|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-23-2015, 09:34 PM
|
#1 |
|
Registered User
Join Date: Apr 2007
Location: pasadena,TEXAS
Posts: 880
|
What size are deez nuts
I need to take the nuts on the ubolts on the rear end off to install an ece super track bar. I tried a 1" & a 1 1/8 and neither fit so I need to go shopping tomorrow, I assume it will be a 1 1/16 but would like to know for sure. Anyone know right off the top of their head?
__________________
1971 Cheyenne SWB 402BB, 700R4, 3.73 posi, PS, PB, A/C, Tilt, Tach "Wanda" Don't argue with idiots, People watching may not be able to tell the difference... There's someone in my head........But it's not me...... cheap tricks thread great info here!! http://67-72chevytrucks.com/vboard/s...d.php?t=489394 |
|
|
|
02-23-2015, 10:35 PM
|
#2 |
|
Registered User
 
Join Date: May 2014
Location: PA
Posts: 1,417
|
Re: What size are deez nuts
Tape measure or dial caliper....busting doze nutz LMAO
__________________
1967 C10, LWB, 250, Powerglide, PS, PB, 3/4 STATIC DROP |
|
|
|
|
02-23-2015, 11:03 PM
|
#3 |
|
Registered User
Join Date: Feb 2015
Location: Kirtland NM
Posts: 29
|
Re: What size are deez nuts
Well if 1 inch is too small and 1-1/8 is too large then 1-1/16 will be the fit. did mine a long time ago can't remember off the top of my head
__________________
what about that little guy? That little guy??!! I wouldn't worry about that little guy |
|
|
|
|
02-23-2015, 11:12 PM
|
#4 |
|
Registered User
Join Date: Dec 2012
Location: Tacoma WA
Posts: 274
|
Re: What size are deez nuts
18" crescent wrench and a cheater bar to
 take them off and then a 3/4" torque wrench that will go to 150 foot pounds to torque them back up.
__________________
1970 3/4 ton long box GMC !968 C10 short stepside (Papa's Old Lorry) 2006 2500 HD Silverado Duramax/Alison |
|
|
|
|
02-23-2015, 11:18 PM
|
#5 |
|
Registered User
Join Date: Feb 2015
Location: Kirtland NM
Posts: 29
|
Re: What size are deez nuts
3/4 torque wrench to 150!!!! 1/2 at 235 is more like it. 3/4 should be 250 to 600
__________________
what about that little guy? That little guy??!! I wouldn't worry about that little guy |
|
|
|
|
02-24-2015, 07:39 AM
|
#6 |
|
Registered User
Join Date: Dec 2013
Location: Omaha NE
Posts: 620
|
Re: What size are deez nuts
I have a broken 1 1/16" x 1/2" drive Socket you can have! I had to use a 3/4" drive and a long cheater. Them things are tough!
|
|
|
|
|
02-24-2015, 12:47 PM
|
#7 |
|
Registered User
Join Date: May 2012
Location: Faith,NC
Posts: 1,623
|
Re: What size are deez nuts
1 1/16" is correct. I know because I had to go buy the socket.
|
|
|
|
|
02-24-2015, 12:59 PM
|
#8 |
|
Senior Member
Join Date: Sep 2007
Location: Albuquerque NM
Posts: 7,814
|
Re: What size are deez nuts
1 1/16
__________________
1967custom |
|
|
|
|
02-24-2015, 07:04 PM
|
#9 |
|
Registered User
Join Date: Apr 2007
Location: pasadena,TEXAS
Posts: 880
|
Re: What size are deez nuts
yep that is correct, went and bought a impact socket today. will start the job after I get home from the dentist tomorrow morning. hope that I am not getting into something over my head. after the install I will have to go get my exhaust modified cause the new track bar appears that is is going to hit it...
__________________
1971 Cheyenne SWB 402BB, 700R4, 3.73 posi, PS, PB, A/C, Tilt, Tach "Wanda" Don't argue with idiots, People watching may not be able to tell the difference... There's someone in my head........But it's not me...... cheap tricks thread great info here!! http://67-72chevytrucks.com/vboard/s...d.php?t=489394 |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
