Re: Restoring Rusty
5 Attachment(s)
decided this was as good a time as any to delete the charcoal canister, after all getting rid of it would also get rid of at least one of them three hard lines
and so I yanked it all out, including the long noodle evap hard line all in one piece, how impressive is that folks, JK |
Re: Restoring Rusty - Charcoal Canister Delete
3 Attachment(s)
now before we git into an argument why in the world would I remove the charcoal canister, lemme just say, betcha didn't realize it is hallow on the bottom?
ok, now lets have at it |
Re: Restoring Rusty
4 Attachment(s)
OK, with the evap fuel line removed and the others shoved out of the way got the passenger side long tube header installed
no major plug wire issues on this side like the #5 on the opposite side bottom A arm has plenty of clearance too |
Re: Restoring Rusty
I was looking things over in my 87 today and it looks to me like getting headers in there might be a pain. The motor mounts look like they will hit them. I was wondering about the legality of removing the emissions crap that goes into the manifolds. Since obviously the tubes in the manifold will be removed when you put the headers on it obviously the egr thingy will not be hooked up correctly. So, if you live in a state or area that requires emission testing will it pass? Being in California I am sure you have to deal with it.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
He had the EGR tubes in the manifolds, which are part of emissions, and the charcoal canister. I understand he doesn't have all the crap I have but I am just curious how the headers will effect the inspections.
|
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
I did not realize that. I might be heading to an area that requires inspections and if I am not mistaken they require them to have all the original emissions crap no matter the age. I would have pulled it all off if it weren't for this.
|
Re: Restoring Rusty
Gregski: What I did with the 5/7 and 6/8 wires is reverse the looming on them. I bring 5 off in the 7 loom and go down and forward, and bring 7 forward to the 5 loom and then go down and back. This is with the Hooker 2453 (for K trucks) so not sure if you can do the same thing or not.
In this pic, on the back looming hooks, you would think the wires would be 1-3-5-7 counting out from the valve cover, but they're not. It's 1-3-7-5. So the 5 wire comes off first, goes down then forward, then the 7 wire comes off, goes down and back. http://users.rcn.com/weyand/smalls/imag0732small.jpg |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty
1 Attachment(s)
had my two pipes exfoliated, at a muffler shop, $5 bucks to do both, I will give them my business again when I have a bigger job, very appreciative
got to watch how they did it, pretty cool machine, no idea how I could have given it that much force manually |
Re: Restoring Rusty - Header Bolt Set
1 Attachment(s)
had to pick up a Header Bold Set, basically shorter bolts since the headers are less bulky, and smaller heads, 7/16 instead of 9/16
|
Re: Restoring Rusty
3 Attachment(s)
after hours and hours of measuring, swearing, and trying different arrangements, in the end, cut 6" off the front side of the X with my trusty 4" angle grinder/cut off wheel and ran it the wider way, and 1 inch off the rear which I ran the shorter way
doing this as a one man circus act was NO fun! |
Re: Restoring Rusty - Headers Done
... after 14 long hours we were done !!! and by WE I mean the Royal We, lol so at 10:30 PM I fired her up for the first time... Note: This included picking kid up from school, going to the muffler shop, and the auto parts house. |
Re: Restoring Rusty - Headers Done
Quote:
real vroom vroom noises are the best. congrats man. |
Re: Restoring Rusty
speaking of that VHT paint I used on the headers, it says
After paint is completely dry it must be cured to substantially increase the durability of the finish and and enhance chemical resistance. Finish is not chemical resistant until cured. there are 2 ways to cure them, Off The Vehicle and On The Vehicle We focus on the On The Vehicle method.
allow me to translate that for you... [ahem] making a good header coating product is difficult, making a good header coating product in a ratlle can is impossible, but there is definately a need, and it can be very lucrative, so what if we make a mediocre product and put the onus on the car guy to screw things up by giving him ridiculous procedures first to read in fine print (cause we know no one does) and then to follow (again no one will) then if the results aren't what they expect, well they only have themselves to blame, heck maybe they'll even buy a second can to try it again |
Re: Restoring Rusty
now why do I need such a contraption when Rusty is a carburated, well you can tune a carburetor real good like if you know the exact precise air fuel ratio, so some day I would like to connect a permanent Air Fuel gauge and this way I will already have that provision[/QUOTE]
could you or someone explain what you are talking about here I've heard about these just not exactly sure of it |
Re: Restoring Rusty
1 Attachment(s)
Quote:
Narrowband only shows you Lean - Good - Rich states, where as a wideband displays the actual ratio number on a digital display ie 14.7 the one I plan on getting is a single gauge with two O2 (Oxygen sensors) connected to it. The O2 sensors get installed in the exhaust pipes after the exhaust manifolds or headers and before the catalytic converters if you got em. Since I have a V8 engine with dual exhaust I want one sensor in each pipe so that I can see how balanced my banks of cylinders are. Is one running rich while the other side is running lean for example. Here is one of the products, it is pretty expensive, this is not a cheap $20 dollar guage we are talking about here. INNOVATE DLG-1: Dual Lambda (AFR) Gauge Kit includes the DLG-1 gauge, (2) Wideband oxygen OČ sensors, (2) 8 ft sensor cables, LC-2 Wideband Controller, (2) OČ sensor weld-on bungs, Black/Silver bezel, Black/White faceplate, Serial program cable, & Installation manual. P/N: 3891 MSRP $399 http://www.innovatemotorsports.com/products/dlg1.php |
Re: Restoring Rusty
Ok so I've never seen the digital gauge like that reading both sensors, I'm guessing your going for more power and fuel efficiency with that setup.
you all ways do some cool stuff |
Re: Restoring Rusty
You can get FAR cheaper setups to use a Wideband. For example there is a company up in here in Canada that you can get the cabling and O2 sensor for $100 for one side. It obviously gets more expensive when you are running dual exhaust such as Gregg is as both sides need to be equal.
The funny thing is its a $300 part that you'll use once and then put it away because once your carb is tuned it should be pretty good forever. |
Re: Restoring Rusty
Quote:
check out this video https://www.youtube.com/watch?v=ZUfkn161k6U |
Re: Restoring Rusty
I watched the video, maybe I'm just old but it just looks like a gizmo.
no offense |
Re: Restoring Rusty
I've had a wide band on my truck for about 6 years. I'm using the Innovate LC-1. Once you have this new information, you'll never go back. If you feel a stumble, you can quickly look at the gauge and see 18:1; no wonder. And, like Greg, my truck sees big changes in elevation, and you can jet the carb correctly for where the truck is being used. And when I'm heavy towing, I make darn sure the ratio doesn't get lean under power.
I have an analog gauge with 270 degrees of sweep. I think this displays the information better than digital numbers because we're not talking about a super-steady reading. But being able to see both banks on a v8 would be good too. I might buy one of those for my suburban, as it has the dash hole ready for the gauge (told you I could never go back). Also consider that with a dual plane intake on a sbc, the carb is *not* feeding the left bank and the right bank separately. So the dual O2 gauge is still a blend of the total carb. |
Re: Restoring Rusty - Inner Fender Undercoating II
5 Attachment(s)
unhappy with the RUST-OLEUM Undercoating on the inner fender I decided to give the 3M product a shot
results = better, but not great, as you can see it sputtered some bigger drops here and there rather than being nice and uniform spatter, anyway I will try the SEM Undercoating 39523 next, its all about the learning process had to use the entire can which is a good single coat, cost was around $10 bucks |
Re: Restoring Rusty
2 Attachment(s)
a little before and after off the driver side inner fender, should be going back on maniana after the undercoating dries
|
Re: Restoring Rusty - Operation Tachometer
3 Attachment(s)
check out what I picked up on eBay back in February but was holdin' out on you, a gauge cluster with a Tachometer - $80 bucks I think, score, it even came with a wiring harness, however no small fuel gauge and the circuit board is toast
|
Re: Restoring Rusty - Gauge Cluster
2 Attachment(s)
I have discovered that if you want to keep the stock look the hardest thing to get is the blueish/greenish plastic housing for the gauges, there is a difference between the one without a tach and one with
In my case I am not just replacing a 1974 no tach cluster with a 1974 cluster with a tach, I wasn't able to find one of the same year I recon I have picked up at least a 1978 gauge cluster as that may have been the first year of the electronic oil pressure gauge, which it has below I highlight the physical differences in the gauge housing cluster thingie Top Pic - 1974 no Tachometer, Ammeter, Mechanical Oil Pressure (manual transmission) Bottom Pic - 1978 with Tachometer, Voltmeter, Electric Oil Pressure (bottom also happened to be automatic trans) |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - Operation Tachometer
Quote:
Do you if the small gas gauge will support duel tanks |
Re: Restoring Rusty
Quote:
|
Re: Restoring Rusty - Operation Tachometer
2 Attachment(s)
Quote:
|
Re: Restoring Rusty - Operation Tachometer
Quote:
|
Re: Restoring Rusty - Tachometer
3 Attachment(s)
One thing that surprised me is that the Tachometer is not like the other gauges, ie two or three studs sticking out of the back. The Tachometer comes with an appendage, it has a different form factor
I guess I just expected the tach to look like a speedometer, especially having seen all the modern aftermarket ones where they look like matching beer cans, know what I mean |
Re: Restoring Rusty
5 Attachment(s)
dang forgot I had all these drama build up pictures of the new (used) gauge clusters arrival, LOL...
|
Re: Restoring Rusty
2 Attachment(s)
ok so the Tachometer has a square butt, so why can't we just cut a square hole in our non tach housings and call it good?
Great question, and it's not like the Greg hasn't thought of it, he's been itching to put his dremel to good use, LOL It seems like someone at GM was tasked with making these cluster not interchengeable and has succeeded, you see we would also have to cut the printer circuit board and that's where things get a bit hairy since the Tach would go where the large Fuel Gauge lives here are the backs cloaked with their respected circuit boards for comparison so put those propane torches down and slowly back away folks... jk |
Re: Restoring Rusty - New Visors
4 Attachment(s)
say what do we have here?
did my baby brother finally drop off my Christmas present? Why yes he did, and just in time for my Birthday, LOL but Greg aint it May, why yes it is, apparently you don't have a younger sibling, LOL gotta love that LMC packaging |
Re: Restoring Rusty - Visors
4 Attachment(s)
now we thought you was painting all your brown interior black with that special interior upholstery spray paint?
well I was trying it out, but the visors were too far gone and broken, take a look |
Re: Restoring Rusty - Old VS New Visors
1 Attachment(s)
here are the old ones and the new ones side by side, I recon I will have to reuse and paint the pivot sticks since Santa didn't bring me those and I don't have another 5 months to wait, JK
|
Re: Restoring Rusty - Operation Tachometer
Quote:
|
Re: Restoring Rusty - Operation Tachometer
Quote:
|
All times are GMT -4. The time now is 03:10 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com