The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-17-2015, 12:30 PM   #1
Wyfogy
Registered User
 
Join Date: Jan 2015
Location: Gillette Wyoming
Posts: 4
Exclamation 67 c10 problem running

I have a 67 c10 that has a mildly built 355 and turbo 350 transmission. The engine has an edelbrock performer intake and 600 cfm edelbrock 1406. Every time i accelerate hard and accelerate for a while like peeling out of a parking lot the truck dies when i come to a stop at idle. It will go away after a while then come back. I cant figure out what it is. I have all the vacuum line hooked up correctly. It has a brand new msd distributor, i just rebuilt the carb, has brand new fuel line, tank, pump. No power steering or power brakes. Its a hot rod and i want to drive it like one. Please help me.
Wyfogy is offline   Reply With Quote
Old 03-17-2015, 12:47 PM   #2
carsonmx114
Registered User
 
Join Date: Feb 2015
Location: fort payne
Posts: 20
Re: 67 c10 problem running

Sounds like you're rich on the top. The engine is loading up under full throttle then when you come to an idle it's stalling. I have lots of carb experience on bikes but almost none on vehicles so someone else on here may have a better idea. I'd rip it across a parking lot or somewhere and let it die then look at a spark plug. Also will it restart quicker after it stalls if you press the gas pedal? If so that's another clue that it's loading up.
carsonmx114 is offline   Reply With Quote
Old 03-17-2015, 01:16 PM   #3
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 67 c10 problem running

You got a fuel regulator?
Eddy carbs don't like more than 5 psi pressure.
Also might be timing!
What's your initial timing?
Where is your vac pot hooked to?

Last edited by geezer#99; 03-17-2015 at 01:22 PM.
geezer#99 is offline   Reply With Quote
Old 03-17-2015, 05:02 PM   #4
Wyfogy
Registered User
 
Join Date: Jan 2015
Location: Gillette Wyoming
Posts: 4
Re: 67 c10 problem running

No regulator and dist. Vacuum is hooked to the timed port on the carb and the truck will run perfect if i dont rod the piss out of it but if i accelerate hard fast and long then when i slow down and come to an idle it then starts acting up. Why woul it do this only when i drive it hard?
Wyfogy is offline   Reply With Quote
Old 03-17-2015, 05:05 PM   #5
Wyfogy
Registered User
 
Join Date: Jan 2015
Location: Gillette Wyoming
Posts: 4
Re: 67 c10 problem running

And i tried starting it back up and revved it up to maybe blow stuff out of there but that didnt work. It just kept doing the same thing. I let it sit for hours and still nothing.
Wyfogy is offline   Reply With Quote
Old 03-17-2015, 05:32 PM   #6
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 67 c10 problem running

When you work it hard you get higher fuel pressure and volume. You're using the fuel until you slam the throttle closed. At that point you're flooding a bit. Makes it run rough. Lowers your idle.
You need to lower your float level.
Another problem you might have is your timing.
What's your initial timing and what rpm are you idling at?
geezer#99 is offline   Reply With Quote
Old 03-17-2015, 05:49 PM   #7
Wyfogy
Registered User
 
Join Date: Jan 2015
Location: Gillette Wyoming
Posts: 4
Re: 67 c10 problem running

12-1400 and idk the timing. It ran good where i had it set it ran really good. So maybe instead of having 7/16 float i shoild have 1/2?
Wyfogy is offline   Reply With Quote
Old 03-17-2015, 06:01 PM   #8
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 67 c10 problem running

At your elevation you need as much initial timing as your motor likes and still starts hot.
Get a timing light and start your initial at 16 and increase it 2 degrees at a time until it labours when starting. Then back it off 2 degrees.
At 12-1400 rpm you're well into the mechanical timing in the dizzy. The mechanical usually starts working at 850 rpm.
Don't bother with the carb yet!
geezer#99 is offline   Reply With Quote
Old 03-18-2015, 01:23 AM   #9
swamp rat
Registered User
 
swamp rat's Avatar
 
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
Re: 67 c10 problem running

12-1400 is way too high for idle, your off the idle circut in into the accelerator circut, need to be about 750-800.
__________________
Mike.

Swamp Rat build thread :
http://67-72chevytrucks.com/vboard/s...d.php?t=595019

72 3/4T 4X4
4" BDS Lift
33" BFG's
swamp rat is offline   Reply With Quote
Reply

Bookmarks

Tags
accelerating, problems, running, small block

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:11 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com