The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-15-2010, 08:08 PM   #1
Gibson
Registered User
 
Gibson's Avatar
 
Join Date: Jul 2009
Location: Maryville, TN
Posts: 132
Question Instrument cluster harness pins - electrical question

I may know what causes this - but wanted to check with you guys and make sure.

So you know how a lot of the components in the instrument cluster share a common ground? (like all the illumination bulbs all share a ground) Well, I was mapping out the circuit on the back of the cluster cause I'm about to do some modifications - and I noticed something weird. I was using my multimeter on the Highbeam bulb trying to figure out which of the leads was the ground. So I tested for continuity with the chassis thinking "Whichever one has continuity with he chassis will be the ground"

But BOTH pin leads in the harness clip have continuity with the chassis! Is this because it is finding continuity back through its positive pin, then through a splice somewhere, then through a bulb somewhere to that bulb's negative side, and then to the ground/chassis?

I started testing the other pins in the harness and noticed a vast majority short out to the chassis (apparently).

If so, is there a simple way to figure out which of these lead are actually grounds, and which ones are just working their way back through the wiring somewhere?



Thanks!
Gibson is offline   Reply With Quote
Old 01-15-2010, 08:53 PM   #2
95 S_Trucker
Registered User
 
95 S_Trucker's Avatar
 
Join Date: Oct 2009
Location: .
Posts: 2,178
Re: Instrument cluster harness pins - electrical question

were you just using an audible continuity tester?

if you were, the meter was going through the bulb as well.



use an ohm meter and whichever lead has the lowest resistance to ground would be ground.
95 S_Trucker is offline   Reply With Quote
Old 01-16-2010, 09:54 AM   #3
Gibson
Registered User
 
Gibson's Avatar
 
Join Date: Jul 2009
Location: Maryville, TN
Posts: 132
Smile Re: Instrument cluster harness pins - electrical question

Ah - gotcha. That works! Thanks!
Gibson is offline   Reply With Quote
Old 01-16-2010, 10:50 PM   #4
glock35ipsc
Next project: 1970 K10
 
glock35ipsc's Avatar
 
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
Re: Instrument cluster harness pins - electrical question

On the highbeam bulb, only one lead will map directly to the harness connector without stopping off anywhere else. But the ground will likely be a ground for many other bulbs and possibly a few gauges as well on its way to the harness connector.
__________________
Bob

1970 Chevy K10 LWB "Goldie" 350/TH350 next project!!
1981 Chevy C10 LWB 355/TH350 - My son's truck

LS SWAP FORUM! Tons of LS swap info here!
PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET!
CLICK HERE FOR THE FAQ INDEX by KRUE

Last edited by glock35ipsc; 01-16-2010 at 10:51 PM.
glock35ipsc is offline   Reply With Quote
Old 01-17-2010, 12:38 AM   #5
95 S_Trucker
Registered User
 
95 S_Trucker's Avatar
 
Join Date: Oct 2009
Location: .
Posts: 2,178
Re: Instrument cluster harness pins - electrical question

it sounds like you got it figured out, but if you are still having issues you could pull all the bulbs out and then test
95 S_Trucker is offline   Reply With Quote
Old 01-17-2010, 01:00 AM   #6
Gibson
Registered User
 
Gibson's Avatar
 
Join Date: Jul 2009
Location: Maryville, TN
Posts: 132
Re: Instrument cluster harness pins - electrical question

Quote:
Originally Posted by 95 S_Trucker View Post
it sounds like you got it figured out, but if you are still having issues you could pull all the bulbs out and then test
Yeah - it worked a trick - resistance was the correct way to go. And I also will try the "remove the other bulbs" thing if it gives me additional trouble. Thanks guys!
Gibson is offline   Reply With Quote
Reply

Bookmarks

Tags
electrical, gauge, instrument, multimeter

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:29 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com