72 C10 parts
 

I need to clean out the garage, I have items from a 72C10 project. Items came from a truck with 350 Sbc and sm465 transmission. Truck was a California truck, items are in good condition.
Any members in Minnesota need any of these items, they are for sale for local pickup only at this time.
Items are also for sale locally on Craigslist and Facebook marketplace.
Perhaps in the future I can figure a way to ship items, if there is interest

Items offered for free are local pickup only, unless you are willing to pay shipping.
(Send me a Ups label, or pay USPS flat rate, if it will fit in the medium or large box)
If you are not a member, here’s an incentive, become a member, and perhaps get some free stuff.
Of course items offered are first come first served
In the pictures are:

Bell housing with bolts and mounts, and modified transmission crossmember (bell housing has some damage in the starter area, that does not affect mounting or operating) $50. New price $45 Reduced…now $35
Non A/C heater box, with controls, cables, blower motor, heater core $125. New price $115. Reduced… now $100 SOLD
Battery tray $30 SOLD
Various fuel and vent lines and sending unit $20 Free to member, local pickup.
Disk brake dust shields $35 New price $30
Stock height disk brake spindles $55 New price $50
Windshield washer reservoir and mounting bracket $25
Charcoal canister and mounting bracket with hoses $40 New price $35
Dual horns and relay,( I believe the wire harness is for the horns) $30 SOLD
Exhaust hanger $5 Free to member Claimed by member on 5/26/23
Aftermarket replacement exhaust manifolds $35 New price $30 SOLD
2 piece driveshaft with carrier bearing for LWB $100 New price $95 SOLD
Speedometer cable $5. Free to member Claimed by member on 5/26/23
Z bar, upper push rod, lower push rod, push rod nut, frame bracket, engine side Z bar bracket with ball stud, heavy duty clutch assist spring, with pin that bolts to clutch pedal, and a few small related pieces $100 SOLD
Master cylinder and booster with proportioning valve for disk/drum, with brackets $115 New price $105 SOLD
I have a set of Precision, glue on door seals, used 1 season, very good condition (went with press on seals). Free to member Claimed by member on 5/26/23

I also have a few items from a 68 GMC
Parking brake/E brake lever $25 (Sent to member on 6/30/23)
Fan blade (from 305 V6) $10. Free to member
Heat riser $5 Free to member

Re: 72 C10 parts
 

If ever you ship I’ll take the clutch items . Thanks much

Re: 72 C10 parts
 

I'm interested in the dual horns, relay, and harness if they work

Re: 72 C10 parts
 

Yes, both horns work, I tested them about a week ago.
If you want them, I can set them aside for you
Let me know if you want to pick them up, and I will get you my address and phone number
Thanks

Re: 72 C10 parts
 

I have had some interest in the clutch parts locally, but if no one shows with the cash, I could investigate the shipping and payment options.
Thanks for your interest

Re: 72 C10 parts
 

Okay thanks .
I can a send a ups label if ever we ship to avoid getting quotes

Re: 72 C10 parts
 

Whereabouts in Minnesota are you located?
Thanks
Posted via Mobile Device

Re: 72 C10 parts
 

Pine City, is located East of St. Cloud about an hour.
Located roughly an hour north of Twin Cities on 35, or roughly an hour south of Duluth.
My house is about a mile from 35

Re: 72 C10 parts
 

Ok, yes. I can pick them up this weekend, Saturday. I work until noon, but can head that direction afterwards, as long as the snow isn't too terrible...

Re: 72 C10 parts
 

Ok, let me know Saturday morning, depending on how the storm tracks.
I will PM my address

Re: 72 C10 parts
 

Thanks for your interest, and offer to help.
I think nightmare is going to take the horns , local pickup.
If after the weekend, nobody has bought the dust shields locally, and you still want them, I would consider shipping them.

I have never shipped items, and don’t have any experience receiving money through PayPal.
I willing to try/learn.
I don’t have a lot of time to get quotes.
I probably should have a small scale, not sure how accurate they are for shipping though.
I also could go to the post office and check on the flat rate “if it fits, it ships” boxes, but those are typically expensive to use and could cost more than the part in some cases.

A few members such as yourself, have mentioned sending a prepaid shipping label, that would help I think. To do this, do you need a size and weight of the package first?

Sorry for the long commentary and questions, just trying to figure out how to accomplish the buying and selling online process. And make sure members get the parts they want without added Grief from my lack of experience .

Re: 72 C10 parts
 

PM sent

Re: 72 C10 parts
 

Horns, harness, and relay, SOLD
Thanks nightmare for your purchase

Re: 72 C10 parts
 

It was a pleasure meeting you, and thank you.

Re: 72 C10 parts
 

Pm sent

Re: 72 C10 parts
 

Pm sent

Re: 72 C10 parts
 

Throwing a pm your way . . .

Re: 72 C10 parts
 

Clutch Zbar, linkage, and related items Sold to Tmend
Ups pick up today
Thank you

Re: 72 C10 parts
 

Received, and reply sent

Re: 72 C10 parts
 

I'm interested in the exhaust manifolds do they come with the bolts to bolt them on

Re: 72 C10 parts
 

I’m not sure if I have any exhaust manifold bolts. It’s possible I have some in a parts bin in the garage, but I can’t guarantee it.
Here are a couple of better pictures of the manifolds,

I see they want to load upside down, and I even tried rotating them…..

Re: 72 C10 parts
 

Reply and address sent.
Let me know if it wasn’t received and I’ll resend it, my internet has been lousy today.

Re: 72 C10 parts
 

Is the windshield reservoir mounting bracket set still for sale?

Re: 72 C10 parts
 

Yes it is

Re: 72 C10 parts
 

Any damage to bottle?? Thank you.