|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-06-2014, 02:32 PM
|
#1 |
|
Registered User
Join Date: Feb 2013
Location: Austin Texas
Posts: 17
|
Installing "Custom" cab moldings
So I bought these cab moldings for my 65 longbed but not quite sure how I want to go about putting them on just yet. Any ideas?? I know I've really only got about 2 choices, glue it or drill it on there. Just curious what you guys have done and what's worked and hasn't.
|
|
|
|
01-06-2014, 02:36 PM
|
#2 |
|
Senior Member
 
Join Date: Sep 2011
Location: Hanford, CA
Posts: 1,027
|
Re: Installing "Custom" cab moldings
You should drill pilot holes for the screws and then pick up a set of replacement screws from any of the classic truck supply shops (LMC, Classic Parts, Brothers). They all have the screws, they're stainless, and very inexpensive.
__________________
Poor and content is Rich...and Rich enough! - William Shakespeare 1966 C10 Custom Cab "Luigi" Big Window - SWB Fleetside 350 V-8 - Powerglide My not so much a build thread as a "Slow Progression Thread":http://67-72chevytrucks.com/vboard/s...d.php?t=486894 |
|
|
|
|
01-06-2014, 02:41 PM
|
#3 |
|
Registered User
Join Date: Sep 2013
Location: Cold Lake, AB
Posts: 402
|
Re: Installing "Custom" cab moldings
I used 3M double sided tape.
|
|
|
|
|
01-06-2014, 02:47 PM
|
#4 |
|
Registered User
Join Date: Feb 2013
Location: Austin Texas
Posts: 17
|
Re: Installing "Custom" cab moldings
Its somewhat of a tight fit where the molding meets the edge of the door. Would tape make it stick out too far? or would the heads of the screws stick out too far? Do you think this could be a different problem related to the position of the door?
|
|
|
|
|
01-06-2014, 02:59 PM
|
#5 |
|
Registered User
Join Date: Sep 2013
Location: Cold Lake, AB
Posts: 402
|
Re: Installing "Custom" cab moldings
I used the double sided tape on the leading edge and there's no impact with the door.
This solution worked for me as I didn't want to drill holes in my cab. |
|
|
|
|
01-06-2014, 03:19 PM
|
#6 |
|
Post Whore
Join Date: Mar 2013
Location: Southern Oregon
Posts: 10,384
|
Re: Installing "Custom" cab moldings
Easiest thing would be double side tape...but I would screw it on just for the fact of knowing that they won't fly or fall off.
__________________
1966 Chevy C10 "Project Two Tone" http://67-72chevytrucks.com/vboard/s...d.php?t=596643 1964 GMC "Crustine" semi-build:http://67-72chevytrucks.com/vboard/s...d.php?t=665056 My youtube channel. Username "Military Chevy": https://www.youtube.com/channel/UC_h...fzpcUXyK_5-uiw |
|
|
|
|
01-06-2014, 04:02 PM
|
#7 |
|
Registered User
Join Date: Nov 2011
Location: fayetteville nc
Posts: 10,338
|
Re: Installing "Custom" cab moldings
Id go with the factory option and get the 4 screws that they each take.
__________________
1963 Short bed step side SBW 427 big block and borg warner T-16 HD 3 speed manual http://67-72chevytrucks.com/vboard/s...d.php?t=519869 1963 Short bed fleetside BBW 348 1st gen big block w/Powerglide http://67-72chevytrucks.com/vboard/s...d.php?t=619024 1964 Short bed trailer |
|
|
|
|
01-06-2014, 08:55 PM
|
#8 | |
|
Registered User
Join Date: Sep 2012
Location: Oregon
Posts: 3,303
|
Re: Installing "Custom" cab moldings
Quote:
__________________
GOD BLESS AMERICA! |
|
|
|
|
|
01-07-2014, 02:54 PM
|
#9 |
|
Registered User
Join Date: Feb 2013
Location: Austin Texas
Posts: 17
|
Re: Installing "Custom" cab moldings
Does anyone have a link to a site that sells the hardware? I just checked classic parts an they don't sell just the screws.
|
|
|
|
|
| Bookmarks |
| Tags |
| 1965 c10, advice, cab trim, custom, molding |
|
|
Linear Mode
