The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-03-2022, 10:20 AM   #1
Nima
Blue 67
 
Join Date: Apr 2004
Location: Western WA
Posts: 1,159
Wiper motor and arms

Hello:

Besides the wiper arms, are these 3 the only parts or am I missing a smaller arm? I am trying to convert to a newport engineering 12 volt motor and It has been a while since I have taken these pieces apart.
Thannks
Attached Images
 
__________________
1953 GMC 3/4 ton: current project
1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake
1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!!
1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive
1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project
2005 Silverado 2500, 4x4 Duramax, original owner
Nima is offline   Reply With Quote
Old 10-03-2022, 01:37 PM   #2
leegreen
Registered User
 
Join Date: Mar 2022
Location: Surrey BC
Posts: 184
Re: Wiper motor and arms

#3 is the passenger side linkage, you are missing the drivers side.

https://www.classicindustries.com/sh...-1535062464283

#2 is the oem vacuum wiper motor. Hard to see but I think you are missing the spring that keeps the linkage on
https://www.classicindustries.com/sh...w-811580860707

There is a knob on the dash with short linage to control motor

#1 looks like a single speed electric wiper motor from a rear wiper, boat or something
leegreen is online now   Reply With Quote
Old 10-03-2022, 03:41 PM   #3
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 14,318
Re: Wiper motor and arms

#1 is as Leegreen said a single speed electric wiper motor. Very commonly used on older flat fender jeeps and they were used on hot rods in the 70's quite a bit. My experiene says they don't work well on AD trucks although there were guys advocating using them in the 70's.

https://www.summitracing.com/parts/u...0aAlR8EALw_wcB

https://www.ebay.com/itm/13379772843...4aAnGwEALw_wcB

I've got one of those motors in a box somewhere if I didn't sell it at a swap meet.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 10-03-2022, 08:38 PM   #4
Nima
Blue 67
 
Join Date: Apr 2004
Location: Western WA
Posts: 1,159
Re: Wiper motor and arms

Thank you guys.
Well, all these came out from udner the dash of my 53 GMC. I had them in a palstic bag during dissamebly but due to the lenght of the longer arm the plastic bag was not sealed well. So, I am assuming at one point the previous owner, decades ago, just installed the single stage motor on the drive side since I can't find the smaller arm. That is a bad news for me since the repalcement arms are spendy!
__________________
1953 GMC 3/4 ton: current project
1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake
1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!!
1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive
1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project
2005 Silverado 2500, 4x4 Duramax, original owner
Nima is offline   Reply With Quote
Old 10-04-2022, 01:00 AM   #5
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 14,318
Re: Wiper motor and arms

I've got an extra or two.

I've got a pair sitting somewhere that I pulled for some guy on FB who never got back to me if I can figure out where I put them or I can pull the left one off the orange cab easy enough. I'm not going to use that cowl at all if my plans hold true as I bought the truck to get the back half of the cab.

The big cost will be postage. Let me find the other one or get the one off the orange cab in the morning and find a box and weight it.
Attached Images
 
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 10-04-2022, 09:46 AM   #6
Nima
Blue 67
 
Join Date: Apr 2004
Location: Western WA
Posts: 1,159
Re: Wiper motor and arms

Quote:
Originally Posted by mr48chev View Post
I've got an extra or two.

I've got a pair sitting somewhere that I pulled for some guy on FB who never got back to me if I can figure out where I put them or I can pull the left one off the orange cab easy enough. I'm not going to use that cowl at all if my plans hold true as I bought the truck to get the back half of the cab.

The big cost will be postage. Let me find the other one or get the one off the orange cab in the morning and find a box and weight it.
Thank you.
__________________
1953 GMC 3/4 ton: current project
1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake
1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!!
1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive
1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project
2005 Silverado 2500, 4x4 Duramax, original owner
Nima is offline   Reply With Quote
Old 10-04-2022, 10:25 PM   #7
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 14,318
Re: Wiper motor and arms

It ended up being haul my wife around day and I didn't get out to pull the arm off until later.

it looks like someone stripped the nut on that one along breaking the bezel.

My helper wasn't very impressed either so we will have to dig the other one out now.

At least we got a good sunset shot out of the deal and now I have to figure out what I did with the other one.

My wife's haircut came out good and lunch was good though.
Attached Images
   
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 10-05-2022, 09:43 AM   #8
Nima
Blue 67
 
Join Date: Apr 2004
Location: Western WA
Posts: 1,159
Re: Wiper motor and arms

Quote:
Originally Posted by mr48chev View Post
It ended up being haul my wife around day and I didn't get out to pull the arm off until later.

it looks like someone stripped the nut on that one along breaking the bezel.

My helper wasn't very impressed either so we will have to dig the other one out now.

At least we got a good sunset shot out of the deal and now I have to figure out what I did with the other one.

My wife's haircut came out good and lunch was good though.
The kitty and the sunset are beautiful, the wiper arm with stripped tip is another story!
__________________
1953 GMC 3/4 ton: current project
1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake
1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!!
1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive
1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project
2005 Silverado 2500, 4x4 Duramax, original owner
Nima is offline   Reply With Quote
Old 10-05-2022, 04:46 PM   #9
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 14,318
Re: Wiper motor and arms

I only bought that truck for the roof and the back panel of the cab.

The roof and back side of the cab are near perfect but the rest of the truck had had a hard life. It had about 500 lbs of brackets welded to the frame for pumps and a water
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 10-07-2022, 01:57 AM   #10
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 14,318
Re: Wiper motor and arms

I finally found where I had stuck it.

20,00 shipped is what I need.

PM me for the details.

The bezel is a patina bezel that may or may not polish up and the nut has some marks on it
Attached Images
  
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:35 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com