The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-22-2008, 08:14 PM   #1
boostin20
Registered User
 
boostin20's Avatar
 
Join Date: Oct 2008
Location: VA
Posts: 16
Exclamation Carb sizing question

I bought a 72 c10 last month and just put in a 350 with a RV cam. With the cam, it's only 20 or so horsepower over stock. A quadrajet 4bbl came on the old engine. I don't know what size it is, and I won't be around the truck to look until tomorrow. I put the old carb on the new engine and adjusted it at idle. When I open up 4 barrels (stomp the gas), the truck immediately falls on its face until I let off the pedal. My two questions are this:

1. What is the best size 4bbl carb for an engine with no more than 300hp?
2. What do I have to do (if you think I don't need a new carb) to resolve the falling on its face issue when the other 2 barrels open?

Last edited by boostin20; 12-22-2008 at 08:17 PM.
boostin20 is offline   Reply With Quote
Old 12-22-2008, 08:31 PM   #2
Pyrotechnic
Registered User
 
Pyrotechnic's Avatar
 
Join Date: Feb 2007
Location: Austin, TX
Posts: 3,930
Re: Carb sizing question

I had this issue when I upgraded the stock cam in a my motor. The issue is not carb airflow capacity, the issue is that your primary fuel metering is too lean. You will need to find a larger jet, or get a small drill bit set and drill out the one you have.

Also, be aware that these cams will like more timing than a stock cam will. About 34 total is a good place to start. Setting your timing to stock specs will make the motor run badly.

The average Q-Jet will flow 750 CFM which is good even for a mild big block.
__________________
1977 GMC Sierra Grande

Last edited by Pyrotechnic; 12-22-2008 at 08:31 PM.
Pyrotechnic is offline   Reply With Quote
Old 12-22-2008, 10:05 PM   #3
Sport/Truck
Sierra Grande Club
 
Sport/Truck's Avatar
 
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
Re: Carb sizing question

Quote:
Originally Posted by Pyrotechnic View Post
The average Q-Jet will flow 750 CFM which is good even for a mild big block.
Some will argue it's too big for a SBC...
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe.
Sport/Truck is offline   Reply With Quote
Reply

Bookmarks

Tags
4bbl, adjustment, carb, problems, quadrajet

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com