Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
Quote:
Here is the key, work on it for an hour or two then walk away. I did this over a three day period, I am not bragging the results are OK, but it is tedious work. So Saturday I think I started and did 4 hours, then on Sunday 2 hours before the football games then maybe another 2 at night, and then today after work maybe a good 4 hours on it. |
Re: Restoring Rusty
Alrighty then...
|
Re: Restoring Rusty - Neutral/ Reverse Wiring Harness
2 Attachment(s)
so I remembered why I cleaned the transmission in the first place, I needed to unplug the TCS system wiring harness and reroute the neutral / backup lights wiring harness
the light green / dark green neutral/reverse wiring harness runs under the transmission tunnel up the fire wall in the engine bay and enters the cab under the brake booster... why? I ran mine out the transmission cover and directly into the cab then made a left to where it plugs in under the dash, to do so I had to take off the plug to be able to feed it through the small hole in the firewall here I show you how to carefully remove the flat blade wire connector from the plug without damaging it or having to cut the wire and re crimp, just press on one side of the blade and it comes right out, good to know |
Re: Restoring Rusty
tranny came out real nice
|
Re: Restoring Rusty - Its Fender Time
Quote:
|
Re: Restoring Rusty - Its Fender Time
Quote:
|
Re: Restoring Rusty
Yep, Pick N Pull does core charges. Maybe they want to sell the scrap metal after, who knows.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
You got to admit they are pretty sharp ,they sell used anti freeze for cheap instead of paying a company to take it ,they sell the used oil to recycling companys .Im glad they are there as it does keep prices pretty affordable .I just wish they would open one near me ,Heck I would lease them the land for certain discounts as I have 40 mostly unused acres in pasture .
|
Re: Restoring Rusty
It is a perfect crime... er... business model...
|
Re: Restoring Rusty
The tranny looks good.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - HEI Distributor
4 Attachment(s)
replaced the stock points distributor with an HEI model made by ProForm
for now I just connected it using the stock pink resistance wire until I pull a 12 gauge OEM one from a junk yard to replace it with (seems to be running just fine even if it is only pulling 9 volts instead of 12) the pink wire was spliced into a yellow wire running down to the starter which I just cut off (and will delete at a later time) set the initial timing (no vacuum advance to 6* at 900 RPM) then I connected the vacuum and it started idling at 1,400 RPM so I backed the idle speed down to about 800 (not sure what I am doing exactly) |
Re: Restoring Rusty - HEI Distributor
I bet you will like it better if you bump the timing up more like around 10-12*.
|
Re: Restoring Rusty - HEI Distributor
Quote:
|
Re: Restoring Rusty - Tune Up
3 Attachment(s)
In addition to an oil change I always perform an old fashion Tune Up to any used car I buy.
In this case I held off on the tune up (aside from visual spark plug inspection and re gap to .035) because I knew I was going to be replacing the distributor with an HEI design, which dictates new (different) spark plug wires anyway did you know HEI is not a company that makes these distributors but actually just a GM acronym for High Energy Ignition. I did not know that till recently I thought some company called H.E.I. which maybe stood for Something Something Inc made them, LOL I used the ACDelco R44T Mexican spark plugs like the manual calls for, and Duralast (made in USA) new plug wires deisgned for the HEI distibutor (difference being the dizzy end is a female, on the traditional points dizzy the plug wire end is a male) I also regapped the new plugs from .035 to .045 cause you can run them hotter with an HEI distributor |
Re: Restoring Rusty
Quote:
I have no idea why GM just didn't stick with an under-hood ballast resistor. Guess they must have had a reason. On the GTO, the resistance wire's heat had begun to melt insulation on other wires in the underdash bundle. On another note, what are your impressions of the Proform distributor? |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
Very good question and I am holding off on any disclosure as it is clearly too early to judge. I was skierd by some posters saying don't buy these cheap distributors made over sees, buy a used GM one from the junk yard then replace every single part on it with name brand parts, that didn't make much sense to me. I picked Proform for two reasons: 1. I am stupid and don't like the "look at me" red MSD distributor everyone and their mother is running, I also think they are grossly over priced 2. I happen to call Proform and speak with their Technical Support staff, and A. They have a Technical Support team (unlike LMC Truck catalog folks) B. They were very kind, professional, and helpful, I hung up the phone and ordered the part. So more on the performance of the dizzy later. |
Re: Restoring Rusty
I was thinking that cylindrical thing you were looking for was actually under the cap along with the points. I don't know for sure but this is just what I thought. When my uncle got first got my '76 it had points. Somebody had swapped out the HEI for a points distributor. Soon as he replaced it with the HEI he was very happy. Oh so many years ago that was.
|
Re: Restoring Rusty
Nothing at all wrong with the Proform unit. Sure, stock HEI units work fine for stockish engines, but the problem for me has been finding them with advance mechanisms still in good shape in the salvage yard, plus you still buy new cap, rotor, mechanical advance kit, adjustable vacuum advance... by that time you may has well gotten the aftermarket cheap new one and avoid the headaches. I bought the Accell one though for $119.
|
Re: Restoring Rusty - New Distributor
3 Attachment(s)
so this is what the new HEI distributor looks like installed, it sits rather low
pardon the wiring harness mess, it was all tidied up and then I tore into it again |
Re: Restoring Rusty - Fun With Tanks
5 Attachment(s)
decided to drop the tank to see if I can fix the following two problems
1. fuel gauge not working 2. tank difficult to fill up at the gas station, acts as if it is already full and stops every 5 seconds or so so first I removed the three phillips screws from the filler neck, and learned you can drop the tank with the filler tube attached there is enough wiggle room |
All times are GMT -4. The time now is 10:43 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com