Frame question 1/2 ton vs 3/4 ton
I have a 1/2 ton long bed 4x4 and I was wondering if it's worth it to you upgrade to a 3/4 ton frame I have 3/4 ton axles and springs. Going to be doing some towing. Any thoughts or advice thanks
Joe |
Re: Frame question 1/2 ton vs 3/4 ton
I think the frames are the same on the 4x4 1/2 + 3/4 tons.
As far as towing it depends on where you draw the line. If its a ocasional 7000 pounds i don't see it worth the effort. If it is alot of towing, and closer to 9000 pounds then a 3/4 ton will be the ideal choice. |
Re: Frame question 1/2 ton vs 3/4 ton
The frames are the same.
What are the 3/4 ton differentials you have out of? |
Re: Frame question 1/2 ton vs 3/4 ton
I've never had a K20 but the C10 and C20 frames are not the same. The C20 is stamped from heavier gauge steel and has extra bracing.
|
Re: Frame question 1/2 ton vs 3/4 ton
Quote:
I guess I was repeating what I heard without knowing for sure myself. Thank you. |
Re: Frame question 1/2 ton vs 3/4 ton
Thanks y'all
Will be towing about 7000lb |
Re: Frame question 1/2 ton vs 3/4 ton
Found this in another thread:
½ ton 2WD: 6-1/32 x 2-1/2 x 5/32 ¾ ton 2WD: 6-1/8 x 2-17/32 x 3/16 One ton 2WD: 8-1/8 x 2-13/16 x 3/16 ½ ton 4WD 115” WB: 8-1/32 x 2-25/32 x 9/64 ½ ton 4WD 127” WB: 8-1/8 x 2-13/16 x 3/16 ¾ ton 4WD: 8-1/8 x 2-13/16 x 3/16 As you can see, even the ½ ton 4WD long bed uses the same size frame member as the one ton 2WD. 1960-62 frame ,measurements ½ ton 2WD: 5-15/32 x 2-1/4 x 1/8 ¾ ton 2WD: 7-3/16 x 2-3/4 x 3/16 ½ and ¾ ton 4WD: 7-13/64 x 2-3/4 x 3/16 |
Re: Frame question 1/2 ton vs 3/4 ton
Do the 63-66 4x4's really have a taller frame channel?
|
Re: Frame question 1/2 ton vs 3/4 ton
Thanks guys, looks like some good information for me and other members.
Hope to be doing my upgrades this summer. Thanks Joe 1963 chevy original k10 long bed fleet side |
Re: Frame question 1/2 ton vs 3/4 ton
Quote:
So, the 3/4 ton 4x4 frame is heavier than the 3/4 ton 2wd? |
Re: Frame question 1/2 ton vs 3/4 ton
That'll work perfect
I have a 63 K10 long bed so going by that chart I'll be fine, just need to install my 3/4 ton axles in springs Thanks all |
Re: Frame question 1/2 ton vs 3/4 ton
Could someone please verify that the frame for the 4x4's are actually 8 inches tall?
|
Re: Frame question 1/2 ton vs 3/4 ton
I can check tomorrow ,66 K 20 4x4 and let you know.
|
Re: Frame question 1/2 ton vs 3/4 ton
Confirmation: My 66 K 20 frame is somewhere between 8-8.25 measured from about the center under the cab. Didn't want to roll around in the snow to check further!
|
Re: Frame question 1/2 ton vs 3/4 ton
Thanks.
I wonder if they made the frame taller because a 4x4 may need to resist more twisting. |
All times are GMT -4. The time now is 07:46 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com