Re: Restoring Rusty
The primitive tool for the valve springs.. Holy. Ive been graced with having a pneumatic valve spring compressor, and thought the hand powered lever action ones were primitive haha good work man. Cant wait to hear it running again
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
The umbrela seal is like this
http://www.jegs.com/images/photos/20...249-504-16.jpg The others are viton seals and look like this http://static.summitracing.com/globa...-514-12_ml.jpg Watch where you place the longer arm on the tool it should be on the lower coil side of the spring that will give you the most "compression" of the spring also a magnet helps get the locks out if they are caked in there from years of abuse |
Re: Restoring Rusty
Quote:
DIY Head Porting Small Block Chevy Vortec 062 Part 1 of 3 |
Re: Restoring Rusty
4 Attachment(s)
Quote:
|
Re: Restoring Rusty
Quote:
When you put your gasket onto your heads and or intake manifold you will see just how bad the castings and how much material can be removed. |
Re: Restoring Rusty
The L 5 3 on the back of the block and also similar on the heads is the casting date. The 010 is the casting number for the block. The numbers on the head surface pad is what makes it specific for your truck. The left number should match your vin. The number on the right is prefix code that tells where and when it was assembled and what exactly it was power wise.
Word of caution on those heads, the vortec heads are known for cracking. It would be a good idea that you have the heads magnafluxed for cracks. The surface on them also is very crude. You really need a very true and flat surface. I would highly suggest a visit to your local machine shop. Having things done now is a lot cheaper then being bent over the fender doing it a second time. This is not my shade tree opinion then is my machinest opinion. I have seen more then my fair share of them. You have a great build thread going on just read thru it, keep it up love a budget build. Great save on an old truck. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Just ready your whole thread fun read. Make sure to replace those steel freeze plugs with brass while the engine is out!!! Subscribed
|
Re: Restoring Rusty
Quote:
Today I went in to a different AutoZone on my way home from work, and they too only had one brass freeze plug, so I bought it. It's not easy! lol |
Re: Restoring Rusty
Quote:
On a serious note, the main reason why I don't intend to port these Vortec heads is that everyone claims they are possibly the best GM cast iron heads, well so lets compare apples to apples. My non ported non polished 882s to these non ported non polished 062s. See how I did that? See how I just got myself out of doing more work, ha ha |
Re: Restoring Rusty
4 Attachment(s)
Quote:
Basically the holes of the Vortec head and the holes in the Mr. Gasket gasket do not match up, in other words they are not the same exact size. I wonder how much of that bottom 3/16ths of meat could you grind down before hitting a water jacket, or is there even a water passage below the exhaust port, honestly I don't know, and I'm too skierd to find out, ha ha |
Re: Restoring Rusty
4 Attachment(s)
and here is how the Mr. Gasket gasket holes match up with the HOOKER 2452 Competition header holes. Pretty good, but maybe they could use a little grindage also, but its risky, as you could cut through the weld and there are thinner walled pipes behind there.
|
Re: Restoring Rusty
5 Attachment(s)
Gentlemen riddle me this:
What are these two small threaded holes for in the back of the engine block one behind each cylinder head? |
Re: Restoring Rusty
Silly Greg I wasn't talking about that side lol. I was talking about intake manifold sides.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Greg, do not remove any material from the bottom/floor of the exhaust port. Doing so will actually hurt flow.
Felpro 1444 fits the stock Vortec exhaust ports well. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
5 Attachment(s)
got the driver side cylinder head all cleaned up just need to disassemble it next to clean the valves, I think it cleaned up pretty good, the black spotting you see that's just black paint from when it was factory painted and not grease
|
Re: Restoring Rusty
2 Attachment(s)
just a little stare and compare at the way she looked when I got her and now after a short wire brush session
I should show a similar comparison of me before (clean) and after (dirty) after I transffered all the grease and grime from this head and on to myself |
Re: Restoring Rusty
4 Attachment(s)
got the crank pulley cleaned
|
All times are GMT -4. The time now is 08:12 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com