Youtube channel with how to videos on metal work
 

Those following my build thread have seen me install a new floor pan and I have finished the passenger side cab corner, pillars, inner & outer rocker.

I decided I would try to record the Drivers Side from start to finish so there was a complete step by step video series on this. I know there are a lot of bits and pieces on youtube and a lot of good threads but the videos skip a lot of steps. I know it would have made my life easier so here you go.

https://www.youtube.com/channel/UCkS..._as=subscriber

Re: Youtube channel with how to videos on metal work
 

Thank you, just subscribed and will check them out. Have to replace the inner and outer rocker panels on my 69 and will be the first time ever doing anything like this.

Re: Youtube channel with how to videos on metal work
 

Subscribed! I too have to do this work on my 68 and my 70.

It is true that there are a lot of videos out there, but it's nice to have one from a board member, it somehow lends credibility to it for me.

Re: Youtube channel with how to videos on metal work
 

Thanks! This is a job in my future. I’ll check it out.

Re: Youtube channel with how to videos on metal work
 

Just downloaded to watch them tomorrow on my down time.

Re: Youtube channel with how to videos on metal work
 

Thanks, I posted another video last night finishing up the pillar. Showed some shrinker techniques. :)

Re: Youtube channel with how to videos on metal work
 

Subbed to watch this weekend:metal:










.

Re: Youtube channel with how to videos on metal work
 

Tomorrow im hoping to seal the inside of the pillar and cab corner so by the weekend you should see a lot of progress. Warmest day weatherman is calling for a while here....

Re: Youtube channel with how to videos on metal work
 

I managed to get the cab corner/pillar finished up for the most part and uploaded two more videos. There are 4 parts and 1.5 hrs of video total which I think give a pretty good walk through of everything.

Now on to the outer rocker!

Re: Youtube channel with how to videos on metal work
 

I uploaded part 1 of the outer rocker video. This one doesnt look like it will take nearly as much work to get done as the PS did.

https://www.youtube.com/watch?v=dY6qtxZ9-9g&t=834s

Hopefully these help people years to come....

Re: Youtube channel with how to videos on metal work
 

Second part of the rocker video is uploaded

https://www.youtube.com/watch?v=KEmunwBMAlg




.

Re: Youtube channel with how to videos on metal work
 

Thanks. I’ve been watching.

Thanks for the support!!
Posted via Mobile Device

Re: Youtube channel with how to videos on metal work
 

Watched every one also

Re: Youtube channel with how to videos on metal work
 

Been watching, good stuff. Like the ironing board toolbench too, very relatable!

Re: Youtube channel with how to videos on metal work
 

Thanks for the support! I hope to see this grow.

I'm going to try and get a how to video on all the common places so ill have to do a second cab to get one of the floor pan and front pillar. I've already had two people contact me to do theirs but they were kind of far away and if I did one for someone Id want them to be close. That way they can come often to see progress etc....

Re: Youtube channel with how to videos on metal work
 

Nice. Seems like an honest demonstration of the issues with the replacement parts, which is often not shown.

Re: Youtube channel with how to videos on metal work
 

That is one of the exact reasons why I started this.

Re: Youtube channel with how to videos on metal work
 

you got my attention , what would be your number for floor pan , cab corners and rockers and a few other odds and ends?

Re: Youtube channel with how to videos on metal work
 

Part 3 of 3 is now up for the rocker panel install, turned out nice!!!

https://www.youtube.com/watch?v=F9viASzV8Yg




.

Re: Youtube channel with how to videos on metal work
 

I just uploaded part 1 (of 2) on the inner rocker.

In part 1 I show how I make my own inner rocker from scratch and also how it ties into the rest of the cab. Part 2 I will show how to install the inner rocker.

https://www.youtube.com/watch?v=4d6oxnMvrDc



.

Re: Youtube channel with how to videos on metal work
 

Great Channel:metal:

Your doing a great job!!








.

Re: Youtube channel with how to videos on metal work
 

Thank you for these YouTube videos. They are invaluable learning opportunities and references that have helped me tremendously as I work on a 72 cab. Your explanations, techniques and detailed documenting helps me understand and rethink my approach. Motivating and inspiring. I'm learning as I go and this is one of the greatest resources out there. I'm not doing a total floor replacement but everything you cover is extremely helpful. Thanks again and keep up the great work!

Re: Youtube channel with how to videos on metal work
 

Subscribed and have really enjoyed your videos. Did you make a video on the full floor replacement?

Re: Youtube channel with how to videos on metal work
 

Thanks Getter-Done!


Thank you for the words. Appreciate the support.

Thanks! Not yet. I might have another cab coming and I will make a video series on that if I get it.