1970 C10 Hood Emblem Replacement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rmawyer · 11-01-2015, 08:10 PM

Got a replacement hood emblem from Brother's. What is the best way to replace? I don't want to damage paint job that came with this recent purchase. I see under hood where I can remove hood latch pin to get inside to old emblem, but can't quite reach it. Is there a tool or method to help with removal of old and replacement with new? Sorry if these questions seem elementary - this is my first attempt at trim work. Thanks.

leftybass209 · 11-01-2015, 08:19 PM

Use blue masking tape on everything if you are afraid of scratching the paint. Also use it on your ratchet, or slip a piece of hose over it. The nuts retaining the emblem are easily accessible after you remove the latch plate.

rmawyer · 11-01-2015, 08:34 PM

Thanks - you mentioned nuts that secure the emblem. In the replacement piece it looks like the two stud fasteners are friction fit - do they get installed using a ratchet? If not, what do you use to force the fastener onto the stud?

leftybass209 · 11-01-2015, 08:49 PM

I don't recall the name of the type of nuts. The are like capture nuts I think. They are hollow on the backside with a flared edge and a hole (obviously!!!) through the center, but it has a split on each side of the hole. It easily spins on and just stops the piece from moving around. They aren't meant for any serious psi clamping force.

**70STOVEBOLT** · 11-01-2015, 10:08 PM

Speed nuts I think they are called. They are a thin stamped steel nut like leftybass described.

Longhornss · 11-03-2015, 12:30 AM

Lefty is describing a "barrel nut" this is a misleading name because there is no threads in this style.
Google emblem barrel nut.

**FirstOwner69** · 11-03-2015, 02:16 AM

Here's a link to an eBay listing for the type of nuts originally used. My Trim Parts repro bowtie hood emblem had them included. These were also used with the fender emblems. I'm not sure if the size in the eBay listing is correct for either application.

http://www.ebay.com/itm/10-Washer-he...-/221698021796

OregonNed · 11-03-2015, 07:04 AM

I just bought a bag of these nuts from NAPA auto parts for my fender emblems - easy tp use and reasonably priced too..

rmawyer · 11-15-2015, 02:34 PM

Thanks for responding - I was able to remove the old and replace it with the new. FYI - the original nuts were threaded and had to be unscrewed. The new nuts were friction fit. I did have to remove the latch plate to get to the trim piece.

Gromit · 11-15-2015, 09:59 PM

Thanks for asking that question to the group RMawyer.. I have been wondering about that exact thing myself here for a while and I definitely could not figure it out myself no matter how many times I tried to shine a flashlight up through the hood to see how the damn thing (bowtie hood ornament) was fixed up in there...I could not see it...

11-01-2015, 08:10 PM	#1
rmawyer Registered User Join Date: Jul 2015 Location: Fishing Creek, MD Posts: 49	1970 C10 Hood Emblem Replacement Got a replacement hood emblem from Brother's. What is the best way to replace? I don't want to damage paint job that came with this recent purchase. I see under hood where I can remove hood latch pin to get inside to old emblem, but can't quite reach it. Is there a tool or method to help with removal of old and replacement with new? Sorry if these questions seem elementary - this is my first attempt at trim work. Thanks.

11-01-2015, 08:19 PM	#2
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,186	Re: 1970 C10 Hood Emblem Replacement Use blue masking tape on everything if you are afraid of scratching the paint. Also use it on your ratchet, or slip a piece of hose over it. The nuts retaining the emblem are easily accessible after you remove the latch plate.

11-01-2015, 08:34 PM	#3
rmawyer Registered User Join Date: Jul 2015 Location: Fishing Creek, MD Posts: 49	Re: 1970 C10 Hood Emblem Replacement Thanks - you mentioned nuts that secure the emblem. In the replacement piece it looks like the two stud fasteners are friction fit - do they get installed using a ratchet? If not, what do you use to force the fastener onto the stud?

11-01-2015, 08:49 PM	#4
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,186	Re: 1970 C10 Hood Emblem Replacement I don't recall the name of the type of nuts. The are like capture nuts I think. They are hollow on the backside with a flared edge and a hole (obviously!!!) through the center, but it has a split on each side of the hole. It easily spins on and just stops the piece from moving around. They aren't meant for any serious psi clamping force.

11-01-2015, 10:08 PM	#5
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,214	Re: 1970 C10 Hood Emblem Replacement Speed nuts I think they are called. They are a thin stamped steel nut like leftybass described. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

11-03-2015, 12:30 AM	#6
Longhornss Registered User Join Date: Mar 2015 Location: Windsor,Ontario Canada Posts: 255	Re: 1970 C10 Hood Emblem Replacement Lefty is describing a "barrel nut" this is a misleading name because there is no threads in this style. Google emblem barrel nut.

11-03-2015, 02:16 AM	#7
FirstOwner69 Senior Member Join Date: May 2010 Location: Wisconsin & Arizona Posts: 4,839	Re: 1970 C10 Hood Emblem Replacement Here's a link to an eBay listing for the type of nuts originally used. My Trim Parts repro bowtie hood emblem had them included. These were also used with the fender emblems. I'm not sure if the size in the eBay listing is correct for either application. http://www.ebay.com/itm/10-Washer-he...-/221698021796

11-03-2015, 07:04 AM	#8
OregonNed Registered User Join Date: Dec 2012 Location: Vancouver, Washington Posts: 1,644	Re: 1970 C10 Hood Emblem Replacement I just bought a bag of these nuts from NAPA auto parts for my fender emblems - easy tp use and reasonably priced too.. __________________ 1968 Chevrolet C/10 LWB - 327, TH350 - 4/5 Drop

11-15-2015, 02:34 PM	#9
rmawyer Registered User Join Date: Jul 2015 Location: Fishing Creek, MD Posts: 49	Re: 1970 C10 Hood Emblem Replacement Thanks for responding - I was able to remove the old and replace it with the new. FYI - the original nuts were threaded and had to be unscrewed. The new nuts were friction fit. I did have to remove the latch plate to get to the trim piece.

11-15-2015, 09:59 PM	#10
Gromit Registered User Join Date: Jul 2015 Location: Central Coast, CA Posts: 498	Re: 1970 C10 Hood Emblem Replacement Thanks for asking that question to the group RMawyer.. I have been wondering about that exact thing myself here for a while and I definitely could not figure it out myself no matter how many times I tried to shine a flashlight up through the hood to see how the damn thing (bowtie hood ornament) was fixed up in there...I could not see it...



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.