Squaring up Cab? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Dodge68charger · 05-02-2023, 01:01 AM

Hey Guys Just Wondering What The Best Way To Square Up The Cab To The Frame On My 69 C10 Is?

Any Tips Or Tricks or Places To Measure From.

Thanks
Posted via Mobile Device

**Palf70Step** · 05-02-2023, 10:18 AM

I cross measured from the outside edges of firewall to the end of the frames. I used one of these ribs on each side of the firewall as the starting point and went to the farthest point on the front edge of the frame

**Grumpy old man** · 05-02-2023, 11:09 AM

This video should help .

https://www.youtube.com/watch?v=j7n_W1IxU_s

hugger6933 · 05-04-2023, 09:48 PM

Measure from the inner rocker to the frame use the same spots for both sides or an X measurement is always a good method like for instance measure the drivers rear inner rocker to the right front fender mount. Do it opposite on the other side the measurements should be the same remember if you have to move go only HALF of the number needed. Jim

Willie Makeit · 05-05-2023, 08:54 AM

I start the cab mount bolts and leave them loose then hang the doors, then fenders & rad support. once everything is bolted up and square THEN torque the cab mount bolts

05-02-2023, 01:01 AM	#1
Dodge68charger Registered User Join Date: Jul 2014 Location: Washington Posts: 533	Squaring up Cab? Hey Guys Just Wondering What The Best Way To Square Up The Cab To The Frame On My 69 C10 Is? Any Tips Or Tricks or Places To Measure From. Thanks Posted via Mobile Device

05-02-2023, 10:18 AM	#2
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 46,669	Re: Squaring up Cab? I cross measured from the outside edges of firewall to the end of the frames. I used one of these ribs on each side of the firewall as the starting point and went to the farthest point on the front edge of the frame Attached Images __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God! Last edited by Palf70Step; 05-02-2023 at 10:26 AM.

05-02-2023, 11:09 AM	#3
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: Squaring up Cab? This video should help . https://www.youtube.com/watch?v=j7n_W1IxU_s __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop

05-04-2023, 09:48 PM	#4
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,257	Re: Squaring up Cab? Measure from the inner rocker to the frame use the same spots for both sides or an X measurement is always a good method like for instance measure the drivers rear inner rocker to the right front fender mount. Do it opposite on the other side the measurements should be the same remember if you have to move go only HALF of the number needed. Jim

05-05-2023, 08:54 AM	#5
Willie Makeit Registered User Join Date: Oct 2013 Location: Alabama Posts: 1,206	Re: Squaring up Cab? I start the cab mount bolts and leave them loose then hang the doors, then fenders & rad support. once everything is bolted up and square THEN torque the cab mount bolts



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.