The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-25-2010, 10:19 AM   #1
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
distributer?

i have a ? every couple of weeks my distributer comes loose and it can be turned i tighten the hold down but it seems to come loose again i dont know why this is happining any help thanx
81ratrodc10 is offline   Reply With Quote
Old 05-25-2010, 11:56 AM   #2
jchav62
1962 C-10
 
jchav62's Avatar
 
Join Date: Apr 2005
Location: Las Vegas, New Mexico
Posts: 4,978
Re: distributer?

Strange. Maybe try using a little lock tite or something to keep it from backing out.
__________________
Joseph Chavez
"See the USA in a Chevrolet!!"
......................_____
.........________//__{\_____
,,,,,,,/__(O)___//___/__(O)_/

1962 C10 Shortbed Fleetside 327/th350 GV overdrive
1974 C10 Longbed Fleetside 350/th350 "The Trash Truck"
1999 Chevy 2500 OBS, Longbed 5.7/4L80E 4x4
2015 GMC Sierra SLE 1500 4x4
jchav62 is offline   Reply With Quote
Old 05-25-2010, 01:00 PM   #3
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

ya it is wierd the po told me it would run great then like crap couldnt figure it out i got home did a tune up on it and found out it was lose so i tightened it and it is still doing it ill have to try that
81ratrodc10 is offline   Reply With Quote
Old 05-25-2010, 01:33 PM   #4
78 Chevyrado
Account Suspended
 
Join Date: Dec 2007
Location: Unnapreciative, Trollville
Posts: 2,079
Re: distributer?

If the bolt isn't stripped, it may be half stripped... just enough to make the threads loose, but not enough to actually pull out. when you screw the bolt in without the bracket, can you pull it in and out at all?
78 Chevyrado is offline   Reply With Quote
Old 05-25-2010, 03:42 PM   #5
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

i have never taken it out completly should i
81ratrodc10 is offline   Reply With Quote
Old 05-25-2010, 03:44 PM   #6
boatpuller
Registered User
 
boatpuller's Avatar
 
Join Date: Sep 2005
Location: Sun City West, Az
Posts: 3,822
Re: distributer?

yeah try that..or else run a thread cleaner down there the same size and try a new bolt.and some loctite.
__________________
" Never look up a dead dogs butt."
boatpuller is offline   Reply With Quote
Old 05-25-2010, 04:26 PM   #7
Chevytrux4me
Certified Gearhead
 
Chevytrux4me's Avatar
 
Join Date: Feb 2007
Location: Athens, West Virginia
Posts: 186
Re: distributer?

Is it possible that the hold-down may not be right-side-up? What about using a nylon locknut to secure it better and counteract vibration?
__________________
"I drive my pickup into the big city, 'n write my room number right on the bottom o' my boot. Jus' so I don't forget where I live. That's right, y'all. That's how I roll!"
Chevytrux4me is offline   Reply With Quote
Old 05-25-2010, 04:42 PM   #8
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

how do i know if the hold down is wrong side
81ratrodc10 is offline   Reply With Quote
Old 05-25-2010, 06:33 PM   #9
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

do i have to take the dist out to get the bolt all the way out
81ratrodc10 is offline   Reply With Quote
Old 05-25-2010, 10:20 PM   #10
Chevytrux4me
Certified Gearhead
 
Chevytrux4me's Avatar
 
Join Date: Feb 2007
Location: Athens, West Virginia
Posts: 186
Re: distributer?

I don't think you should have to remove the distributor to get the bolt all the way out. Some of the hold-downs I've seen have a slight curve to them, and should be installed with the two 'fingers' pointing downward.. However, some of the newer ones made out of billet alum and so forth I've seen are pretty much flat. I've wondered if the flat ones work as well as the curved. I was just thinking if the 'fingers' are pointing up and not downward, or if the hold-down is curved or flat. this might let the distributor bolt or nut loosen. I hadn't thought of it earlier, but I've seen hold-down bolts, and I've also seen a stud and nut setup. That's what I meant about the nylon locknut. Obviously, a bolt would need to be replaced with a stud to do that. Not knowing what's on your truck, you might want to look at the type of hold-down you have. Also, is there by chance a washer under it, as opposed to on top? Another thing to consider, this would require pulling the dist up, but I wonder if there's a gasket under the dist base, or is it possibly missing? I can see where this would let the dist base turn also. ...I'm by no means a master mechanic, just considering different possibilities of what might cause this.. Having worked on some trucks, tractors, and more than my share of old sports cars, I've seen lots of interesting 'stuff' over the years. I'm interested to know the outcome of this one.
__________________
"I drive my pickup into the big city, 'n write my room number right on the bottom o' my boot. Jus' so I don't forget where I live. That's right, y'all. That's how I roll!"
Chevytrux4me is offline   Reply With Quote
Old 05-25-2010, 10:25 PM   #11
longbedrick
Registered User
 
longbedrick's Avatar
 
Join Date: Nov 2009
Location: Gilroy,CA
Posts: 193
Re: distributer?

loctite on your bolt and make sure you tighten your crows foot down real snug. get a crows foot tool if you can't get in there. I invested in them a couple years ago. good investment in tight places. if your intake is aluminum, be cautious not to strip your threads
longbedrick is offline   Reply With Quote
Old 05-25-2010, 10:51 PM   #12
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

i have a performer rpm intake dont know if its aluminum and ill have to check and c how the crows foot os on there
81ratrodc10 is offline   Reply With Quote
Old 06-03-2010, 10:52 PM   #13
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

okay so finaly got around to checking it out today the bolt is still tight but the dist still moves when i tightened it the first time the dist was tight not sure what it is
81ratrodc10 is offline   Reply With Quote
Old 06-03-2010, 11:06 PM   #14
Camaro_nut2001
Chevy Lover Till The End.
 
Camaro_nut2001's Avatar
 
Join Date: Dec 2009
Location: Mascot TN.
Posts: 795
Re: distributer?

Take the bolt out & flip your hold down piece over, you may have to use a longer bolt but see if it will tighten down the dist. If it does, go get you a knew hold down or just take one off another V8 Chevy motor. If the dist. gasket is missing or torn up you should have a small oil leak. Good luck.
__________________
1969 Chevy SWB Big Block - Under the knife as of 12/26/2011
1989 Chevy Silverado, 4X4 - Daily Driver
1996 Chevy Suburban K1500 - 4-Wheeler, Campin Truck
1968 Chevrolet Impala Sport Coupe - 327/350hp, TH400, all original.
Members I've met: BamaBaxter,

My Build: http://67-72chevytrucks.com/vboard/s...d.php?t=500359
Camaro_nut2001 is offline   Reply With Quote
Old 06-04-2010, 10:09 AM   #15
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

okay if the gasket is no good how do i change it
81ratrodc10 is offline   Reply With Quote
Old 06-04-2010, 10:37 AM   #16
silvereagle07
Registered User
 
silvereagle07's Avatar
 
Join Date: Sep 2008
Location: Bailey, NC
Posts: 2,462
Re: distributer?

You have to remove the distributor to replace the gasket. Then you will have to set the timing but get a new hold down first. They are cheap. Do you have and pics of the way its mounted now?
__________________
Jeramy

'84 GMC project truck
'85 Chevy 4X4 SOLD
'07 Chevy Trailblazer SS

5th Annual SHPHC Car/Truck Show Pics
http://67-72chevytrucks.com/vboard/s...d.php?t=543605 UPDATED PICS! CHECK 'EM OUT
silvereagle07 is offline   Reply With Quote
Old 06-04-2010, 03:37 PM   #17
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

i dont have any right now but could get some
81ratrodc10 is offline   Reply With Quote
Old 06-04-2010, 04:31 PM   #18
68 TT
Still plays with trucks
 
68 TT's Avatar
 
Join Date: Jul 2009
Location: Spokane, WA
Posts: 3,556
Re: distributer?

I have seen distributor clamps that have been flattened out by people over tightening them over the years. The hold down bolt hole is only so deep so you can't tighten the bolt down enough any more to keep the clamp tight against the distributor base.

The fix is to put on another distributor clamp with more of the curve left in it.

This could be your problem or a combination of a bolt that is just barely too long and is not able to clamp down tight enough on the hold down to keep the distributor from moving on its own.
__________________
miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577
69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been
69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc
68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E
79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars
68 TT is offline   Reply With Quote
Old 06-04-2010, 04:41 PM   #19
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

cool maybe tomarrow ill take the bolt all the way out and look at it
81ratrodc10 is offline   Reply With Quote
Old 06-04-2010, 05:37 PM   #20
silvereagle07
Registered User
 
silvereagle07's Avatar
 
Join Date: Sep 2008
Location: Bailey, NC
Posts: 2,462
Re: distributer?

The clamp should have a slight bend. The originals are sprung steele and most chrome aftermarket clamps are cheap(they bend under pressure). You need a factory style with a bend or a beefy aftermarket clamp. The hold down on the right in the picture is how it should sit on the distributor.
Attached Images
 
__________________
Jeramy

'84 GMC project truck
'85 Chevy 4X4 SOLD
'07 Chevy Trailblazer SS

5th Annual SHPHC Car/Truck Show Pics
http://67-72chevytrucks.com/vboard/s...d.php?t=543605 UPDATED PICS! CHECK 'EM OUT
silvereagle07 is offline   Reply With Quote
Old 06-04-2010, 05:44 PM   #21
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

Quote:
Originally Posted by silvereagle07 View Post
The clamp should have a slight bend. The originals are sprung steele and most chrome aftermarket clamps are cheap(they bend under pressure). You need a factory style with a bend or a beefy aftermarket clamp. The hold down on the right in the picture is how it should sit on the distributor.
from that pic i think my hold down is no good going to look for sure tomarrow
81ratrodc10 is offline   Reply With Quote
Old 06-08-2010, 06:50 PM   #22
81ratrodc10
house of chevy's
 
81ratrodc10's Avatar
 
Join Date: May 2010
Location: New milford, CT
Posts: 583
Re: distributer?

well i finally got around to looking at it today unscrewed the hold down and it was flat bought a new one put it on no more turning set the timing runs like a champ now thanx guys for all your help
__________________
1987 m1028 cucv d30
2001 chevy s10
2000 honda shadow sabre 1100


"it's going to be an interesting ride home"
81ratrodc10 is offline   Reply With Quote
Old 06-08-2010, 06:57 PM   #23
68 TT
Still plays with trucks
 
68 TT's Avatar
 
Join Date: Jul 2009
Location: Spokane, WA
Posts: 3,556
Re: distributer?

Quote:
Originally Posted by 81ratrodc10 View Post
well i finally got around to looking at it today unscrewed the hold down and it was flat bought a new one put it on no more turning set the timing runs like a champ now thanx guys for all your help
Glad it was something simple and that we could help.
__________________
miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577
69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been
69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc
68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E
79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars
68 TT is offline   Reply With Quote
Old 06-08-2010, 08:04 PM   #24
73chevyman
Registered User
 
73chevyman's Avatar
 
Join Date: Nov 2008
Location: Lusby, MD
Posts: 563
Re: distributer?

mine does the samething but i forgot to put the gasket in lol
__________________
http://67-72chevytrucks.com/vboard/group.php?groupid=37
73 C10 Fleetside
If it ain't a Chevy it's foreign
http://hotridesmag.com/
73chevyman is offline   Reply With Quote
Old 06-09-2010, 11:00 AM   #25
68 TT
Still plays with trucks
 
68 TT's Avatar
 
Join Date: Jul 2009
Location: Spokane, WA
Posts: 3,556
Re: distributer?

Quote:
Originally Posted by 73chevyman View Post
mine does the samething but i forgot to put the gasket in lol
That just goes to show you how little tolerance there is for tight enough and not quite enough when it comes to the distributor.
__________________
miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577
69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been
69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc
68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E
79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars
68 TT is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:22 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com