The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-01-2014, 09:05 PM   #1
86c20
Registered User
 
86c20's Avatar
 
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
air injection manifold plugs

ok so my 350 has the air injection set up and broke one of the tubes that goes to the manifold so i have a leak got the nut out of both sides tonight was just wondering if anyone knew the thread or where to get plugs so i can pass a cop with out being to loud lol, thanks mike
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph
1985 k30 "the ice cream truck from hell" no rust az truck
197-8??? c30 "ramp truck" 454
1978 monte carlo 350 350th with 2.73 gears. no rust. sc car
86c20 is offline   Reply With Quote
Old 09-01-2014, 09:15 PM   #2
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: air injection manifold plugs

I've had luck with Cummins engine oil drain plugs working.
Corts60 is offline   Reply With Quote
Old 09-01-2014, 09:39 PM   #3
Just call me Sean
Registered User
 
Just call me Sean's Avatar
 
Join Date: Jun 2014
Location: Orlando Florida
Posts: 1,598
Re: air injection manifold plugs

I only did it on my Ford, but it should be the same. The threads should be NPT (national pipe thread) so take the piece you removed to Lowes or Home Depot to match it up. Some auto parts stores might have NPT plugs too.
__________________
Quote:
Originally Posted by Early Cuyler
Fights begin, fingerprints are took, days is lost, bail is made, court dates are ignored, cycle is repeated.
Just call me Sean is offline   Reply With Quote
Old 09-02-2014, 02:34 AM   #4
frank69
Registered User
 
Join Date: Feb 2007
Location: Laughlin,Nv
Posts: 141
Re: air injection manifold plugs

I use 1/4 in. npt plugs.
frank69 is offline   Reply With Quote
Old 09-02-2014, 12:50 PM   #5
86c20
Registered User
 
86c20's Avatar
 
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
Re: air injection manifold plugs

it dont seem to be npt seem metric??? its a crate motor form mexico if that helps any and this is 3/4 od like a half inch pipe
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph
1985 k30 "the ice cream truck from hell" no rust az truck
197-8??? c30 "ramp truck" 454
1978 monte carlo 350 350th with 2.73 gears. no rust. sc car
86c20 is offline   Reply With Quote
Old 09-02-2014, 02:56 PM   #6
oily
Registered User
 
Join Date: Oct 2010
Location: Vancouver BC
Posts: 57
Re: air injection manifold plugs

I measured mine a few years ago. They were 19mm with a very fine thread and straight [not tapered]. Also the threaded hole wasnt that deep, so tapping them to pipe thread would be iffy. I would try a drain plug [Corts60] first. You need a friendly parts guy to try out the many sizes.
P.S. At the bottom of the threaded hole, the size reduces down to about 5/16 or so. You could try tapping that to a pipe plug, but I dont think there is much material to work with.
oily is offline   Reply With Quote
Old 09-02-2014, 08:00 PM   #7
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: air injection manifold plugs

Quote:
Originally Posted by 86c20 View Post
it dont seem to be npt seem metric??? its a crate motor form mexico if that helps any and this is 3/4 od like a half inch pipe
19mm and yes the threads are straight. No idea what pitch i.e.: 1.5, 1.25, etc. This is what a cummins drain plug is.
Corts60 is offline   Reply With Quote
Old 03-27-2015, 07:04 PM   #8
69m22zl1
Registered User
 
Join Date: Dec 2014
Location: Sacramento
Posts: 4
Re: air injection manifold plugs

Quote:
Originally Posted by 86c20 View Post
ok so my 350 has the air injection set up and broke one of the tubes that goes to the manifold so i have a leak got the nut out of both sides tonight was just wondering if anyone knew the thread or where to get plugs so i can pass a cop with out being to loud lol, thanks mike
Did you ever find a plug that worked in the manifolds? If so where did if find them? part # ? or who has them for sale?
69m22zl1 is offline   Reply With Quote
Old 03-27-2015, 08:14 PM   #9
86c20
Registered User
 
86c20's Avatar
 
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
Re: air injection manifold plugs

well see its like this, i gave the old nut that goes around the tubing to my gf and she found a plumbing bushing that fits. it is the most odd ball thing ever. it is comp by pipe adt and it went right in. think it is 3/4 can take a pic if needed but its not pretty. but i dont care it works
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph
1985 k30 "the ice cream truck from hell" no rust az truck
197-8??? c30 "ramp truck" 454
1978 monte carlo 350 350th with 2.73 gears. no rust. sc car
86c20 is offline   Reply With Quote
Old 03-27-2015, 10:16 PM   #10
69m22zl1
Registered User
 
Join Date: Dec 2014
Location: Sacramento
Posts: 4
Re: air injection manifold plugs

Quote:
Originally Posted by 86c20 View Post
well see its like this, i gave the old nut that goes around the tubing to my gf and she found a plumbing bushing that fits. it is the most odd ball thing ever. it is comp by pipe adt and it went right in. think it is 3/4 can take a pic if needed but its not pretty. but i dont care it works
Thanks for the quick reply, I'll check that out! Thank you!
69m22zl1 is offline   Reply With Quote
Old 03-27-2015, 10:36 PM   #11
Titomars
Registered User
 
Titomars's Avatar
 
Join Date: Feb 2015
Location: Santa Rosa, Ca.
Posts: 539
Re: air injection manifold plugs

Most GM AIR injection tubes are fitted to the manifolds with flare nuts which are straight threads not NPT. I always use Allen head set screws. The size I have used is 1/2 X 20 the taper of the set screw tip is close enough to the 45deg flare which lets the set screw seal at the flare not the threads. I also use anti-seize on the threads for removal at a later time.
Attached Images
 
__________________
1977 Chevrolet C/10 Silverado. Step-Side, Factory 454, TH400, 3.73 Posi 12 Bolt.
1975 Chevrolet El Camino. 350, TH400, 3.08 Posi 10 Bolt.
Titomars is offline   Reply With Quote
Old 03-27-2015, 11:44 PM   #12
Pampas56
Registered User
 
Join Date: Jul 2012
Location: Concrete, wa
Posts: 59
Re: air injection manifold plugs

When I had to replace the air injection tubes on my 350, we drilled the old flare nuts out and cleaned the threads up with a pipe tap. We discovered that they were a standard 1/4 inch NPS thread and dug up a straight plug tap to do the job.

A 1/2 by 20 plug would work worse than a 1/2 by 13 plug as the normal pitch of a 1/4. inch pipe thread is 14 TPI
__________________
1989 Silverado K2500ECLB- 307K miles with 90 K TBI 350-Not a show truck, a work tool that I can drive!

1998 Dakota EC 250K miles- I guess I'm just a truck guy now!
Pampas56 is offline   Reply With Quote
Old 03-28-2015, 12:08 AM   #13
Titomars
Registered User
 
Titomars's Avatar
 
Join Date: Feb 2015
Location: Santa Rosa, Ca.
Posts: 539
Re: air injection manifold plugs

Quote:
Originally Posted by Pampas56 View Post
When I had to replace the air injection tubes on my 350, we drilled the old flare nuts out and cleaned the threads up with a pipe tap. We discovered that they were a standard 1/4 inch NPS thread and dug up a straight plug tap to do the job.

A 1/2 by 20 plug would work worse than a 1/2 by 13 plug as the normal pitch of a 1/4. inch pipe thread is 14 TPI
Ahhh but 5/16 inverted flare nut threads are 1/2 X 20. Anyway that's what I do on my pre 81 vehicles. Now I can't really speak for newer engines. They might be metric for all I know.
__________________
1977 Chevrolet C/10 Silverado. Step-Side, Factory 454, TH400, 3.73 Posi 12 Bolt.
1975 Chevrolet El Camino. 350, TH400, 3.08 Posi 10 Bolt.
Titomars is offline   Reply With Quote
Old 03-28-2015, 07:31 AM   #14
86c20
Registered User
 
86c20's Avatar
 
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
Re: air injection manifold plugs

here is one thing i want to ask on this. are you guys using the 1/2 on the single line air or is it on the ones with 3 or 4 lines to the manifold?? mine is single
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph
1985 k30 "the ice cream truck from hell" no rust az truck
197-8??? c30 "ramp truck" 454
1978 monte carlo 350 350th with 2.73 gears. no rust. sc car
86c20 is offline   Reply With Quote
Old 03-28-2015, 11:29 AM   #15
Titomars
Registered User
 
Titomars's Avatar
 
Join Date: Feb 2015
Location: Santa Rosa, Ca.
Posts: 539
Re: air injection manifold plugs

Quote:
Originally Posted by 86c20 View Post
here is one thing i want to ask on this. are you guys using the 1/2 on the single line air or is it on the ones with 3 or 4 lines to the manifold?? mine is single
Sorry I was talking about the standard four tube AIR rail to exhaust manifold.
__________________
1977 Chevrolet C/10 Silverado. Step-Side, Factory 454, TH400, 3.73 Posi 12 Bolt.
1975 Chevrolet El Camino. 350, TH400, 3.08 Posi 10 Bolt.
Titomars is offline   Reply With Quote
Old 03-28-2015, 01:02 PM   #16
69m22zl1
Registered User
 
Join Date: Dec 2014
Location: Sacramento
Posts: 4
Re: air injection manifold plugs

Quote:
Originally Posted by Titomars View Post
Most GM AIR injection tubes are fitted to the manifolds with flare nuts which are straight threads not NPT. I always use Allen head set screws. The size I have used is 1/2 X 20 the taper of the set screw tip is close enough to the 45deg flare which lets the set screw seal at the flare not the threads. I also use anti-seize on the threads for removal at a later time.
I cut the air injection tubes and used a 22 mm to remove the them.
It looks like fine thread . An earlier post, Someone posted they used 19mm oil drain plug from Cummins diesel . Does anyone know year make model plug is from? Or if any of you can point out the plug I need would be very helpful . Thank you!
Attached Images
  
69m22zl1 is offline   Reply With Quote
Old 03-28-2015, 01:10 PM   #17
69m22zl1
Registered User
 
Join Date: Dec 2014
Location: Sacramento
Posts: 4
Re: air injection manifold plugs

Quote:
Originally Posted by Corts60 View Post
I've had luck with Cummins engine oil drain plugs working.
What year , make , model did you get the Cummins engine oil drain plug from?
69m22zl1 is offline   Reply With Quote
Old 07-13-2021, 12:40 PM   #18
Hart_Rod
*************
 
Hart_Rod's Avatar
 
Join Date: Apr 2005
Location: Pensacola, FL
Posts: 17,822
Re: air injection manifold plugs

Quote:
Originally Posted by 69m22zl1 View Post
What year , make , model did you get the Cummins engine oil drain plug from?
Bump. Anyone have an answer to this?
Hart_Rod is offline   Reply With Quote
Old 07-14-2021, 07:39 PM   #19
Corts60
Just here to tinker
 
Corts60's Avatar
 
Join Date: Jun 2008
Location: Holland, MI
Posts: 3,672
Re: air injection manifold plugs

Been a long time since I worked on this stuff, but try buying one of these and see if it works.

M22x1.5
https://www.napaonline.com/en/p/NDP7...&gclsrc=aw.ds&
Corts60 is offline   Reply With Quote
Old 07-15-2021, 09:03 AM   #20
Hart_Rod
*************
 
Hart_Rod's Avatar
 
Join Date: Apr 2005
Location: Pensacola, FL
Posts: 17,822
Re: air injection manifold plugs

Quote:
Originally Posted by Corts60 View Post
Been a long time since I worked on this stuff, but try buying one of these and see if it works.

M22x1.5
https://www.napaonline.com/en/p/NDP7...&gclsrc=aw.ds&
Thanks! I grabbed 2 at the parts store and the fit perfect, . For future questions on this matter, the part number is Dorman 652886.
Hart_Rod is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:04 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com