MT WTB NL2 tank

[jaybatta]

Looking for an NL2 tank and mounting bolts, possibly even sending unit if in operable condition. It’s the tank that has the filler neck through the upper bedside, not in the middle of the bedside behind the metal door. I’m in Montana.

[best view]

There’s a member here who’s name is uncle he had everything

[jaybatta]

Examples of the NL2 tank. NOT the same as the saddle tanks.

Thanks

[best view]

Nampa Facebook has a guy who has one

[Getter-Done]

I just acquired one of these tanks at a Swap meet last weekend.


Reason for this is a story in itself.

So, the tank I have is rusted beyond putting back in service.

The pattern is there for the Dimensions to fabricate a New one.

I acquired it to possible Machine the tank nuts on the bottom.

Then I searched the forum a Guy from Washington State is making them cheaper than I can get the material for them.

I still plan to make a set or 2.

I have a Question.

Are these Spacers in your Picture?
(That I circle these in blue.)

If so do you have the dimension for them?
If you can share that, That would be Great.

Thanks for sharing your Knowledge on these Tanks.

This picture below is the nut I have for a Pattern.

In the Blue circles, Are those Spacers?

[jaybatta]

Originally Posted by Getter-Done

I just acquired one of these tanks at a Swap meet last weekend.


Reason for this is a story in itself.

So, the tank I have is rusted beyond putting back in service.

The pattern is there for the Dimensions to fabricate a New one.

I acquired it to possible Machine the tank nuts on the bottom.

Then I searched the forum a Guy from Washington State is making them cheaper than I can get the material for them.

I still plan to make a set or 2.

I have a Question.

Are these Spacers in your Picture?
(That I circle these in blue.)

If so do you have the dimension for them?
If you can share that, That would be Great.

Thanks for sharing your Knowledge on these Tanks.

This picture below is the nut I have for a Pattern.
Attachment 2342285
In the Blue circles, Are those Spacers?
Attachment 2342286

They might have been before it was shipped to me. When I got it there was only one and it looked like a piece of clear rubber hose. They may have came off in the box, but me the moron did not look for the other 2 before hucking the box.
Next time I lay hands on the tank I’ll take a closer look and get back to you.

[jaybatta]

Originally Posted by Getter-Done

I just acquired one of these tanks at a Swap meet last weekend.


Reason for this is a story in itself.

So, the tank I have is rusted beyond putting back in service.

The pattern is there for the Dimensions to fabricate a New one.

I acquired it to possible Machine the tank nuts on the bottom.

Then I searched the forum a Guy from Washington State is making them cheaper than I can get the material for them.

I still plan to make a set or 2.

I have a Question.

Are these Spacers in your Picture?
(That I circle these in blue.)

If so do you have the dimension for them?
If you can share that, That would be Great.

Thanks for sharing your Knowledge on these Tanks.

This picture below is the nut I have for a Pattern.
Attachment 2342285
In the Blue circles, Are those Spacers?
Attachment 2342286

Wait here they are, they’re in rough shape, but appear to be spacers. I’ll try to get them separate and get you some dimensions.

[jaybatta]

Originally Posted by best view

Nampa Facebook has a guy who has one

Thank ya much!

[jaybatta]

Still looking for a tank. Have everything else now.

[Dieselwrencher]

Originally Posted by jaybatta

Still looking for a tank. Have everything else now.

I've got a couple from a 72 I'd have to dig out and make sure it's the same as what you're after.

[jaybatta]

Originally Posted by Dieselwrencher

I've got a couple from a 72 I'd have to dig out and make sure it's the same as what you're after.

That’d be awesome thanks Ryan

[richard2717]

Is this what you are looking for?



.

[jaybatta]

Originally Posted by richard2717

Is this what you are looking for?



.

Wooooo! Yes sir

[jaybatta]

Originally Posted by richard2717

Is this what you are looking for?



.

Willing to ship? Livingston Montana 59047

Is it dry? Any holes you can see? Still have the mounting carriage bolts?

Thanks

[richard2717]

I only have the tank. Tank appears in good shape inside. The one end of the tank outside had some scale buildup that I knocked off but it still appears to be ok. I will ship for costs but if it is like everything else lately it kills the deal. If you pm me your full shipping address I can get an accurate quote. here are a few more pics from a couple minutes ago. The one picture is my attempt to take one of inside the tank.

[67RS/SSx2]

Wow, that tank looks really good.

[jaybatta]

Today was a good day, found a template for the holes in the bed. Aldo made some new spacers and bought some more rubber insulators, as I call them to go in between the spacer and the 12” carriage bolt. Just need to find some more retaining nuts.

Side note, these washers original? They all have what looks like a bird with an f in the middle, maybe falcon?

[jaybatta]

..

[Getter-Done]

Nice

I would say those are original, Maybe someone can chime in that has them.

I was going to try to make some of these nuts that look Original.

There will be a lot involved and probably deem Unaffordable.

It can be done.

Those washers can be easily made.

[jaybatta]

Agreed on the washers, that’d be easy. The retaining nuts is another story.

I’m wondering the purpose of those spacers now. They don’t touch the bottom side of the bed floor like I thought they would. The bed supports won’t allow it.

[IronCanine]

Originally Posted by jaybatta

Today was a good day, found a template for the holes in the bed. Aldo made some new spacers and bought some more rubber insulators, as I call them to go in between the spacer and the 12” carriage bolt. Just need to find some more retaining nuts.

Side note, these washers original? They all have what looks like a bird with an f in the middle, maybe falcon?

I believe that makers mark is Falcon Forge from Shreveport, LA.

[Burnsy01]

Not to raid your post- but how many gallons are these tanks? I plan on building something similar for my diesel conversion for both sides of the truck

[67RS/SSx2]

Contact information for the machine shop I used is in post #29 of this thread.

https://67-72chevytrucks.com/vboard/...=834742&page=2

He did a good job and was easy to work with. He made some retaining nuts for others on this forum as well. He created a template from one of my good originals and likely still has that.

[jaybatta]

Ahhhh yes, I remember that now. I will reach out, thanks!