Relay
1 Attachment(s)
first we introduce the five usual suspects
TCS Time Relay, this bad boy hides behind the brake booster on the fire wall, I am just going to unscrew it, (one bolt) and leave it plugged in to the wiring harness which will be yanked out anyways |
Re: Restoring Rusty - TCS Temperature Switch
1 Attachment(s)
next is the TCS Temperature Switch, this redundant temperature switch lives in the right cylinder head between the #6 and #8 exhaust ports (unlike it's much more useful cousin in the left cylinder head between #1 and #2 exhaust ports)
for now I will just unplug the single green wire from it and leave the temp switch in the head, sometime later on when I feel like draining the coolant (again) I will replace it with a nicer plug |
Re: Restoring Rusty - TCS Vacuum Advance Solenoid
2 Attachment(s)
the TCS Vacuum Advance Solenoid sits in the front right of the intake manifold, next to the oil filler cap in the photos, both pictures show the same solenoid just from different angles as it is buried behind the heater core hoses
|
All times are GMT -4. The time now is 08:29 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com