Pictures of Lowered Burbs (3/5 vs 4/6) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

D-n-Tyke · 05-26-2022, 02:17 PM

Getting ready to place the order for my suspension however I am not sure if I want to go 3/5 or 4/6. Going to be a static drop and want to be able to drive without to many issue but love the low look. Already have wheels bought, 20X10 in rear 20x8 up front.

Can you guys post up some pictures of these different set ups (3/5 vs 4/6). I tried searching but didn't find much, if there is already a thread covering this if you could point me to that that would be great too. Thanks.

**HO455** · 05-29-2022, 06:32 PM

Did you see this thread?

http://67-72chevytrucks.com/vboard/s...ad.php?t=68579

**hevy_chevy67** · 06-01-2022, 01:57 PM

In a week or two I should be able to get some good pics of my Burb on a 3.5/5 with 20" wheels. Is your frame notched? 6" might be cutting it close, just based on where my Burb is sitting at 5".

**hevy_chevy67** · 06-12-2022, 10:52 AM

3.5/5
245 45 20 / 275 40 20

D-n-Tyke · 06-18-2022, 06:13 PM

Thanks for the picture. I just placed my order yesterday. Starting out ar 3.5" up front (2.5 modual drop spindles and 1" lowering spring) and 4" drop springs in the back. We'll install all that and see how it looks and go from there. If it isn't low enough I also ordered up a 1" block so if I want to go lower I can cut 1/2 a coil up front and put that block in. Going to be a bit before I can get it all installed but will post up some pictures.

As for notching, I did order up a HD notch kit and will install that at the same time.

05-26-2022, 02:17 PM	#1
D-n-Tyke Registered User Join Date: Aug 2016 Location: El Cajon, CA Posts: 247	Pictures of Lowered Burbs (3/5 vs 4/6) Getting ready to place the order for my suspension however I am not sure if I want to go 3/5 or 4/6. Going to be a static drop and want to be able to drive without to many issue but love the low look. Already have wheels bought, 20X10 in rear 20x8 up front. Can you guys post up some pictures of these different set ups (3/5 vs 4/6). I tried searching but didn't find much, if there is already a thread covering this if you could point me to that that would be great too. Thanks.

05-29-2022, 06:32 PM	#2
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 10,786	Re: Pictures of Lowered Burbs (3/5 vs 4/6) Did you see this thread? http://67-72chevytrucks.com/vboard/s...ad.php?t=68579 __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

06-01-2022, 01:57 PM	#3
hevy_chevy67 Registered User Join Date: May 2005 Location: Blackfalds, Alberta Posts: 577	Re: Pictures of Lowered Burbs (3/5 vs 4/6) In a week or two I should be able to get some good pics of my Burb on a 3.5/5 with 20" wheels. Is your frame notched? 6" might be cutting it close, just based on where my Burb is sitting at 5". __________________ 1971 Chevrolet K10 - SWB, 5.3LS, 4L60e 1970 Chevrolet K5 Blazer - Project 1969 Chevrolet C10 - SWB, 350 Holley Sniper, 700r4 1969 GMC Suburban - 5.3 LS, 4L60e

06-12-2022, 10:52 AM	#4
hevy_chevy67 Registered User Join Date: May 2005 Location: Blackfalds, Alberta Posts: 577	Re: Pictures of Lowered Burbs (3/5 vs 4/6) 3.5/5 245 45 20 / 275 40 20 Attached Images __________________ 1971 Chevrolet K10 - SWB, 5.3LS, 4L60e 1970 Chevrolet K5 Blazer - Project 1969 Chevrolet C10 - SWB, 350 Holley Sniper, 700r4 1969 GMC Suburban - 5.3 LS, 4L60e

06-18-2022, 06:13 PM	#5
D-n-Tyke Registered User Join Date: Aug 2016 Location: El Cajon, CA Posts: 247	Re: Pictures of Lowered Burbs (3/5 vs 4/6) Thanks for the picture. I just placed my order yesterday. Starting out ar 3.5" up front (2.5 modual drop spindles and 1" lowering spring) and 4" drop springs in the back. We'll install all that and see how it looks and go from there. If it isn't low enough I also ordered up a 1" block so if I want to go lower I can cut 1/2 a coil up front and put that block in. Going to be a bit before I can get it all installed but will post up some pictures. As for notching, I did order up a HD notch kit and will install that at the same time.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.