Re: Restoring Rusty
3 Attachment(s)
this time I just got the Fel-Pro head gaskets, this is the passenger side old and new compared
|
Re: Restoring Rusty
1 Attachment(s)
I'm just reusing the old head bolts these aint no turkey to yield ones I don't think, I just lubed them up with the white thread stuff and called it good
|
Re: Restoring Rusty
2 Attachment(s)
so popped on the passenger side head and torqued her down to 65 foot pounds in three go arounds 30 - 45 - 65
|
Re: Restoring Rusty
1 Attachment(s)
driver side headbolts
|
Re: Restoring Rusty
1 Attachment(s)
driver side head gasket, these go on dry
|
Re: Restoring Rusty
1 Attachment(s)
went to torque down the driver side cylinder head and encounter a bit of a set back...
|
Re: Restoring Rusty
2 Attachment(s)
My trusy Craftsman torque wrench decided to give up the ghost after 20 years
|
Re: Restoring Rusty
4 Attachment(s)
so I went to Sears I mean its a Craftsman they should replace it right? Wrong, they only replace torque wrenches for 1 year and if you have the receipt, now I sure hope the new one I bought for $75 bucks from them don't break in the first year, but it is made in China so you never know
|
Re: Restoring Rusty
2 Attachment(s)
so this is how I adjust the valves, I like this method because you do half than you rotate the engine once and do the other half
so put the #1 cylinder at top dead center and do the following valves notice you are not touching #6 at all |
Re: Restoring Rusty
2 Attachment(s)
then you spin the engine once to #6 top dead center and you do the remaining valves (the blue side of the white board)
you do not touch #1 this time |
Re: Restoring Rusty
5 Attachment(s)
the intake manifold was up next, I honestly dread this part as I hate gooping the China Walls and making sure I lower the intake manifold properly aligned on to all that mess
so here I spray one side of the gasket with adhesive and let it set for a bit |
Re: Restoring Rusty
2 Attachment(s)
hey remember these? I never finished building up the flanges on the driver header, so here we go
got too dark outside to take a pic of the finished product |
Re: Restoring Rusty
4 Attachment(s)
Ah yes, the Troublesome Twins
it ain't pretty but it just might could work |
Re: Restoring Rusty
2 Attachment(s)
slipping the new Mr. Gasket crush gasket on the passenger side
|
Re: Restoring Rusty
2 Attachment(s)
slipping the crush Mr. Gasket gasket on the driver side
|
Re: Restoring Rusty
1 Attachment(s)
this time I set the engine on top dead center for #1 as I was assembling it that made dropping in the dizzy that much easier
|
Re: Restoring Rusty
1 Attachment(s)
carb goes back on along with the radiator and water pump hoses
|
Re: Restoring Rusty
2 Attachment(s)
fluids going in - you know that's a good sign
|
Re: Restoring Rusty
2 Attachment(s)
AND ALL BACK TOGETHER IN 72 HOURS!!!
but didn't get to start it cause I finished after 11:00 PM and it would have been way too loud!!! |
Re: Restoring Rusty
Nice job!
Craftsman isn't what it used to be...or maybe it is. I had a Craftsman electric impact that did it's job for a bunch of years. The ring that holds sockets on was always kind of a pita though and would stick one on or spit one off at random. When I was checking out junk at HF one day, I took a look at their impact and doggone it...except for the color it's exactly the same unit. So when the Craftsman crapped out, guess which one I bought? |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
I have that same 20 year old craftsman, mine gave up the ghost a year or two ago. A friend fixed the ratchet but instead of spending the money to get it recalibrated I use it as a breaker bar now.
Nice work as usual, hope this fixed the problem and gets Rusty on the dyno. Did you cut the header flange on the driver's side? |
All times are GMT -4. The time now is 01:12 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com