The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=4)
-   -   Restoring Rusty (https://67-72chevytrucks.com/vboard/showthread.php?t=645440)

Gregski 06-23-2018 09:35 AM

Re: Restoring Rusty
 
1 Attachment(s)
so $217 dollars later (yes more than what we paid for the transmission in the first place) see lesson #1 above, ha ha we had ourselves what we believe is a proper or more better transmission mounted shifter linkage - this one I was told came out of a Chevelle

Gregski 06-23-2018 09:57 AM

Re: Restoring Rusty
 
2 Attachment(s)
and this is what the shifter bits looked like when they arrived, can't wait to bolt them on and give them a go shiftin gears

hopefully they don't position the shifter too far back where we have bench seat clearance issues

kinda cool that the eBayer threw in that white shifter ball, I happen to have a shifter stick that I hope will work so this should give me everything I need

Gregski 06-23-2018 10:01 AM

Re: Restoring Rusty
 
1 Attachment(s)
Saginaw Specifics

When looking at a Saginaw transmission, the front input shaft will likely have one or multiple grooves cut around its diameter. These grooves are there to indicate the ratios of the gears inside the transmission.

0 grooves: First 2.84, Second 2.01, Third 1.34, Fourth, 1.00

1 groove: First 2.54, Second 1.84, Third 1.44, Fourth, 1.00

1 groove: First 2.54, Second 1.84, Third 1.32, Fourth, 1.00

2 grooves: First 3.11, Second 2.20, Third 1.47, Fourth, 1.00

3 grooves: First 3.50, Second 2.46, Third 1.65, Fourth, 1.00 (I believe ours has three grooves so it's this one)

rusty76 06-23-2018 09:01 PM

Re: Restoring Rusty
 
This ought to be fun. I’m watching. I know you are ready to cruise a new four speed.

Gregski 06-24-2018 06:39 PM

Re: Restoring Rusty
 
1 Attachment(s)
so decided to clean the Saginaw four speed transmission a bit, using Mineral Spirits from Home Depot, a wire brush, and some paper towels

Gregski 06-24-2018 06:41 PM

Re: Restoring Rusty
 
2 Attachment(s)
remember our goal being: Progress Not Perfection

Gregski 06-24-2018 06:43 PM

Re: Restoring Rusty
 
1 Attachment(s)
and here it is with the Hurst four speed shifter linkage mounted and my old chrome HURST shifter installed, not sure if this stick will work/clear but we shall see, it does look pretty cool though

of course couldn't mount the white ball do to thread differences not only size but also pitch, coarse vs fine, it's not easy fellas, really wanted to see that ball atop the stick

Gregski 06-24-2018 06:53 PM

Re: Restoring Rusty
 
1 Attachment(s)
When looking for a brand new Hurst shifter components I further learned there were two Saginaw transmission types the 441 and the 456.

Hurst makes linkage for the 441 but not for the 456. So naturally I believe I have the 456, lol. Though with that Chevelle style bracket I think it makes it a moot point as to which one I have the 441 vs the 456 as it mounts the shifter using the bracket and ignored the holes in the tailshaft.

hope you is following all this it can get unnecesarily complicated

and I still don't get how this is supposed to be a torque tube transmission as it accepts a regular Turbo 350 yoke and has a rear seal for an open shaft, but the graphic saying it could be off of a 1981-82 Camaro or Firebird makes me feel a bit warm and fuzzy inside

hatzie 06-25-2018 10:39 AM

Re: Restoring Rusty
 
The F-body torque tube mounts to the three holes on the bottom of the tailhousing.

Gregski 06-26-2018 01:15 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by hatzie (Post 8288515)
The F-body torque tube mounts to the three holes on the bottom of the tailhousing.

thanks bud anyway you can help me find a pic of one, I can't seem to find it on the Google, ha ha

brakenit 06-26-2018 01:36 AM

Re: Restoring Rusty
 
1 Attachment(s)
Quote:

Originally Posted by Gregski (Post 8289000)
thanks bud anyway you can help me find a pic of one, I can't seem to find it on the Google, ha ha

He meant torque arm, 3rd and 4th gen f-bodies had a torque arm suspension. C5 and newer Corvettes have a torque tube.

A bushing bolts to the tail housing of the transmission and then a link connects the rear axle to that bushing to control axle rotation. It's basically a type of 3 link suspension.

Looks like the Vega had a torque arm suspension as well.

I found this picture here.

http://dave.h-body.org/H-body%20Conversion%20Tips.htm

Gregski 06-26-2018 01:59 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by brakenit (Post 8289005)
He meant torque arm, 3rd and 4th gen f-bodies had a torque arm suspension. C5 and newer Corvettes have a torque tube.

A bushing bolts to the tail housing of the transmission and then a link connects the rear axle to that bushing to control axle rotation. It's basically a type of 3 link suspension.

Looks like the Vega had a torque arm suspension as well.

I found this picture here.

http://dave.h-body.org/H-body%20Conversion%20Tips.htm

Thank you, aha, I appreciate that, but there's a big difference between a torque tube and a torque arm. I can buy into the torque arm setup, the torque tube as you pointed out I only knew of one modern car that had it that being the Corvette, the older Chevys may have had it but those may have been pre War cars or 50s.

brakenit 06-26-2018 02:23 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8289013)
Thank you, aha, I appreciate that, but there's a big difference between a torque tube and a torque arm. I can buy into the torque arm setup, the torque tube as you pointed out I only knew of one modern car that had it that being the Corvette, the older Chevys may have had it but those may have been pre War cars or 50s.

I agree, I don't understand why your graphic says torque tube since that should refer to some type of enclosed driveshaft which no Camaro ever had.

Gregski 07-05-2018 03:28 PM

Re: Restoring Rusty
 
1 Attachment(s)
it's that time of year again Comrads, haha

MikeB 07-05-2018 05:26 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8287289)
Saginaw Specifics

When looking at a Saginaw transmission, the front input shaft will likely have one or multiple grooves cut around its diameter. These grooves are there to indicate the ratios of the gears inside the transmission.

0 grooves: First 2.84, Second 2.01, Third 1.34, Fourth, 1.00 (I believe ours has zero grooves so it's this one)

1 groove: First 2.54, Second 1.84, Third 1.44, Fourth, 1.00

1 groove: First 2.54, Second 1.84, Third 1.32, Fourth, 1.00

2 grooves: First 3.11, Second 2.20, Third 1.47, Fourth, 1.00

3 grooves: First 3.50, Second 2.46, Third 1.65, Fourth, 1.00

And the one with the tallest first gear (2.54) can handle the most torque. That's the ratio our trucks used for 350s with 3-speed manual trans.

The 3.50 first gear was used behind small six cyl engines, like the 250. Your 2.84 is probably right on the ragged edge for a 350, but I know you're a conservative driver. :)

rusty76 07-05-2018 08:33 PM

Re: Restoring Rusty
 
Is that a current pic of Rusty? Man what happened to the hood? I still like seeing you taking Rusty camping.

Gregski 07-05-2018 10:46 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by rusty76 (Post 8294956)
Is that a current pic of Rusty? Man what happened to the hood? I still like seeing you taking Rusty camping.

yes current pic, used wrong acid, muriatic instead of phosphoric to clean it, broke my heart when the rust came back, got second hood, will paint it instead, the rusted one is also tacoed

peace and chicken grease,
g

Gregski 07-11-2018 03:20 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by MikeB (Post 8294827)
...but I know you're a conservative driver. :)

ha ha, yup, I almost chocked on my beer when I read that, sure thing I'm a super hypermiler, lol

Gregski 07-11-2018 03:25 AM

Re: Restoring Rusty
 
3 Attachment(s)
Rusty treated me to some scary transmission noises on the way to work this morning to where I had to limp it home after work. So I decided to open up Midnight Auto and go Def Con 4 on the ol' OD trans!

I lifted the truck up to the highest click on the Harbor Freight 6 ton jacks and went to town

at nearly 10 PM it was still almost 80* F

Gregski 07-11-2018 03:29 AM

Re: Restoring Rusty
 
4 Attachment(s)
How does a one man with a bad elbow git the trans out by himself without a proper transmission jack you ask?

Introducing the Semi Fully Adjustable TransJack 3000... suitable for the semi amateur casual transmission swapper

brought to you by Pollack Potrafi (TM)

Gregski 07-11-2018 03:31 AM

Re: Restoring Rusty
 
3 Attachment(s)
and two short hours later she was out

Profanity Disbursement = Minimal

Gregski 07-11-2018 03:35 AM

Re: Restoring Rusty
 
4 Attachment(s)
mandatory stare and compare of the GM New Process NV833 and the Saginaw 4 Speed

hard to tell from the pics but they is nearly identical at roughly 21 5/16 inches long from bell housing to tailshaft end

Gregski 07-11-2018 03:37 AM

Re: Restoring Rusty
 
2 Attachment(s)
doing my best here to hold the squigly measuring tape with one hand and snap the pic with the other

MikeB 07-11-2018 09:34 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by Gregski (Post 8298832)
I lifted the truck up to the highest click on the Harbor Freight 6 ton jacks and went to town

Can't tell you how awesome these 12-ton stands are. I've never had to extend them past half way up. Just trying to spend your money. :)

https://www.northerntool.com/shop/to...hoCUsUQAvD_BwE

https://www.northerntool.com/images/...20_700x700.jpg

Gregski 07-11-2018 10:35 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by MikeB (Post 8299338)
Can't tell you how awesome these 12-ton stands are. I've never had to extend them past half way up. Just trying to spend your money. :)

https://www.northerntool.com/shop/to...hoCUsUQAvD_BwE

https://www.northerntool.com/images/...20_700x700.jpg

me want


All times are GMT -4. The time now is 07:40 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com