Lets see your welding carts!!

[jmedero]

Thinking of building a new welding cart for the shop. I've got an old tool box and just wanted to see what's out there.
Posted via Mobile Device

[hugger6933]

I've got one to beat everyone! I took the old rotted out center section of a gas grille and removed all of the cooking area. Then I added a wide board there where the grille part went then I placed my welder plasma combo on it and held it in place with a ratch strap. I have had this stetup for over like 3 years and it is perfect for what I need it to do. It is ugly like me but does its job and waste nothing, I even use the box that the machine came in turned over up side down to cover the machine to keep it clean in the body shop as it gets pretty dusty as ya'll could imagine. Total cost in the welder cart ZERO!!! if I remember I will try to get some pics when I go to the shop next time. Jim

[jmedero]

Sweet
Posted via Mobile Device

[Mr.Hyde]

I'm actually looking to do about the same thing i just picked up a new lincoln 140c seen some nicer ones seen some ugly ones.. I'm slowly building up my one car workshop haha

[jmedero]

I hear you. Just finished up my shop and now just working to get it all set up. I've got a welding cart I got from HF. I just think it would be good to have some storage on the cart
Posted via Mobile Device

[Mr.Hyde]

ya its hard sometimes without a lot of room i dream of acreage with a giant workshop

[bruin_d]

There was a pretty badass one in HotRod or CarCraft magazine a few months back. I'll see if I can find it.

[jmedero]

Thanks d. I was looking at pics of your Burb today trying to get motivated to get on mine.
Posted via Mobile Device

[bruin_d]

Here's one...

[bruin_d]

This is the one I saw in the Hot Rod magazine...

[bruin_d]

Originally Posted by jmedero

Thanks d. I was looking at pics of your Burb today trying to get motivated to get on mine.
Posted via Mobile Device

HAHAHA!!! GET TO WORK!!! I'm missing mine. I haven't seen it since June. I have a new tranny waiting for me to install when I get back to SoCal.

[jmedero]

I would like to see some finished pics of the rear floor. Brainstorming on ideas.
Posted via Mobile Device

[jmedero]

These look good
Posted via Mobile Device

[LEEVON]

4'x2'x3/8" top, built in my garage last winter and it's invaluable. The vise is a 4" English made machinist's vise of 60's vintage. It was barely used when I picked it up from Craigslist. I'd like to add another platform on the opposite end for a plasma cutter when I get one.

[jmedero]

That's what I'm talking about. Work bench and welding station in one.
Posted via Mobile Device

[jmedero]

I was thinking of a wood top. Would metal be better?
Posted via Mobile Device

[oem4me]

Originally Posted by jmedero

I was thinking of a wood top. Would metal be better?
Posted via Mobile Device

Wood burns and metal doesn't, but the biggest reason would have to be that your smaller welding projects can be grounded through the benchtop, so there is no need to attach the ground clamp to the workpiece itself.

[_Ogre]

i should be embarrassed to post mine, it's an old upper kitchen cabinet on 2'' plastic casters
my lincoln weldpac 100 is flux core only

[dwcsr]

Originally Posted by _Ogre

i should be embarrassed to post mine, it's an old upper kitchen cabinet on 2'' plastic casters
my lincoln weldpac 100 is flux core only

My first welding cart/bench was a pair of plastic Stanley saw horses and a piece if 2'x3'x3/16" plate. Worked fine for several years till I made my 60" square table.

[Mr.Hyde]

What's wrong with a cabinet? Nice flat top and storage? I see an issue with sparks but you aren't welding on top of it. Also I agree a metal top is ideal that way anything on the table is grounded only issue with that again is it can arc to the table and stick possibly leaving small divots in the flat surface or an end. Unlikely but it happens its always ideal to ground directly on the part your welding. Been welding since I was 15
Posted via Mobile Device

[sleepertruck72]

Those are nice welding carts/tables ! Heres something I made and had my cousin cut me the awesome center piece It just sits in my garage so it seems I know how to weld

[midniteblues]

Originally Posted by hugger6933

I've got one to beat everyone! I took the old rotted out center section of a gas grille and removed all of the cooking area. Then I added a wide board there where the grille part went then I placed my welder plasma combo on it and held it in place with a ratch strap. I have had this stetup for over like 3 years and it is perfect for what I need it to do. It is ugly like me but does its job and waste nothing, I even use the box that the machine came in turned over up side down to cover the machine to keep it clean in the body shop as it gets pretty dusty as ya'll could imagine. Total cost in the welder cart ZERO!!! if I remember I will try to get some pics when I go to the shop next time. Jim

I used a gas grill frame too for years. it was rickety wobbly and just terrible.
but it was salvagable so one day I decided too fix it up and bolted a 1/4 thick top on it and made a shelf on the bottom put some hooks on the side for cords it was looking good with fresh dollar store paint job and all. I wheeled it outa the basement to push it out too the garage but got I got sidetracked(her) and left it outside the basement doors near the garbage cans of course when she got up the next day she pushed it too the curb with the trash cans later that day I got home and thought wth did i put the cart at then thinking about the day prior,I went out too get the cart and it was gone???? I never even got too use my fixed up spiffy grill framed welding cart. but I'm sure the trashman was happy too take it
I said too her "did it look like trash?".....she said "well no but YOU DID have it out at the cans on trash day".......

oh well

[_Ogre]

live and learn midniteblues, live and learn

[midniteblues]

Originally Posted by _Ogre

live and learn midniteblues, live and learn

slowly but surely

[72BlckButy]

Originally Posted by LEEVON

4'x2'x3/8" top, built in my garage last winter and it's invaluable. The vise is a 4" English made machinist's vise of 60's vintage. It was barely used when I picked it up from Craigslist. I'd like to add another platform on the opposite end for a plasma cutter when I get one.

I love the welding cart!

Is that a Hobart 140?