Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - Budget Top End Build
Quote:
|
Re: Restoring Rusty - Engine Stroll
2 Attachment(s)
we finally got a break in the weather and the sun came out, so I decided to take the engine for a walk
I don't get how in our fourth year of a drought here in Norther California it has been raining and I mean poring for the last seven days, (things that make you go hmmmm) |
Re: Restoring Rusty
3 Attachment(s)
doctor, the patient is prepped and ready for surgery
|
Re: Restoring Rusty
4 Attachment(s)
then it was time to [ahem] MAKE THIS ENGINE GREAT AGAIN !!!
|
Re: Restoring Rusty
Do yourself a favor and do NOT break that lower dipstick tube and do not misplace it lol. Be lucky you still have it.
|
Re: Restoring Rusty
2 Attachment(s)
somehow I am always happier behind a wheel, even if it is a 4 inch on an angle grinder, ha ha
I don't know about you, but I can find plenty of things to cut my hands on under the hood, so I decided the engine block wasn't gonna be one of them time to smooth out that casting crust |
Re: Restoring Rusty
I would replace those steel cast plugs with some brass ones while you are at it its cheap and should never leak if installed correctly that's not a fun job with the engine in the truck/car
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
3 Attachment(s)
the sharp edges around the oil filter housing got some angle grinder love too, there much better
|
Re: Restoring Rusty
2 Attachment(s)
and on to the other side
|
Re: Restoring Rusty
2 Attachment(s)
first we knock off the ugly
|
Re: Restoring Rusty
5 Attachment(s)
and by zi Pompa de Gasolina
|
Re: Restoring Rusty
2 Attachment(s)
and second side done
labor = about 1 hour per side |
Re: Restoring Rusty
Always wanted to do the type of smoothing you are doing!
|
Re: Restoring Rusty
something i plan to do when i start assembling mine...unless i forget
|
Re: Restoring Rusty
1 Attachment(s)
had to go into town fer supplies, yup this is how the magic happens
|
Re: Restoring Rusty
5 Attachment(s)
it was a nice day so I decided to have a little pool party and all the dirty bits were invited
|
Re: Restoring Rusty
5 Attachment(s)
word quickly got out and friends invited their friends, dirty little rascals
|
Re: Restoring Rusty
5 Attachment(s)
and a few more
the harmonic balancer was a dirt magnet for sure, I'm surprised it stayed balanced with that 9 pounds of dirt stuck to it |
Re: Restoring Rusty
2 Attachment(s)
while those bits were soaking I got started on the engine
got the front side cleaned |
Re: Restoring Rusty
Check your harmonic balancer for cracks in the rubber as it may need replacing and now is a perfect time to invest in that.
Oh and your missing the lower bolt on the right side of the block at the front to secure the fuel push rod. This area WILL seep and leak oil if you do not put the bolt back in. |
Re: Restoring Rusty
Quote:
the bolt was removed during disassembly in order to slide that rod out allowing the cam to be removed |
Re: Restoring Rusty
1 Attachment(s)
Every time I try to get out - they pull me back in!
as I was spinning the engine block on that engine stand, I realized that it was sliding out of the rotating thingmajig, so I decided to use a C clamp from time to time to pull it back in, you know to prevent getting dead so if you gots a similar stand, be careful you hear, engine blocks are expensive! |
Re: Restoring Rusty
5 Attachment(s)
time to do the passenger side set of cylinder banks 2-4-6-8 who do we appreciate?
I covered the other end with a rag, and kept the cylinders slightly pointed down, so when I shot brake cleaner in there to rinse them out, the debris would flow down hill and out the cylinder, seemed to work |
All times are GMT -4. The time now is 10:00 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com