The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=4)
-   -   Restoring Rusty (https://67-72chevytrucks.com/vboard/showthread.php?t=645440)

Gregski 09-03-2018 08:01 PM

Re: Restoring Rusty
 
2 Attachment(s)
don't worry I used a piece of flat ply wood underneath not to dent or scratch da hood

Gregski 09-03-2018 08:04 PM

Re: Restoring Rusty
 
2 Attachment(s)
not too bad, I grounded the welds down a bit but not totally flat so that I wouldn't weaken the welds nor be unable to find them later if I needed to drill them out (that's my excuse anyway)

shot sum primer and ready for paint

Gregski 09-03-2018 08:06 PM

Re: Restoring Rusty
 
2 Attachment(s)
then it was on to the other side and the whole reason why we is doin' this in the first place

this side already developed a hairline crack in the safety fold, so I bugger welded it up

and just like on the other side we ground the surface to bear bare (?) metal prior to welding

Gregski 09-03-2018 08:09 PM

Re: Restoring Rusty
 
3 Attachment(s)
tell me if this has ever happened to you: with two spot welds left we ranned out of welding wire?

Gregski 09-03-2018 08:12 PM

Re: Restoring Rusty
 
2 Attachment(s)
but I wasn't gonna let this stop me, so I replaced the Lincoln .035 artillery with the .025 caliber (i.e. all that I had on hand) and grabbed the gun for the home stretch

I must say I like how the .025 lays down spot welds, now I'm sure if I knew how to fandangle the knobs on Big Red properly I could achieve the same results with the .035 but still the .025 agrees with me just the same

Gregski 09-03-2018 08:14 PM

Re: Restoring Rusty
 
2 Attachment(s)
since this project was sapposed to be done in August, with the paint still wet I hollered at my soon to be 17 millenial to come downstairs and help me flip this pancake over

we're gonna lossen up that surface rust with some 220 sand paper

Gregski 09-03-2018 08:18 PM

Re: Restoring Rusty
 
2 Attachment(s)
a little stare and compare, what a difference 5 minutes with the orbital sander makes

and then it was time for some Phosphoric acid treatment from Home Depot ($5.00, I'm looking at you $25 dollar Metal Re$cue), this is the potion I should have used the first time on my original hood, but I messed up and used muriatic acid instead (stupid me, should have paid more attention in Chemistry class)

Gregski 09-03-2018 08:46 PM

Re: Restoring Rusty
 
1 Attachment(s)
and here it is after the acid treatment and the baking soda neutralizing bath, man I wish the rest of the truck looked like this, I would just leave it, I like this [ahem] "patina"

Billy81 09-05-2018 10:37 PM

Re: Restoring Rusty
 
I am thoroughly impressed good sir

Gregski 09-06-2018 12:40 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by Billy81 (Post 8338276)
I am thoroughly impressed good sir

Thanks Billy, I'll be sure to let Joe Goodenuff know! ha ha

hatzie 09-06-2018 01:14 AM

Re: Restoring Rusty
 
1 Attachment(s)
Joe Goodenuff huh...
Attachment 1818527

Country705 09-06-2018 10:57 AM

Re: Restoring Rusty
 
Looks good thanks for the updates

rudyyloverboiii 09-08-2018 11:37 AM

Re: Restoring Rusty
 
gregski i enjoy ur build and the progress ur making.

U wouldnt happen to know anything about hooking up a 292 into a 700r4 do ya? Or perhaps guiding me in some direction?

Gregski 09-08-2018 06:14 PM

Re: Restoring Rusty
 
Quote:

Originally Posted by rudyyloverboiii (Post 8340112)
gregski i enjoy ur build and the progress ur making.

thanks

Quote:

Originally Posted by rudyyloverboiii (Post 8340112)
U wouldnt happen to know anything about hooking up a 292 into a 700r4 do ya? Or perhaps guiding me in some direction?

I'm sorry I do not, but have you seen this thread:

Installing a 700r4 behind a 292

D13 09-09-2018 07:57 AM

Re: Restoring Rusty
 
Still loving it Gregski. Curious though - what are you going to do with the A833? I understand why you might want a trans with closer ratios but are you going to rebuild it and store it?

Gregski 09-09-2018 09:55 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by D13 (Post 8340570)
Still loving it Gregski. Curious though - what are you going to do with the A833? I understand why you might want a trans with closer ratios but are you going to rebuild it and store it?

Yes I plan on rebuilding the A833 next month. I always planned on rebuilding it if for no other reason than to see it's guts and diagnose the problem. However since the Saginaw is making that dreaded gear noise in all but 1st & Reverse gears, it is coming out and the A833 is going back in.

I plan on trying 4.11 POSI gears so the A833 overdrive transmission makes more sense anyway.

And I would be lying if I was not trolling Craigslist for a MUNCIE M21

Gregski 09-09-2018 07:39 PM

Re: Restoring Rusty
 
2 Attachment(s)
so let's remember our mantra:

"Progress not Perfection!"

you all know how i love to use the white paper towels, however for final wipe before painting I prefer the blue ones cause they don't leave behind as much fuzz

Gregski 09-09-2018 07:42 PM

Re: Restoring Rusty
 
3 Attachment(s)
I like to stay within the same paint ecosystem ie, use the same brand primer, paint, and clear coat, and I happen to like that Krylon semi flat black so that dictates I use Krylon products, however Krylon didn't offer a black primer at Pep Boys so I went with this Dupa Color primer, and since we won't be using Krylon paint anyway, it really doesn't matter

I want to use black primer because that's what lurks beneath my factory green

Gregski 09-09-2018 07:45 PM

Re: Restoring Rusty
 
2 Attachment(s)
Remember: Safety Third!

please use a proper mask when spraying paint, YES even if you are painting outside

you know I always talk about how I like to use organic free range parts and materials, and I am sure you think I am joking or am simply nutz, well...

Gregski 09-09-2018 07:48 PM

Re: Restoring Rusty
 
1 Attachment(s)
I like the instructions on these cans, if you can find them amidst the stupid legal warnings, and are able to read the -12 size font, ha ha

two light coats followed by one medium coat, simple

so lets see how it does

What? That's it? Yes the purpose of the first light coat is simply to make the area tacky, that's all, that's it.

Gregski 09-09-2018 07:49 PM

Re: Restoring Rusty
 
2 Attachment(s)
... 10 minutes later we shot the second light coat

Gregski 09-09-2018 07:54 PM

Re: Restoring Rusty
 
3 Attachment(s)
and 10 minutes after that we shot the medium coat, which wasn't enough so we shot an additional medium coat 10 minutes apart

LT7A 09-11-2018 07:22 AM

Re: Restoring Rusty
 
1 Attachment(s)
Safety Thirst!

LT7A 09-11-2018 07:24 AM

Re: Restoring Rusty
 
Rusty is going to look great with the new hood! When do you start getting humidity issues with paint? And nicely done on the home-fab hood stiffeners. I folded a guy's hood for him at the Full Serve pumps at Chevron in the summer of '87...

Gregski 09-15-2018 10:22 AM

Re: Restoring Rusty
 
Quote:

Originally Posted by LT7A (Post 8342096)
Safety Thirst!

Um... I will handle the humor around here young man, is that clear! jk luv you bro


All times are GMT -4. The time now is 09:08 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com