Re: Restoring Rusty - Anatomy of a Kick Panel
Quote:
|
Re: Restoring Rusty - Anatomy of a Kick Panel
3 Attachment(s)
Quote:
|
Re: Restoring Rusty - Anatomy of a Kick Panel
Quote:
|
Re: Restoring Rusty - Anatomy of a Kick Panel
Quote:
|
Re: Restoring Rusty - Anatomy of a Kick Panel
Quote:
|
Re: Restoring Rusty
Good Morning, Where oh where did the gas go???? Could the gas you lost of been spilled when someone possibly siphoned it out while you were gone?
God Bless, Terry |
Re: Restoring Rusty
On that e-brake handle.. I just bought a new handle from Ebay. I broke off the remaining old plastic and clean the shaft. Then I took a propane lighter and heated up the new one and slide it on. Once it cools, its on there like concrete!
Enjoying the posts!! |
Re: Restoring Rusty
Would this be the part for the z bar?
summitracing.com/parts/gmk-4041951587s/applications/make/chevrolet/model/k10-pickup |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
More Turck Trouble
So the truck started fine in the driveway and I drove it into the garage to tighten the oil pan and valve covers a bit. Then I started it again in the garage and oh my god it sounded amazing, perfect! So I said let me drive it to a gas station half mile away to fill it up. It drove fine at first then it started to fade, it seemed like it wanted to stall / die at each stop sign, I had to rev it up a bit when coming to a stop, then I barely made it to the gas station and it died at the pump without me having to turn the key off So I filled the tank up with gas, went to start him up, and it cranks but does not start. The clear fuel filter is almost dry there may be a 1/16 of an inch at the bottom of the glass (the fuel filter sits horizontally right before the carb) What is going on? Background information: I dropped the tank a few weeks/months back. It was very clean on the inside no rust at all. I also replaced the rubber hoses from the gas tank to the hard fuel lines both the 3/8th to line, and the 5/16th return line. Also the previous owner told me he put on a brand new fuel pump and it did look new to me when taking a look at it. |
Re: Restoring Rusty
Sounds like it might be sucking air. I would verify all the clamps are tight and make sure there are no cracks in any of the lines.
|
Re: Restoring Rusty
does it have dual tanks? Mine did the same thing when I first got it. I drove it around for a few days no problems. Then the switch over valve got stuck between RH and LH sucking from both tanks when one tank went dry she stopped running even though the other tank had a full tank. I never seen that happen before either.
|
Re: Restoring Rusty
wife gave me a ride home and we left Rusty parked at the gas station, young man at the register helped me even push him into a parking spot and away from the pumps, kid appreciates old iron, God bless him
came home had pizza fer dinner and drove back out to check on Rusty about an hour later with my tools Rusty fired right up on the first try and I drove him home ... to be continued |
Re: Restoring Rusty
Quote:
lines are good I installed a plastic see through fuel filter in the middle of a new black fuel rubber line between the hard line and the fuel pump I also unscrewed the hard line from the fuel pump that goes to the carb and cleaned the threads with a wire brush and brake cleaner, there was some left over teflon tape on the threads that was all shreded and what not so I cleaned it up read good and dabbed a tiny bit of orange RTV gasket maker on the threads and screwed it back in nice and proper with a proper pipe wrench ... to be continued ... |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
5 Attachment(s)
let's take a quick break from the troubleshootin' and talk about some fun stuff
came home and found this: FYI: The quality is horrible, the top lid came already bent in one place, but I just used my thumbs to bend it back, since the top is made out of a single recycled 12 oz beer can, I kid you not |
Re: Restoring Rusty - Mr. Gasket Air Cleaner
4 Attachment(s)
Well let's see it on the truck.
So what do you all think? Better or worse than that Darth Vader helmet? which by the way is for sale for only $50 plus shipping, best part is NEVER BEEN RACED, lol, pm me and yes now I need a shorter stick to clamp this thing down with a wing nut, god forbid my three air cleaners were all the same height, jk |
Re: Restoring Rusty
Now, I like that air cleaner assembly. ;)
|
Re: Restoring Rusty - Painted the Kick Panels
5 Attachment(s)
it was a nice day so I painted [ahem] stained them kick panels
three light coats, you know the drill |
Re: Restoring Rusty
5 Attachment(s)
whilst the paint was drying it was time to drill out the rivets and separate those air vent valves so that we can clean, prep and paint the metal and sandwich new rubber fillings in them eventually
|
Re: Restoring Rusty
2 Attachment(s)
I buy you new shinny things, I clean and paint your bits, and this is how you thank me Rusty?
There is literally oil drizzlin' out of the top bolt hole behind the fuel pump? Is that supposed to be a blind hole? Do I have a crack in my block gentlemen? What gives? Please advise? |
Re: Restoring Rusty
That is the fuel pump retaining bolt hole. Put a bit of teflon tape on a short bolt and tighten to stop the leak.
|
Re: Restoring Rusty
The hole is open to the fuel pump push rod. Install a 3/8 bolt about a half inch long with a lock washer and thread sealer and that should fix you up. When changing a fuel pump you can snug a longer bolt in that hole to hold the fuel pump push rod in place so it wont slide out against the adapter plate and cause you grief and anguish.
|
Re: Restoring Rusty
3 Attachment(s)
Quote:
|
Re: Restoring Rusty
Smart people...
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Vent not clogged up or maybe hung up somehow and preventing it from allowing the gas to be sucked out of the gas tank? If the pump is working then there's a air leak some where I would suspect..... Hope you get it fixed soon.
|
Re: Restoring Rusty
Quote:
So, you got two lines to the tank, or three? If no vent line, all you have to do is drill a 1/16" hole in the gas cap. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
If I remember right his truck is a '74 which would make it emissions exempt in California.
|
Re: Restoring Rusty
Yeah, I think it depends on how it was equipped when new. No vent line means vented cap.
Of course you can check it by driving it till it stops, then open the gas cap. Sucking sound, then runs fine means no vent line. |
Re: Restoring Rusty
I feel for sure we are looking at a venting issue. It makes some what sense in what he is saying is happening with his truck. Hopefully we will find out.
|
Re: Restoring Rusty
1 Attachment(s)
thank you all for helping me with the fuel issue
my tank has a vent that goes to the filler neck and then two hoses run to the engine bay one for fuel the other for evap to the charcoal canister let me give you some updates today I plugged that bolt hole that was leaking oil, I am sure I caused this issue when I deleted the A.I.R. pump as it looks like the bracket was attached to those holes, so I took one of the original bolts, cleaned it, put a little RTV on the threads and screwed it in here's a pic of the Air Pump bracket |
Re: Restoring Rusty
4 Attachment(s)
I decided to get started on the brakes since I didn't want to trouble shoot a truck that won't run when it also may not wanna stop
so this is the situation the darn brake master cylinder looks like this after a short drive, all wet |
Re: Restoring Rusty - Brake Master Cylinder
5 Attachment(s)
so time to remove the brake master cylinder
I just had to take a peak inside, since part of me considered rebuilding it myself, like my daddy and I used to do back in the 80s when parts were fixable not replaceable I was able to remove the first valve but I do not have needle nose pliers or the special pliers to get the other snap ring out which is half way down the cylinder |
Re: Restoring Rusty
2 Attachment(s)
there is nothing wrong with the power booster other than being ugly, so it had to come out for some beautification
the brake power booster is attached to the firewall with 6 studs, 4 are easy to get to, 2 are not the top 2 or easy the middle 2 suck the bottom 2 are easy |
Re: Restoring Rusty
5 Attachment(s)
brake power booster removed
that perished black rubber gasket / grommet is a concern of mine |
Re: Restoring Rusty
3 Attachment(s)
lets clean this thing so we can paint it flat black
... there that's a bit better |
Re: Restoring Rusty
1 Attachment(s)
ok, with the brake power booster off, tomorrow we will clean up this wiring mess and the fire wall may even get some touch up paint, even that baby powder will be gone, hee hee
|
Re: Restoring Rusty
3 Attachment(s)
take a look at the brakes is one of the things I always do when I buy a new used vehicle, so 8 months ago I checked Rusty's well 3 out of 4 as I couldn't get the driver side rear drum off
now I told myself I'll get around to it real quick and since the other side looked decent I wasn't in a rush well 8 months flew by and it was time to get that drum off, first I warmed up by getting the passenger side drum off, it came off easy with my hands |
All times are GMT -4. The time now is 06:11 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com