Re: Restoring Rusty
 

True dat... I removed mine last Sunday.

Re: Restoring Rusty
 

Hey man who's side are you on? LOL us rookies must stick together, don't let pros tell ya what to do! jk

Re: Restoring Rusty
 

Steering dampener?

Re: Restoring Rusty
 

Okay, I may have an unfair advantage there. I have impact sockets big enough for all these nuts, and the air impact wrench to drive them.

I did once get the pitman arm nut off with a pipe wrench with a length of pipe over the handle. I think the tighten torque is something like 160 ft-lbs, so you know it'll be tougher still to get it off.

Re: Restoring Rusty
 

I'm guessing you've seen this, but just in case you haven't Tx Firefighter did a great how-to on fixing a leaky steering box here: LINK.

Re: Restoring Rusty
 

Ya, those rag joints cut down on vibration. And they aren't the "final word" because there are two steel pins in slots so that if the rag joint ever rotted out and was too weak, you wouldn't lose your steering.

Re: Restoring Rusty
 

Just be glad you don't have to remove the actual steering arm. Those tapered cone washers are hell!

Re: Restoring Rusty
 

I worried about how to get my new gear box lined up with the pitman arm and the steering wheel/column.

Re: Restoring Rusty
 

Yeah I still hate the things. I have replaced way too many of them. So I just don't trust them. I plan to replace my intermediate shaft with u-joints as both ends. eventually.

Re: Restoring Rusty
 

I agree that the rag joint seems pretty bush-league. With proper u joints in there, how much have you noticed the vibration goes up?

Re: Restoring Rusty
 

I went to a double u joint shaft in my CJ7 (GM steering system). The pros out weigh the cons to me. The only con (for some) is you will get more "road feel". By going to u joint shaft you take out that insulator of a rag joint. but
I don't notice any vibrations just a very positive steering system where I can feel somewhat where the tires are and going through.

Re: Restoring Rusty
 

so picked up my $40 dollar power steering pump for $80 bucks from Carquest, LOL maybe the extra $40 bucks is for the pink blanket it comes with, hee hee

for $80 bucks you think they could afford to put a picture of the actual contents on the box instead of some generic pump photo

I'm pretty sure this is no better than what I got from OReilly's but we'll see, I think some of these parts come from the same source, that's why the resellers rebrand them as their own, Autozone, O'Reillys, NAPA, Carquest, PepBoys

I would prefer to see the manufacturers logo on the box, but then we could compare apples to apples price wise, and the resellers don't want that

[end of rant]

Re: Restoring Rusty
 

so started wire wheelin the frame rail and a bit under the cab in preparation for POR15, not fun, ended up removing the front bumper, again for better access

tomorrow I should paint it black with POR15 to match the other side

Re: Restoring Rusty
 

by the way por 15 doesnt stick as well to bare metal compared to to rusted. from what ive seen, just a quick one over to remove loose rust will work best.

Re: Restoring Rusty
 

I'd agree with this. I've had por-15 peel off when used on shiny steel. That's when I started using the Metal Ready spray (has some new name now) first, and that cured the problem.

Re: Restoring Rusty
 

That is because POR15 like a lot of other products are a "rust encapsulator". If you take your frame down to bare metal then use tremclad paint instead.

Re: Restoring Rusty
 

My compliments on your progress as usual and your meticulous approach is a inspiration to all of us, and i wish i had the knowledge to help you with some of your problems but all i have is a tip for you.

I have a Portable Abrasive Blaster Kit it's old and from sears but has saved me a ton of time when cleaning up parts I've seen them at harbor freight for $40 the trick is to capture the media as you use it and just reuse it.

Re: Restoring Rusty
 

I think you are right, I am learning that too, needless to say I am a bit of a slow learner, lol, that and I have a hard time accepting that I am painting over rust, but I think I am getting over it as removing it is difficult

Re: Restoring Rusty
 

The Greg is a proud owner of Metal Ready (pronounce expensive made up of a tiny bit of Phosphoric acid diluted with a lot of water and a blue urinal biscuit thrown in for color, hee hee) but hey if that's what it takes, The Greg will git er done

Re: Restoring Rusty
 

Thank you very much I appreciate that

Re: Restoring Rusty
 

welcome to another Charge of the Light [truck] Brigade

another day, another wire wheel, I swear one can easily spend as much on these wire wheels (almost $20 a pop) as the purchase of some of our "project" trucks, if I keep visiting Depot Home (as my mum says) like this I may as well suggest they open up a drive through

needless (pun) to say one must replace these every 3 months or 3,000 miles, LOL

(one of these on the LEFT is the used one, can you guess which one that is?)

Re: Restoring Rusty
 

so we managed to get some POR15 black paint on the frame rail

UPDATE: Five years later, the POR15 paint is pealing off in huge chunks the size of 3x5 cards, do not recommend this product at all!

Re: Restoring Rusty
 

so while the frame rail was drying we decided to check on our inner fender which had been marinating in a light muriatic acid / water bath

you can see where the liquid could reach, as there is a distinct line, I could not fit the entire fender into my container so I would rotate it upside down, and down side up, etc

Re: Restoring Rusty
 

I hear ya, Gregski. I've gone through a million wire brush wheels in my grinder too.

Re: Restoring Rusty