The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-19-2014, 05:30 PM   #1
npdunn
Registered User
 
Join Date: Sep 2008
Location: queen creek, az
Posts: 4
Drivetrain alignment and vibration

Hi there!

Need some help on the following:

I have a SWB 67, 2 wheel drive, 454 w/ 400 tranny.

Issue(s): the driveshaft is not centered through the crossmember (where the trailing arms are attached). I am just curious if it's supposed to be?? There is at least 1/4" difference when comparing each side.

My reason for concern is that I am getting an oscillating vibration starting at 50 mph and it stays no matter how fast you go. I have ruled out the following causes: driveshaft, u-joints, entire rear-end, tires/rims, tranny, flywheel, pinion angles.

My thought is: if the drive shaft should be centered through the crossmember, than the engine is sitting crooked- throwing off everything behind it. Which would also add another angle into the drive-train.

I am possibly stating the obvious, but I would like to get other's opinions.

Thank you for your help! I appreciate it.
npdunn is offline   Reply With Quote
Old 04-19-2014, 07:45 PM   #2
npdunn
Registered User
 
Join Date: Sep 2008
Location: queen creek, az
Posts: 4
Re: Drivetrain alignment and vibration

Quote:
Originally Posted by npdunn View Post
Hi there!

Need some help on the following:

I have a SWB 67, 2 wheel drive, 454 w/ 400 tranny.

Issue(s): the driveshaft is not centered through the crossmember (where the trailing arms are attached). I am just curious if it's supposed to be?? There is at least 1/4" difference when comparing each side.

My reason for concern is that I am getting an oscillating vibration starting at 50 mph and it stays no matter how fast you go. I have ruled out the following causes: driveshaft, u-joints, entire rear-end, tires/rims, tranny, flywheel, pinion angles.

My thought is: if the drive shaft should be centered through the crossmember, than the engine is sitting crooked- throwing off everything behind it. Which would also add another angle into the drive-train.

I am possibly stating the obvious, but I would like to get other's opinions.

Thank you for your help! I appreciate it.
Meant to say:

My thought is: if the drive shaft is not centered through the crossmember, than the engine is sitting crooked- throwing off everything behind it. Which would also add another angle into the drive-train.
npdunn is offline   Reply With Quote
Old 04-19-2014, 08:26 PM   #3
brad_man_72
the boat guy
 
brad_man_72's Avatar
 
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
Re: Drivetrain alignment and vibration

How did you rule out driveshaft? Only way to know is to have it ballanced Or if the vibration is still there when the driveshaft has been removed.
Then you would know your vibration was in the engine/trans, torque converters can cause a vibration.

Don't worry about the driveshaft being centered, I'm pretty sure the pinion isn't centered in the axle. Either way your truck doesn't care.
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck
66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate.
28, model a rpu project,

Last edited by brad_man_72; 04-19-2014 at 08:31 PM.
brad_man_72 is offline   Reply With Quote
Old 04-19-2014, 08:31 PM   #4
npdunn
Registered User
 
Join Date: Sep 2008
Location: queen creek, az
Posts: 4
Re: Drivetrain alignment and vibration

I have had the driveshaft checked 2x @ 2 different shops.
npdunn is offline   Reply With Quote
Old 04-20-2014, 09:06 AM   #5
fleetsidelarry
Senior Car Nut
 
fleetsidelarry's Avatar
 
Join Date: Jan 2008
Location: shellman bluff, GA
Posts: 1,411
Re: Drivetrain alignment and vibration

if it's a one-piece driveshaft it won't be centered for the reason brad_man mentioned. looking down, your engine/tranny and pinion centerlines will be parallel and slightly offset. same goes when looking from the side. yes, you are correct, this means a compound angle on the u-joints. designed that way
__________________
Larry
fleetsidelarry is offline   Reply With Quote
Old 04-20-2014, 09:49 AM   #6
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,702
Re: Drivetrain alignment and vibration

Here's a good read and some vibration troubleshooting info.
http://www2.dana.com/pdf/J3311-1-DSSP.pdf
geezer#99 is offline   Reply With Quote
Old 04-20-2014, 09:52 AM   #7
cdowns
Senior Member
 
cdowns's Avatar
 
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
Re: Drivetrain alignment and vibration

99.9% of drivetrains that have come out are not centered from the factory and they run just fine with no vibration
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane

MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF

DONT BELIEVE EVERYTHING YOU THINK

TAKE MY ADVISE;I DON'T USE IT ANYWAY
cdowns is offline   Reply With Quote
Old 04-20-2014, 06:55 PM   #8
brad_man_72
the boat guy
 
brad_man_72's Avatar
 
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
Re: Drivetrain alignment and vibration

No matter what direction the driveshaft is pointing there is only one angle at each end. No compound angle. Just an angle and a direction.
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck
66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate.
28, model a rpu project,
brad_man_72 is offline   Reply With Quote
Old 04-20-2014, 07:50 PM   #9
jjzepplin
Registered User
 
jjzepplin's Avatar
 
Join Date: Feb 2012
Location: Ruskin Florida
Posts: 4,566
Re: Drivetrain alignment and vibration

subbed to see where this goes
__________________
70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller
72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build
Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350
jjzepplin is offline   Reply With Quote
Old 04-20-2014, 08:39 PM   #10
fleetsidelarry
Senior Car Nut
 
fleetsidelarry's Avatar
 
Join Date: Jan 2008
Location: shellman bluff, GA
Posts: 1,411
Re: Drivetrain alignment and vibration

Quote:
Originally Posted by brad_man_72 View Post
No matter what direction the driveshaft is pointing there is only one angle at each end. No compound angle. Just an angle and a direction.
when there are angles in both the horizontal and vertical planes, Spicer calls it a compound angle. see page 9 and 10 of Geezer's link.
__________________
Larry
fleetsidelarry is offline   Reply With Quote
Old 04-20-2014, 09:58 PM   #11
Gumby
Registered User
 
Gumby's Avatar
 
Join Date: Dec 2008
Location: NW-Ohio
Posts: 2,525
Re: Drivetrain alignment and vibration

none are centered,

#1 due to steering shaft room

#2 it makes the drive line last longer, everything is off a little in severla direction down the line to make the drive shaft u joint last a long long time, if al lwas 100% centered and level, the bearings would sit in one spot and wear out, instead of rolling around inside.

#3 the need for #2, makes making room for #1 easier and made GMs life easier.
__________________
Chevy GMC Trucks Find Of The Day

https://www.facebook.com/ChevyGmcTrucksFindOfTheDay or http://ChevyGMCTrucks.com
Gumby is offline   Reply With Quote
Old 04-20-2014, 11:17 PM   #12
npdunn
Registered User
 
Join Date: Sep 2008
Location: queen creek, az
Posts: 4
Re: Drivetrain alignment and vibration

Thanks for everyone's input, back to the drawing board.
npdunn is offline   Reply With Quote
Reply

Bookmarks

Tags
driveshaft, drivetrain, engine & tranny alignment, vibration


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:27 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com