The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > Diesel Conversions

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-03-2021, 02:01 AM   #1
jarrodblake
Registered User
 
jarrodblake's Avatar
 
Join Date: Sep 2017
Location: Patriot IN
Posts: 163
engine speed sensor/ crank sensor wiring for tachometer 97-98 sensor

I installed a 97-98 engine speed sensor/ crank sensor to run my tachometer. I have already ran a 5 volt power, ground and sender wire for it but I can't find the pin out.

here is a pic of the plugs the one with the 123 is the harness side the the other in the sensor.



I need to know where the power, ground and sender wires go on the 123 plug.


Here is a pic of the sender I am using.

jarrodblake is offline   Reply With Quote
Old 09-16-2021, 05:49 AM   #2
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,112
Re: engine speed sensor/ crank sensor wiring for tachometer 97-98 sensor

I just went through this a couple years ago when I did a 6.4 12v swap. I'll see if I can find the info again.

On edit, I found it. It was in the instructions for the swap helper tach box I used. Sorry the image is side ways.

1 is 5 volt supply
2 is Sensor ground
3 is Crankshaft position sensor signal
Attached Images
File Type: pdf EPSpinout.pdf (45.8 KB, 116 views)
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.

Last edited by Dieselwrencher; 09-16-2021 at 06:13 AM.
Dieselwrencher is offline   Reply With Quote
Old 09-16-2021, 11:08 PM   #3
jarrodblake
Registered User
 
jarrodblake's Avatar
 
Join Date: Sep 2017
Location: Patriot IN
Posts: 163
Re: engine speed sensor/ crank sensor wiring for tachometer 97-98 sensor

Quote:
Originally Posted by Dieselwrencher View Post
I just went through this a couple years ago when I did a 6.4 12v swap. I'll see if I can find the info again.

On edit, I found it. It was in the instructions for the swap helper tach box I used. Sorry the image is side ways.

1 is 5 volt supply
2 is Sensor ground
3 is Crankshaft position sensor signal

Thank you!
jarrodblake is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:53 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com