Re: Restoring Rusty
1 Attachment(s)
Quote:
|
Re: Restoring Rusty
Quote:
I actually converted the car from a perfectly good TH350 that some PO had installed many years before. I probably saved more than 100 lb including the weight of the trans, T/C, cooler, and fluid. Sold the trans, related parts, and B&M shifter for around $250 as I recall, which paid for a used bell housing and flywheel, clutch pedal kit, and new pressure plate and disc. So it was pretty close to a net zero$$ conversion. Wish I had more of those those projects.:( |
Re: Restoring Rusty
5 Attachment(s)
had a little time to show Rusty some love today, been meaning to install some loop hooks on the bed ever since I took off the rusty OG ones which were mounted on the outside (very practical not very asthetical) and we're all about form over function at Damage Inc. Garage
I tried to get these 3/8ths hooks on Amazon but finally got 'em at ACE Hardware - I think they was like .97 cents a piece so off with the two remaining old ones and on with the new six pack there were six holes already drilled on top of the bed rails so I just had to enlarge them slightly and I tapped them, I figure I would screw these hooks in from the bottom, decapitate the shafts that stick out, and welderize them to make the new owners life a little bit more exciting if he ever considers removing them, ha ha I doubled up on the nuts to make them hang a bit lower below the side lip |
Re: Restoring Rusty
5 Attachment(s)
as I was wire wheeling the zinctoniam off of the tip of the threads I considered painting them black, hewk powder coating even, but then I pushed those silly ambitious thoughts right out of my head ~ Porgress Not Perfection is the new black!
|
Re: Restoring Rusty
4 Attachment(s)
couple bird poops later, and the hooks were in
|
Re: Restoring Rusty
1 Attachment(s)
and with the hooks installed it was time to go fetch some lumber for our next project... Truck Doing Truck Things!
... and the hooks worked great! no problems to report, ha ha |
Re: Restoring Rusty
Two sweet projects at one time. Now I know there are no excuses.
|
Re: Restoring Rusty
"and welderize them to make the new owners life a little bit more exciting if he ever considers removing them, ha ha"
So am i reading this right? Rusty is looking for a new home? |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
As for your bench seat, you wouldn't have to sew anything and still do it yourself. You've done everything else, surely buying a premade cover and using hogring plyers isn't too intimidating :) Might have to replace some broken springs and repair or replace some foam, but its all available out there.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
I wish I would of thought to install those eyelets like that on mine !!!
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
I'd ask TKCR about it and read her bench seat thread.
This is post 143 of that thread. http://67-72chevytrucks.com/vboard/s...&postcount=143 The second seat in that bunch would go well with your green interior. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
Heavy load ya got there! I did something similar with my last truck, but installed 3/8" stainless eye bolts in each corner of the bed floor, reinforced by a thick flat washer on the bottom of the bed. |
Re: Restoring Rusty
My mom always said that if I was too quiet, I was up to no good.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
What tangled webs we weave...
|
Re: Restoring Rusty
5 Attachment(s)
not funny !!!
this one sprung a pin hole leak right above the water line by the inlet on the driver side, I could hear it hissing under pressure when I tried to pump it up with a test pump (a total must have tool) but could not see any moisture coming out nor could I build up any PSI, even tried the Windex look for bubbles trick, so I got mad, yanked it out and tested it in my organic hydro radiator testing facility - and we saw tiny little bubbles, just enough to cause a small leak that would cause me to overheat once every two weeks or so (most of the time in the In N Out drive through, ha ha) 3rd brand new radiator in six years ! November 3rd 2016 installed Northern aluminum one off of AMAZON for $271, post #4983 December 16th, 2017 (only one year later) bought a Chinese plastic one called Rad Cool for $114 from a local mom and pop radiator shop, post #5333 and now this one from NAPA for $125 |
Re: Restoring Rusty
Hope it works I have to go to NAPA for a new one. I bought one for my 89 jeep 5yrs now maybe longer from NAPA and still good
|
Re: Restoring Rusty
1 Attachment(s)
Quote:
|
Re: Restoring Rusty
Guess I've been lucky. Around 5-6 years ago, I bought a "Murray" radiator that looks like yours from O'Reilly Auto Parts for around $130. Mine is the small one (17" x 28-1/4" x 1-1/4"), but it keeps my 355 below 190 deg even on very hot days. Looks to be the same thing as a "Spectra Premium" at Rock Auto for $104 + shipping.
Haven't had any issues with mine, but I bought it locally for the lifetime warranty if it does fail. |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
2 Attachment(s)
... and order in the Universe has been restored
the PCM now reads 192° F relying on the sending unit at the front of the driver cylinder head, aka the stock location and my aftermarked Intelitronix digital gauge reads 190° F relying on the sending unit in the back of the passenger cylinder head, as a backup location |
All times are GMT -4. The time now is 12:40 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com