The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=4)
-   -   Restoring Rusty (https://67-72chevytrucks.com/vboard/showthread.php?t=645440)

Gregski 12-15-2018 04:45 PM

Re: Restoring Rusty
 
2 Attachment(s)
so looking back at my own thread last May I put on the whole brand new Edelbrock Top End (aluminum cylinder heads and aluminum intake) I think the mistake I made was re using my old tin 43 year old valve covers, how can I be so dumb, well I was broke and I thought how crucial are stupid valve covers anyway, well one greasy driveway and oil all over my engine bay I say they are pretty important, so I ordered some brand new tall style ones from Summit (back in June, but didn't install them, neck punch!)

Gregski 12-15-2018 04:47 PM

Re: Restoring Rusty
 
3 Attachment(s)
honestly I think the problem may have been the stupid hard rubber gaskets that I got instead of the cork ones, but either way let's install some brand new valve covers, how hard could it be?

oh yeah, also got some of these wide/long [cancer causing, but only in California] valve cover hold downs

MikeB 12-15-2018 06:47 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8406014)
Oh yeah, also got some of these wide/long [cancer causing, but only in California] valve cover hold downs

Just about any car part I get now has that warning attached. I wonder if every car and truck sold in CA gets one? Toaster, refrigerator, frying pan?

Talk about a "nanny" state. Politicians there are totally out of control. :crazy:

Gregski 12-15-2018 07:20 PM

Re: Restoring Rusty
 
2 Attachment(s)
with the thicker gasket I needed longer bolts

and here's how the short pressure plates compare to the more longer ones (I dig the black ones, most local parts stores carry the chrome ones and in a pack of four, ie two packs needed)

Gregski 12-15-2018 07:26 PM

Re: Restoring Rusty
 
3 Attachment(s)
well even after all the wandanglin' and shandanglin' after careful examination and re examination the Summit brand tall valve covers (be as nice as they were) would not properly mate with these aluminum Edelbrock E Street heads, it kept on feeling like I was hitting metal on metal and my only option was to glue two cork gaskets together but I had another idea...

I used the rusty chrome MOROSO valve covers I got off of Pontiac Mike for a twelve pack (of Taco Bell tacos)

he cleaned one up for me with sum steel wool, I guess he thunk I would treat the other one with the same respect, ... Not!

I like to goop the valve cover side of the gasket with red bare back buffalo snot to hold the gasket semi in place as we mount it

hatzie 12-15-2018 07:29 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8406109)
with the thicker gasket I needed longer bolts

and here's how the short pressure plates compare to the more longer ones (I dig the black ones, most local parts stores carry the chrome ones and in a pack of four, ie two packs needed)

I think I'd consider the center bolt valve covers. They seemed to seal better.
The Mr Gasket 6856G valve covers look like 70's hot rod parts... similar to the Micky Thompson valve covers on my last smallblock. There are a lot of those style valve covers out there.

Gregski 12-15-2018 07:33 PM

Re: Restoring Rusty
 
1 Attachment(s)
well Gentlemen and Ladies the circus continues

with the taller valve covers we now had heater hose interference as the hoses were resting on the valve covers and pressing against the hard line fuel rails - presenting us with a dilema of epic proportions

we decided to throw money at the problem and blew a ridiculous amount duckets on fittings and hose cutters (to the tune of $90 bucks maybe) the hose cutters we got at Home Depot and oh man worth every penny, the guy at the fittings and hoses specialty shop was super kind and recommended I try a home improvement store instead of an auto parts store for the cutters in order to save some money so I got them for half the price they are technically PVC cutting thingies, so so so nice straight cuts every time

Gregski 12-15-2018 07:34 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by hatzie (Post 8406123)
With the Vortec heads I think I'd consider the center bolt valve covers. They seemed to seal better.
The Mr Gasket 6856G valve covers look like 70's hot rod parts... similar to the Micky Thompson valve covers on my last smallblock. There are a lot of those style valve covers out there.

I ditched the Vortec heads brother cause all three or four pairs I got from the junk yard were cracked. These are standard outside bolt pattern aluminum heads.

Gregski 12-15-2018 07:44 PM

Re: Restoring Rusty
 
4 Attachment(s)
and here is the fruit of my labor, I have yet to fire it up to see if it will leak, one disappointment at a time though, ha ha

I am very pleased how it turned out and quite proud of that rubber hose pedistal idea off the alternator bracket, zip tie action at it's finest [Roadkill would be proud]

Gregski 12-15-2018 07:59 PM

Re: Restoring Rusty
 
1 Attachment(s)
as the Dominos were falling and I'm sure you all can relate, you want to change one thing and end up changing 7

I decided to ditch the dual hard carburetor fuel line, for two reasons

1. it defeats the wonderful modular design of the Holley carburetor, more specifically it prevents you from rejetting the carb by only removing the front float/fuel bowl since now the front and rear bowls are joined by this metal aparatus with no give in it

2. in my case the hard line was literally resting / pressing on the 5/16th heater hose line (not sure if that is the supply or the return, I think that's the return line) where it was connected to the fitting going into the intake manifold

we are going to run a DIY 3/8th rubber fuel line solution instead with ample bendability

Gregski 12-15-2018 08:06 PM

Re: Restoring Rusty
 
3 Attachment(s)
this is where we start taking one step forward and two steps back

that hard fuel line was such a P.I.A. that I had to lift the carburetor up in order to get the 5/16th heater hose off the fitting on the intake manifold

well as I did that I tore the carburetor gasket, we couldn't have that, so I removed the carb and was rewarded with the ugliest gasket sticability factor I have ever dealt with on a carb, I mean this thing was damp for some reason and came off in dime sized pieces if not smaller, there went 2 hours of my life with a razor blade I will never get back

and how about that rusted up passage, not sure what it is for but clogged up like that can't be good

Gregski 12-16-2018 01:53 AM

Re: Restoring Rusty
 
4 Attachment(s)
so a few final updates for the day and it was a busy day, got it about 99% done

I want to share what I learned about carb fittings because I was truly in fittings hell trying to convert from the hard lines back to rubber lines, apparantly you can't just go to the Auto Parts store and get a NPT 3/8th barb fitting and screw it in to your carburetor, oh no

I'm sure there are many ways to do this, but I like the way I did it as it eliminated some extra hardware, in particular these inverted 7/8-20 to 5/8-18 intermediate buggers

here I show one from the front and the other from the back so you can see how they look

Gregski 12-16-2018 01:59 AM

Re: Restoring Rusty
 
4 Attachment(s)
I found these Mr Gasket Inlet Fittings for a 3/8ths hose with the large 7/8-20 thread which allows them to screw right into the carb bowls without those intermediate buggers from before

and of course I didn't use any tape on those threads, ha ha

Gregski 12-19-2018 10:25 AM

Re: Restoring Rusty
 
2 Attachment(s)
presenting the Roadkill Repair [Starter] Kit

"If you can't find the right tool in this garage Mr Arizona, you don't belong near a car."

Palf70Step 12-19-2018 02:39 PM

Re: Restoring Rusty
 
So True!

Gregski 12-20-2018 01:28 AM

Re: Restoring Rusty
 
I am giving this update to my brothers and sisters who found themselves at one point going 55 MPH in reverse like me the last couple of days, man it's been ruff, nothing was going The Greg's way

I got to the point where all I had to do is tighten that last 3/8th inverted flare fitting in the fuel pump and take the truck for a test drive, but and you can already see where this is going

but even though I used that two wrench technique to hold the coupling that's welded to the fuel pump while twisting the fitting into it, I still managed to ever so slightly twist the darn thing, which you guessed it caused a massive fuel leak


so I was crushed, it was late at night and I decided to walk away....

Gregski 12-20-2018 01:31 AM

Re: Restoring Rusty
 
3 Attachment(s)
realizing I need to replace the fuel pump anyway I thought why not give an electric one a go, so I went out and got the Mr. Gasket #12S (it being for the 8 bangers)

I mean how hard could it be?

being a simple man I opted out for a simple basic two wire gitty up, black wire (ground) goes to the frame, red wire plus 5 AMP fuse goes to the fuse panel key on slot

Gregski 12-20-2018 01:33 AM

Re: Restoring Rusty
 
1 Attachment(s)
X marks the spot

well this is where it went, I need to take a pic with it installed, it got too dark and I already lowered the rig

Gregski 12-20-2018 01:38 AM

Re: Restoring Rusty
 
2 Attachment(s)
"Sometimes God's greatest gifts are unanswered prayers" thank you Garth I couldn't have said it better myself

well not exactly but that leaky fuel pump was a blessing in disguise, since after I pulled it off I saw this...

gentlemen/ladies let me be blunt... WE FOUND THE EXHAUST LEAK !!! LOL

that's right, a set of stock exhaust manifolds, two sets of headers, and God only knows how many different exhaust gaskets and two/three years later, what I swore sounded like an exhaust leak, clickitty clockin' noise was this darn busted fuel pump rod spring thingie

Gregski 12-20-2018 01:44 AM

Re: Restoring Rusty
 
TEST DRIVE

Oh my goodness I am now hearing noises rattles and squeaks that I didn't know existed, and I mean it in a good way, I may even be hearing "Road Noise" lol, Honda style, jk
  • No more transmission noise
  • No more engine noise
So how is the electric Mr. Gasket fuel pump? well Mopar Seth insisted that it will be noisy, well it ain't, now I may not have the quietest mufflers on the block, ha ha, but still I don't hear any fuel pump noise, the one CON I have is that it aint no 3/8ths fitting on either end, they are more like 5/16ths so you gotta crank down on those hand cutting hose clamps to get the hoses snug

I only driven it around the block and then to the gas station, so I still need to take it on the freeway, and i will report back, but for the time being, thumbs up for that little $40 dollar guy, complements of AutoZone

daddyjeep 12-20-2018 02:06 PM

Re: Restoring Rusty
 
I have a similar pump feeding my big block so I think you will be ok.

Gregski 12-20-2018 08:41 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by daddyjeep (Post 8409761)
I have a similar pump feeding my big block so I think you will be ok.

cool, is it also a Mr. Gasket brand?

hatzie 12-20-2018 10:11 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8409176)
TEST DRIVE

Oh my goodness I am now hearing noises rattles and squeaks that I didn't know existed, and I mean it in a good way, I may even be hearing "Road Noise" lol, Honda style, jk
  • No more transmission noise
  • No more engine noise
So how is the electric Mr. Gasket fuel pump? well Mopar Seth insisted that it will be noisy, well it ain't, now I may not have the quietest mufflers on the block, ha ha, but still I don't hear any fuel pump noise, the one CON I have is that it aint no 3/8ths fitting on either end, they are more like 5/16ths so you gotta crank down on those hand cutting hose clamps to get the hoses snug

I only driven it around the block and then to the gas station, so I still need to take it on the freeway, and i will report back, but for the time being, thumbs up for that little $40 dollar guy, complements of AutoZone

Looks like it's mounted back near where the dual tank valve would be located on an NL2 optioned truck. You mostly shouldn't be able to hear it run back there.

y5mgisi 12-20-2018 11:29 PM

Re: Restoring Rusty
 
Still one of my favorite threads.

daddyjeep 12-21-2018 02:05 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8410329)
cool, is it also a Mr. Gasket brand?

To be honest Gregski... I don't remember what brand I went with.

Gregski 12-21-2018 03:27 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by y5mgisi (Post 8410451)
Still one of my favorite threads.

thank you so much, the feedback died down a bit so Rusty was all like am I dumpin' all this oil on your driveway for nothin'? and I was like no bro, keep those leaks going so you can git a new enjin - If we build it they will come!

rusty76 12-22-2018 09:28 AM

Re: Restoring Rusty
 
Glad to see you got rusty back together. Sometimes we take a few steps back just to leap forward. New engine would be cool.

Gregski 12-28-2018 01:01 PM

Re: Restoring Rusty
 
1 Attachment(s)
WHEN YOUR FAMILY KNOWS YOU DRIVE A CHEVY... lol

Gregski 12-28-2018 01:04 PM

Re: Restoring Rusty
 
4 Attachment(s)
somehow I got off Santa's Naughty List this year, notice I didn't say I was nice... exactly, lol

Gregski 12-28-2018 01:09 PM

Re: Restoring Rusty
 
3 Attachment(s)
a couple years back I replaced my original '74 old and tired gauges with '78 style (electric oil pressure rather than mechanical, etc.) brand new ones. Yet it was still 40 year old technology, so there is no time like the present, (get it I said "present" ha ha) I mean electronics work makes for a great winter project, as there is no crawling on your back (usually) or getting coolant or oil all over yourself during winter time

so we will be replacing the brand new OEM Speedo and Tach with the brand new DIGITAL [pronounced] "super awesome and incredibly easy to tune, with additional goodies"

join me why don't you

Gregski 12-28-2018 01:33 PM

Re: Restoring Rusty
 
2 Attachment(s)
a parting look at the ol' setup

honestly the straw that finally broke the camels toe on these gauges was that one of the turn indicator lights went out, I forget which side, but I was running a brand new circuit board and I spent $7.5 million dollars on all new bulbs, and it did me dirty like that, so I'll show you Rusty...

Palf70Step 12-28-2018 01:51 PM

Re: Restoring Rusty
 
Love the tach. But yeah, these gauge pods sometimes will try your patience, especially that circuit board thingie.

Gregski 12-28-2018 04:17 PM

Re: Restoring Rusty
 
2 Attachment(s)
Mandatory Stare and Compare

Old Gauges vs The New "Summit" aka Intellitronix ones

man I totally forgot the new ones are that much smaller, but hey, why in the world would we expect an exact fit (it's like buying replacement shower tiles at Home Depot 10 years after your house was built, ain't gonna happen) lol

Gregski 12-28-2018 04:19 PM

Re: Restoring Rusty
 
4 Attachment(s)
note the Speedo on the left requires this Gizmotron to convert mechanical speedo gear output into electronic current

it's also funny how Summit is like all, yeah digital speedo $5.00 dollars, special drive unit... $100.00 dollars, ha ha

Gregski 12-28-2018 04:23 PM

Re: Restoring Rusty
 
2 Attachment(s)
so let's see if we can make these Intellitronix gauges work, man so close...

Gregski 12-28-2018 04:28 PM

Re: Restoring Rusty
 
5 Attachment(s)
... and then this happened,

what? you didn't expect this to be easy?

I swear I didn't drop it or nothin' it just came apart in my hand, and it looks like the back of that plexi glass still has the backing paper so they didn't finish building / gluing it, I guess some factory worker was late on his Christmas shopping and decided to leave early that Friday afternoon, lol

Q/A be dammned!

Gregski 12-28-2018 06:01 PM

Re: Restoring Rusty
 
5 Attachment(s)
alright, you guys didn't really buy that story that I tore the dash apart due to a faulty turn signal light did you?, sure that was the final straw, but the bigger issue was the most annoying clutch pedal squeaking sound ever, that's right we fix the transmission, and Rusty says OMG, must make other annoying noise, and oh boy did he deliver

and once again DORMAN lets me down, if you recall we rebuilt the entire pedal assembly real nice painted it and all and even shoved new plastic bushings in it no more than two years ago, even greased it up with white lightning grease (I'm looking at you Hatzie) that took two weeks to ship cross country, ha ha, and once again the original bushings lasted 40 years the new flimzy ones two!!!

and of course Rusty drew blood on that garage door like spring removal off the clutch pedal, those of you with manual transmission are nodding your heads right now I bet, that spring could kill a medium sized horse

hatzie 12-28-2018 10:58 PM

Re: Restoring Rusty
 
That's miserable... What did Dorman use to make the bushings?
Can you turn some new ones out of bronze or brass?

Palf70Step 12-29-2018 09:33 AM

Re: Restoring Rusty
 
Those springs definitely keep you on your toes. I had a very similar mark from my 64 when I did the clutch and tranny.

Gregski 12-29-2018 11:31 AM

Re: Restoring Rusty
 
1 Attachment(s)
Quote:

Originally Posted by Palf70Step (Post 8415334)
Those springs definitely keep you on your toes. I had a very similar mark from my 64 when I did the clutch and tranny.

it seems the trick is to allow the pedal to come all the way forward, but to do that I had to remove that long pivot bolt, so who knows what gives in that contraption


All times are GMT -4. The time now is 11:42 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com