The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-07-2016, 04:31 PM   #1
gabej
Registered User
 
Join Date: Jul 2015
Location: Seattle
Posts: 11
1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Hi
Regarding a 1972 GMC C1500 (Sierra Grande) Non-Tilt Column.

I'm getting 1/4" to 1/2" play in my steering wheel/shaft in an up down/side to side range. I'm also getting about 1/2" play in and out. It seems as if it is because the tapered bottom end my turn signal canceling cam isn't engaging with the upper steering column bearing. Reading posts in the forum the tapered end of the cam should take up the gap and shore everything up but in my case it's not. My hub when pressed into the shaft doesn't descend down the shaft far enough to take up the gap between the Hub and the cam therefore pushing it up-to the bearing. Is there an adjustment I'm missing?

Thanks for your help.
gabej is offline   Reply With Quote
Old 03-07-2016, 09:55 PM   #2
swamp rat
Registered User
 
swamp rat's Avatar
 
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Downloading the shop manual may help, section 9 i think??

http://67-72chevytrucks.com/vboard/s...d.php?t=558016

I think the upper bearing is available, not sure about the bottom, i recall someone here subbed a bicycle bearing here somewhere.
__________________
Mike.

Swamp Rat build thread :
http://67-72chevytrucks.com/vboard/s...d.php?t=595019

72 3/4T 4X4
4" BDS Lift
33" BFG's
swamp rat is offline   Reply With Quote
Old 03-08-2016, 01:16 PM   #3
gabej
Registered User
 
Join Date: Jul 2015
Location: Seattle
Posts: 11
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Thanks. I've got the bearing installed. Are you saying uses bike bearings to take up that gap? I'm using the same components as the exploded view but there's still a gap between my cam and bearing causing the slop. Figuring there was some other adjustment in the bowl or the shaft that could be accomplished. Truck steers but that slop makes me nervous.
gabej is offline   Reply With Quote
Old 03-08-2016, 02:09 PM   #4
john
member #16
 
john's Avatar
 
Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Do you have the spring and washer on the lower shaft?
Attached Images
 
john is offline   Reply With Quote
Old 03-08-2016, 03:14 PM   #5
gabej
Registered User
 
Join Date: Jul 2015
Location: Seattle
Posts: 11
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Yes. Looks like there is some play there that I need to adjust. Also I found out that I missing two pieces in the column. The Service Manual calls them "The Shift Housing Bushing" and "Bushings Seat". (Parts #2 and #3 in the attached photos). No one seems to carry these. Might you have any idea where I could find them?
Attached Images
   
gabej is offline   Reply With Quote
Old 03-08-2016, 03:26 PM   #6
gabej
Registered User
 
Join Date: Jul 2015
Location: Seattle
Posts: 11
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Quote:
Originally Posted by john View Post
Do you have the spring and washer on the lower shaft?

Do you have a method you recommend for removing the play in the lower bearing set up? Seems that when I pull the steering wheel back and forth I get about 1/2" to 3/4" play above the spring and washer where it connects to the column housing. I found this Youtube video of someone elses issue that shows the area where the play is. Mine isn't this bad but it's bad enough.

https://www.youtube.com/watch?v=L3c-...ature=youtu.be
gabej is offline   Reply With Quote
Old 03-08-2016, 03:52 PM   #7
john
member #16
 
john's Avatar
 
Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
Re: 1972 GMC Steering Shaft Slop. Cam/Bearing Gap

Sorry I cant help on the missing parts, suggest you find a used column on the parts board for needed parts. I don't know if those parts will effect end play, I would think something else is assembled wrong.
john is offline   Reply With Quote
Reply

Bookmarks

Tags
1972 gmc, steering column, steering shaft


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:48 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com