Re: Restoring Rusty
3 Attachment(s)
when I bought the step side bed, Al also let me have this front clip for only $100 bucks, I know I owe him big time
I hope to swap my taco hood for the one off of this one, as well as use this new(er) or other(er) driver side fender I may also use the hinge springs off of this one since mine are shot |
Re: Restoring Rusty
5 Attachment(s)
got to play in the garage a little bit today, and had that front clip in pieces in no time, taking things apart is so therapeutic (you should try it some time, hee hee)
|
Re: Restoring Rusty
3 Attachment(s)
unfortunately the passenger side inner fender was toast, they often are, they like to rot right under the battery tray, however surprisingly the core support is solid down there, surface rust mostly but strong and thick still, I might sell it if anyone needs one, the originals are extremely hard to find in good nick, how about one million dollars, never been raced, ran when parked?
|
Re: Restoring Rusty
Well get this my brethren, we once again was served a 60 Day Notice to move out, yup our landlords want to sell the house (and we asked them when we moved in only 18 months ago if they had any intention of doing so, oh well they have the right to change their minds) but the timing couldn't be worse, we want to buy a house this year but not rush and find something in 60 days
So at least this time Rusty is all in one piece and runs great, so he will come in handy, but I am hiring pro movers since I did hurt my back and I'm no spring chicken. In related news I am downsizing from a 3 car garage back to a 2, I know I know, Cry for me Argentina! Good News is we already found a house a little bit closer to the kids school, and in the same area just half a mile away. |
Re: Restoring Rusty
You lost one house and found another in four paragraphs? Man, you are quick. :lol:
|
Re: Restoring Rusty
Man, sorry to hear about the house. Total swift kick in the (name anyplace that hurts). Glad you found something so quick. Good (great) grab on that front clip. You blew it apart fast. You are on your way to having a spare Not So Rusty. I hope the pack-up-and-re-lo-cate goes well.
|
Re: Restoring Rusty
Sucks you have to move again. I hope the new digs will suit you and your family a long time or until you if d more permanent digs. That front clip is really making me jealous. Gosh do you really need that. I will give you 150 for the whole shebang. Lol.
|
Re: Restoring Rusty
Gregski, sorry to hear about the house situation, but then happy that you already have a prospect in mind.
Looking forward to seeing what happens with Rusty (Fleet or Stepper). |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
So moved in to the new house over Superbowl Weekend
Couldn't resist taking this pic of one of the first boxes moved. Epic! |
Re: Restoring Rusty
1 Attachment(s)
Truck Doing Truck Things!
Rusty sure earned his keep! I don't know how people live without a truck in their stable? |
Re: Restoring Rusty
1 Attachment(s)
One load down, dozens to go...
Apologies for posting one pic at a time, its all my iphone allows me to upload at once |
Re: Restoring Rusty
1 Attachment(s)
Since I went from a three car garage to a two I tried storing some truck parts in the kitchen, but the wife didn't go for it😳
I don't get chics, hee hee |
Re: Restoring Rusty
1 Attachment(s)
When it was all said and done you couldn't fit a que tip in that garage...
Fun Level = 1.1 |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
:haha:
Quote:
|
Re: Restoring Rusty
Glad you got moved. Can't believe you sat that box like that. Can't you read? Lol.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
Captain's Log March 3rd, 2017, today Rusty becomes my Daily Driver. That's right after a 3 year lease I returned my electric Nissan Leaf and will try to drive this 1974 rig on a daily basis, wish me luck.
|
Re: Restoring Rusty
3 Attachment(s)
so finally got a couple hours to work on the truck, one thing that needed doin' was to swap the side hung float bowls with the center hung ones on this Holley carb, this also called for replacing that silly little straw connecting the two float bowls with the single fuel inlet with a proper dual inlet hard line (though I am not a fan of the hard line and may try a rubber hose solution some time down the line)
|
Re: Restoring Rusty
4 Attachment(s)
the last time I attempted this swap I did not have these two coupling adapter thingies to screw in the smaller fittings of the hard line into the much larger openings in the float bowls
so I scored this one on eBay... |
Re: Restoring Rusty
3 Attachment(s)
and this second coupling I bought directly from Holley, same thing just a little bit more money
I honestly don't know where the smaller gasket is supposed to go as it just falls in if inserted towards the cab side |
Re: Restoring Rusty
3 Attachment(s)
so having those two thingmajigs allowed us to mount the chrome hard line to the carb, it took some gentle persuasion to separate the inlets to be as wide as the carb they came about 1/4 inch too narrow I think, hey aftermarket parts right!!!
|
Re: Restoring Rusty
4 Attachment(s)
then the typical interference problems started, hey it's Hot Roddin' aint it, nothing fits on the first try
that pesky chrome hard line hit the water inlet/outlet for the heater core in the intake manifold, go figure right?! well we was ready for that, so I busted out one of my trusty 1 inch 4 hole plastic carb spacers and gave that a go |
Re: Restoring Rusty
3 Attachment(s)
well naturally now we needed longer carb studs, so we tried the 2" tall ones and not even they were tall enough
so we hit Oh'Reallys and picked up the 2 1/2" ones and they did the trick |
Re: Restoring Rusty
by then it got too dark to take a final pic, but we got everything assembled and after tightening that silly hex stud in the chrome dual hard line inlet we stopped the gushing gasoline fountain
we squirted some gasoline into the float bowls via their vent towers and the truck fired right up I adjusted the float bowls so that the gas is half way full in the sight glasses both front and rear float bowls the truck warmed up in the garage and then we took it around the block for a test drive, it ran good I kept the same carb configuration I had before: 69 primary jets / 73 secondary jets (I think best I could see) 35 accelerator pump squirter 10.5 power valve (cause I'm pulling silly strong 20 inch vacuum at idle) yellow vacuum secondary spring no idea what color accelerator pump cam, will check in the morning (what ever stock one it came with) |
Re: Restoring Rusty
Quote:
I've never owned a pickup of my own, but that's why I'm on the hunt for one. Getting into woodworking and metalworking means I need to be able to haul materials! Same thing goes with landscaping. My Wrangler can only carry so much even with the top down and the rear seat bench out! Great thread, at any rate! |
Re: Restoring Rusty
I have had a truck since I was 19. I don't like borrowing a truck. If you own a house you really need a truck. Be it big or small a truck will save you in the long run. I have a small truck. It's plenty for what I need. I get my 76 on the road and I'll have two. Glad to see you back Greg.
|
Re: Restoring Rusty
Good on fixing the hard line clearance. I had the same problem installing the one for my Summit carb. Funny...a gazillion carbs using basically the same setup on a gazillion SBCs, and it doesn't quite fit.
|
Re: Restoring Rusty
Quote:
I love wood working and am trying to learn metal working, do you have a link to some of your work or future project ideas would love to see them. |
Re: Restoring Rusty
Quote:
question for you alls do we need to put some sort of gasket, oring, washer inside the hard line fittings to mate it to the carb, I put mine metal on metal and I am wondering if it will start leaking, so far so good, but metal don't like to mate with metal really well if you know what I mean? |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
Glad to get the updates and see the progress. Looks like you are settled in to your place so congratulations on that. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
As for my woodworking, I've worked with wood ever since I was a kid, but I've only in recent years (I'm only 25) begun to really have this urge to make furniture and what not. I still have plenty to learn, but I'm happy with what I've made so far! This was my most recent, and biggest project. An entertainment center that's meant to be a built-in for my parent's house: https://c1.staticflickr.com/3/2827/3...05145c6d_h.jpg Built using cedar. Unfortunately, I had to have the lumber company "pick" the wood for me, since I didn't have a truck to go grab it all! Overall they did a great job, but I did end up with a few extremely warped boards. Looked into various methods of reshaping the boards, but I didn't have the time nor the proper means to do it! Sorry for the threadjack! |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
That corner was actually part of the design, to give the living room an actual focal point. Beforehand it was a large room with no real indication where a TV should be placed minus the built in speakers up top. Currently a 55" TV sits in it, but it will accommodate up to a 65"; they don't watch TV much, so a super large TV is not needed. Honestly, drawing everything up in AutoCad is was really made this easier. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
2 Attachment(s)
Quote:
|
All times are GMT -4. The time now is 04:05 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com