Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
I use it on Spark Plug threads and on wheel lugs. Be aware that torque specs in your service manuals are DRY not lubricated. Torques need to be derated for anti-seize lubricated nuts and bolts. Permatex has charts for this. |
Re: Restoring Rusty
Yes, use it on exhaust manifold/header bolts, collector bolts, spark plug threads, and especially any bolts threaded into your aluminum intake, thermostat housing bolts for example.
|
Re: Restoring Rusty
You WILL be sorry if you don't replace all of the freeze plugs!!! They will let loose at the most inopportune time leaving you stranded or worse over heating your engine cracking your new heads. It's not worth it for a few bucks!!!
|
Re: Restoring Rusty
5 Attachment(s)
picked up some white vinegar on the way home from work today and decided to use it to flush out the block from all the coolant rust, not sure if it was worth the $3.00 dollar investment, used boiling hot water and vinegar to do so
|
Re: Restoring Rusty
2 Attachment(s)
used painters tape to block off the cylinders to prevent vinegar and or water from splashing down upon them, then I was super careful
|
Re: Restoring Rusty
3 Attachment(s)
Quote:
|
Re: Restoring Rusty
3 Attachment(s)
all in all, it was pretty much an all to do about nothing type a day, I worked my butt off but had not much to show for it
I cleaned bolts and washers and more bolts 1. oil pan bolts 2. timing cover bolts 3. water pump bolts 4. intake manifold bolts 5. valve cover bolts 6. crank gear bolts 7. fan bolts 8. fly wheel bolts 9. pressure plate bolts 10. bell housing bolts I cleaned the oil pan, it may need a little touch up paint I cleaned the timing cover, its ready for paint and a new seal I Mickey Moused with the thermostat gasket on the new Vortec intake manifold with a razor blade, until no one was looking, then I called in the heavy artillery trying to decide weather I clear this thing or paint it Cast Iron to match the heads and the block, its pourous and a pain to clean, I can only imagine it being a dirt and grime magnet in the truck hey I cleaned my workbench.... again |
Re: Restoring Rusty
So the plan is to put the engine back together on Saturday (that's 4 days from now), the original plan for March Madness was to have the engine back in the truck by then ie all in one month, but then I had my set back(s) with the Vortec heads, so I'm sure you'll forgive me for falling behind
so here's what's left to do in the crunch time 0. chase / tap all the bolt holes in the blockI don't want to rush, but at the same time I don't want this engine sitting in two dozen pieces for eternity, I'm sure you know what I mean. Though I work hard and do the best that I can, at 43 I learned that I rather have something completed at 80% quality, than strive for 100% perfection and never complete it! |
Re: Restoring Rusty
1 Attachment(s)
saw this Lucas Engine Break-In oil Zinc additive at AutoZone today while buying new belts, seems like they don't carry engine break in oil any more, neither does Oh'Reallys
The GM Start-up and Break-in Procedures, Specifications 19210008 only say use 10w30 motor oil (non-synthetic) and nothing about Zinc |
Re: Restoring Rusty
Quote:
Keep in mind though if this were a full rebuild you would want some straight 30 weight to help seat rings on first start up and to reduce initial bearing wear. "Steps off soap box" |
Re: Restoring Rusty
Not sure if its available in the US but up here in the great north we have a company who makes specialized oil for old vehicles and bikes. It is a 10w40 oil which is good for most cars and motorcycles but it contains large amounts of ZDDP to help the wiping of critical engine components.
http://www.camoils.com/ |
Re: Restoring Rusty
** Duplicate **
|
Re: Restoring Rusty
1 Attachment(s)
Quote:
Quote:
Quote:
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
Quote:
|
Re: Restoring Rusty
Joe gibbs have a good brake in oil,is it not sold in Cal.?
|
Re: Restoring Rusty
All flat tappet cam engines need ZDDP oils, I use Royal Purple HPS 10W 30 in mine.
|
Re: Restoring Rusty
Brad Penn break in oil is what I'm using. Supposed to have the required ZDDP from what I've read and I've read A LOT on it.....
|
Re: Restoring Rusty
I will 3rd the Rotella. That is what I used for the engine in the Jeep last year.
|
Re: Restoring Rusty
I've been running synth since after break-in. Mobil1 10W30 with half a bottle of this added each oil change.
Amazon.com: ZDDPPlus ZDDP Engine Oil Additive... |
Re: Restoring Rusty
Quote:
So I made a call to the GM machine and hopefully the right people will be contacted on the issue :chevy: "steps down drops mic" :lol: |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
now I also heard you don't want to use a multi weight oil for the break in but should run a 30 weight instead, The Greg's head is about to explode
|
Re: Restoring Rusty
Well your only breaking in the came so its not as "crucial" I have heard of guys with good success doing none straight weight 30 in a tight spot with fair results but I have never messed with it as I have always had it available and never have seen a need to risk it I found an alternative for you by the way greg if this one does "blow up" due to my attempted help
GM part number 19201333 I will cut you a deal buddy :lol: |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
For example: http://zddplus.com/ |
Re: Restoring Rusty
Doesn't Comp Cams still sell their break-in oil? I can't imagine they wouldn't. Break it in with that and be done with it, run something like Valvoline VR1 or anything w/some zddp in it after that. One episode of pretrol primates they blew up a new motor trying to break it in with cheap motor oil and a bottle of zddp additive. They used a good break in oil after getting it rebuilt again. Use something decent made for break-in and fuggetaboutit.
|
Re: Restoring Rusty
Greg, Get some of this:
http://www.summitracing.com/parts/crn-99002-1/overview/ Coat all the lobes with it, rub it in good, Also the bottoms of the lifters before installation. Has served me well for years. Valvoline VR-1 conventional oil in the silver bottle or Brad Penn breakin oil is what I use for flat tappets. |
Re: Restoring Rusty
Quote:
The bearings in a diesel engine are made from the same steel copper and babbit as the gasoline engines. Detergent in the oil keeps crud in suspension and can knock loose filth in a sludged up motor. Diesel oils have more detergents to keep the carbon suspended so it doesn't sludge up your motor to begin with. The origination of this rumor is probably that you can get into real trouble on old poorly maintained motors that were run on non detergent or poor detergent oils by changing to high detergent diesel oils... Detergents and dispersants tend to knock a lot of the sludge loose in a hurry and plug stuff up. Diesel oils tend to have more generous quantities of anti-wear additives like Boron, Zinc & Phosphorous (Zinc Dialkyl Dithio Phospahte), and Molybdenum than Spark ignition only oils. With the tightened emissions requirements put in place around 2007 they don't have the phosphorous or zinc levels they used to. If you're installing a new cam I'd run a break in oil like Joe Gibbs till it's fully broken in and then run the Rotella T5. I run 5W40 Rotella T6 in my LS4 Impala, 2 6.5L diesels, and my Polaris Sportsman 500HO ATV. The 6.2L CUCV and the LDT 465 Continental in the M35A2 get 15W40 Rotella T5. Look at the API seal on the back of the jug. Rotella T5 is at least SM and CJ-4 rated. S is Spark ignition C is Compression (diesel) ignition. |
Re: Restoring Rusty
3 Attachment(s)
well gentlemen when the Greg gets in the zone he gets in the zone, I'm sure you've been there where you just put you head down and git 'er done, well today was such a day, a good day, so lets get to the updates
came home from work and turned up the paint booth to 61*F plus and dropped the humidity to the low 40% and busted out my paint guns check it out this dude's shooting primer on his tin first, he's Legit! painted the timing cover |
Re: Restoring Rusty
3 Attachment(s)
painted the valve covers
|
Re: Restoring Rusty
2 Attachment(s)
even the oil pan joined the party, for a light dusting of a touch up
|
Re: Restoring Rusty
5 Attachment(s)
a while back the Alan Grove knock off mid mount alternator bracket showed up so it got a coat of sexy Semi Flat black paint too
the bracket is painted black in the last pic, whether the sun wants us to see it that way or not, lol |
Re: Restoring Rusty
4 Attachment(s)
than the fraternal twins showed up and they wanted to get in on the action, apparently they were not too happy with their white "silver" coating, and I don't blame them - so they opted for the Cast Iron sheen but of a higher temperment than the engine Enamel
these are the as before shots |
Re: Restoring Rusty
4 Attachment(s)
and after the upteenth coat they turned out great, I absolutely love this color now
used the same VHT brand as before except a darker color - do you like? |
Re: Restoring Rusty
3 Attachment(s)
and don't forget this little feller
|
Re: Restoring Rusty
http://www.drivenracingoil.com/#prettyPhoto/0/
This man knows what he is talking about. It might sound like just an ad to sell oil but I have met him and read a lot from other people, he knows what he is talking about. Diesel motor oils have had a lot of the ZDDP's removed from their oils. It used to be a common thing to used Delo or Rotella but not anymore. Also the ZDDP's work at a different operating temp. A diesel motor has higher internal engine temps compared to a gas motor. Straight 30 weight is a thing of old. Either use a break-in oil or use a 10-30 with the additive. If you are going to use synthetic then wait about 5,000 miles before making the change. I have a camshaft at work from a brand new motor. 5 lobes went flat instantly because the mechanic decided he did not need to put in the additive that we gave him. There are so many opinions on this and its an on going debate. Again watch the video its explains a lot. |
Re: Restoring Rusty
I have a lumpy flat-tappet cam with some fairly stiff valve springs.
I used Comp Cams break-in oil for the first 20 minutes to break in the cam. Then drained the oil (don't look at it, trust me). I then used Comp Cams break-in-oil to go break in the rings for about 100kms. Then drained the oil. I currently use Lucas Hot Rod oil with every oil change. http://www.buylucasoil.com/img/Lucas....%20bottle.jpg |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Oh, I also bought a 7/8" ball hone to make sure the lifter bores would allow the new lifters to rotate. No lobes lost yet (over two years of daily driving).
|
All times are GMT -4. The time now is 02:14 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com