|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-25-2023, 07:40 PM
|
#1 |
|
Registered User
Join Date: Nov 2014
Location: The Old Dominion
Posts: 52
|
Transmission Hump Height
Is the trans hump pictured low or high? I have a base '60 Apache with a three speed manual. I thought they came with the low hump but the rubber mat I just bought is too small so it has me thinking....
|
|
|
|
03-25-2023, 08:39 PM
|
#2 |
|
Registered User
 
Join Date: Sep 2022
Location: Eugene, OR
Posts: 490
|
Re: Transmission Hump Height
That looks considerably taller than mine, which I believe is a low hump.
|
|
|
|
|
03-25-2023, 09:15 PM
|
#3 |
|
Registered User
Join Date: Dec 2019
Location: Oregon
Posts: 158
|
Re: Transmission Hump Height
You are both showing pictures of a high hump. Normally the high hump is bolted in and a low hump generally is welded in.
|
|
|
|
|
03-25-2023, 09:18 PM
|
#4 |
|
Senior Member
  
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,426
|
Re: Transmission Hump Height
Both of y'all have a high hump. The low hump has a step up at the rear.
The low hump was bolted in on 60-63 floors.
__________________
Christian Carpenter 1963 C10 - Frankentruck 283, 3 speed with overdrive Overdrive wiring here1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson |
|
|
|
|
03-26-2023, 06:44 AM
|
#5 |
|
Registered User
Join Date: Nov 2014
Location: The Old Dominion
Posts: 52
|
Re: Transmission Hump Height
Thanks to all who responded. So is it normal to have a 3 speed manual and a high hump on a '60? From what I read it should be a low hump from the factory. This is a one owner (family) vehicle that I don't believe has ever been modified before it came to me.
|
|
|
|
|
03-26-2023, 09:40 AM
|
#6 |
|
Senior Member
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,426
|
Re: Transmission Hump Height
I'm not sure on that, but it's definitely plausible. The front section of the tunnel different between high and low, so if it's been changed in the past, you probably would be able to tell
__________________
Christian Carpenter 1963 C10 - Frankentruck 283, 3 speed with overdrive Overdrive wiring here1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson |
|
|
|
|
03-26-2023, 08:10 PM
|
#7 |
|
Registered User
Join Date: Jan 2017
Location: Derby Kansas
Posts: 358
|
Re: Transmission Hump Height
I have a 61 half ton with a 3 on the tree and a 62 one ton with the factory four speed. Other than the hole for the shifter on the one ton they are the same and both bolt in.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
