The 6.0 Silverado Build - Page 9 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

STOCKISH · 03-21-2010, 09:51 PM

Passenger side hits the frame a little (could trim the frame slightly and be fine) and the drivers side points right at the lower section of the inside of the frame. I heard the 5.3 ones work but I dont know if the 6.0 manifolds point out away from the trans a little more to clear the 4l80e trans? Either way, I have spent way too much time and effort making this look nice to use my manifolds. If they looked like new and fit better I would absolutely use them but since they arent in very good shape anyway, I will just try to save up and get some headers. Glock35ipsc used the 5.3 manifolds on his and they look awesome. But, if we are using his swap as a guide my whole job so far looks sub-par. His turned out sick!!!

bigdnew · 03-21-2010, 10:10 PM

I to am studying his build. My plan was to send my manifolds out for jet coat because they worked for him. However, I did not figure the difference in fit between the 5.3 and our 6.0s

D.FENS · 03-21-2010, 10:20 PM

I read on one of the other forums (can't remember which one) that Chevy Performance makes an LSX header flange that fits BBC headers. The idea being you take a set of BBC C-10 headers (like maybe the $89.95 Summit cheapies), cut the flange off and have the LSX flange welded on.

http://www.yearone.com/serverfiles/f...9&cat=9&trk=22

The flanges are cheap enough, but does the LSx have the same exhaust port spacing as a big block?

STOCKISH · 03-21-2010, 10:55 PM

Mine may be different because my engine is from a van as well. I am not sure . The 5.3 manifolds will fit the 6.0 engine.

menace121978 · 03-22-2010, 08:05 AM

Josh, i think your are different because they came from a van. i have the stock manifolds and they fit fine. the driverside fits like a glove and the pass. side needs a little triming on the frame rail. i'd make a few calls to yards and see how much a set of stock manifolds WITHOUT the EGR tube is. i'd give you my set man but i really think shipping would be ridiculous. my s&p's should be here today so we'll see how those fit.

STOCKISH · 03-22-2010, 08:24 AM

As much as I dont want to spend the money, I think I just need to buy the headers. They'll fit good, and look great. As well as flow better.

Driveway Dreams · 03-23-2010, 11:16 PM

Do you need a little encouragement?
BUY
THEM!!

JohnC · 03-24-2010, 09:11 AM

Very subtle Gerald.

STOCKISH · 03-24-2010, 12:11 PM

PayPal me the money and I'll get them ordered right up buddy!

Driveway Dreams · 03-25-2010, 12:00 AM

Ok, how much are they?
.
.
.
.
.
.
.
.
Just send that total to me and,
I will buy them for you!

Cherub · 03-25-2010, 07:55 AM

you will deff not be disapointed

STOCKISH · 03-25-2010, 10:29 AM

Picked up a set of manifolds from a 6.0 truck and they fit fine. Guess I'll be using those for now.

menace121978 · 03-25-2010, 10:33 AM

sweet! what is left?

Jonboy · 03-25-2010, 10:37 AM

Sounds like it's about time for some tire burning goodness!!

bigdnew · 03-25-2010, 10:38 AM

happy to hear the stock truck manifolds will work, gives me hope.

STOCKISH · 03-25-2010, 11:58 AM

Quote:

Originally Posted by menace121978

sweet! what is left?

Wrap the harness once the harness wrap shows up, and fuel system, driveshaft and get exhaust hooked back up.

glock35ipsc · 03-25-2010, 04:18 PM

Yo Josh! It was good chatting with you on the phone!

I found the diagrams on my Photobucket account. Right click, "view image", then print them out. You can probably see them better that way. It might help also to take a pen or pencil and trace over the numbers and stuff to make them clearer, as they aren't very sharp.

STOCKISH · 03-25-2010, 04:36 PM

Thanks buddy! I appreciate it. Was good to talk to you as well. You too Dennis, thanks again for the help today. Man I love this forum.

glock35ipsc · 03-25-2010, 04:58 PM

Shoot me an email at glock35ipsc AT aim.com and I will email you an Excel spreadsheet I did of the cluster wiring between the 85 cluster and the 91 cluster.

menace121978 · 03-25-2010, 06:30 PM

same here... good chatting with ya! i mailed the fuel pipe fitting off today @1pm. 1st class usps. will be at your door monday!

hey Bob, Josh has your -an fittings now!

79gmc5.3 · 03-25-2010, 06:58 PM

Quote:

Originally Posted by 1972SuperCheyenne

Picked up a set of manifolds from a 6.0 truck and they fit fine. Guess I'll be using those for now.

Do they look like this? This is my P/S manifold, I had to cut this much off to clear the engine mount stand that mounts to the frame. Kept cutting until I found a hollow spot that is there for the egr I guess. I will have it welded this weekend but it clears now

Anyway keep things going looks good.

menace121978 · 03-25-2010, 07:43 PM

Quote:

Originally Posted by glock35ipsc

Yo Josh! It was good chatting with you on the phone!

I found the diagrams on my Photobucket account. Right click, "view image", then print them out. You can probably see them better that way. It might help also to take a pen or pencil and trace over the numbers and stuff to make them clearer, as they aren't very sharp.

jeez... can someone PLEASE put this in english

STOCKISH · 03-25-2010, 08:58 PM

Thats what I was thinking. It's not bad once you really look at it and see whats going on. My manifolds didnt have provisions for EGR or AIR

Driveway Dreams · 03-25-2010, 10:48 PM

Glad to hear you got the manifolds & they fit. That is awesome! Although this discussion made me feel left out. I didn't talk to you today.

STOCKISH · 03-26-2010, 07:47 AM

PM me your number, hell, I'll call you too!

03-21-2010, 09:51 PM	#201
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build Passenger side hits the frame a little (could trim the frame slightly and be fine) and the drivers side points right at the lower section of the inside of the frame. I heard the 5.3 ones work but I dont know if the 6.0 manifolds point out away from the trans a little more to clear the 4l80e trans? Either way, I have spent way too much time and effort making this look nice to use my manifolds. If they looked like new and fit better I would absolutely use them but since they arent in very good shape anyway, I will just try to save up and get some headers. Glock35ipsc used the 5.3 manifolds on his and they look awesome. But, if we are using his swap as a guide my whole job so far looks sub-par. His turned out sick!!! __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-21-2010, 10:10 PM	#202
bigdnew Never Satisfied Join Date: Sep 2009 Location: Sherman, Texas Posts: 360	Re: The 6.0 Silverado Build I to am studying his build. My plan was to send my manifolds out for jet coat because they worked for him. However, I did not figure the difference in fit between the 5.3 and our 6.0s __________________ 1973 4x4 Blazer- Parting Out 1986 LWB Silverado Undergoing LQ4/4L80E Swap '86 Build Thread:http://67-72chevytrucks.com/vboard/showthread.php?t=390566

03-21-2010, 10:20 PM	#203
D.FENS Registered User Join Date: Sep 2008 Location: Huntsville AL Posts: 284	Re: The 6.0 Silverado Build I read on one of the other forums (can't remember which one) that Chevy Performance makes an LSX header flange that fits BBC headers. The idea being you take a set of BBC C-10 headers (like maybe the $89.95 Summit cheapies), cut the flange off and have the LSX flange welded on. http://www.yearone.com/serverfiles/f...9&cat=9&trk=22 The flanges are cheap enough, but does the LSx have the same exhaust port spacing as a big block? Last edited by D.FENS; 03-21-2010 at 10:22 PM.

03-21-2010, 10:55 PM	#204
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build Mine may be different because my engine is from a van as well. I am not sure . The 5.3 manifolds will fit the 6.0 engine. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-22-2010, 08:05 AM	#205
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: The 6.0 Silverado Build Josh, i think your are different because they came from a van. i have the stock manifolds and they fit fine. the driverside fits like a glove and the pass. side needs a little triming on the frame rail. i'd make a few calls to yards and see how much a set of stock manifolds WITHOUT the EGR tube is. i'd give you my set man but i really think shipping would be ridiculous. my s&p's should be here today so we'll see how those fit. __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

03-22-2010, 08:24 AM	#206
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build As much as I dont want to spend the money, I think I just need to buy the headers. They'll fit good, and look great. As well as flow better. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-23-2010, 11:16 PM	#207
Driveway Dreams I have car A.D.D. Join Date: Feb 2009 Location: Greeley, Northern Colorado Posts: 4,147	Re: The 6.0 Silverado Build Do you need a little encouragement? BUY THEM!! __________________ -Gerald Building vehicles in memory of the first "car guy" I ever knew, my Grandpa. Bob Dunham 1935-2009. Rest in peace. 61 GMC Suburban SOLD The 86 build thread SOLD Are you a Colorado member?Click here.

03-24-2010, 09:11 AM	#208
JohnC Registered User Join Date: Feb 2009 Location: Oklahoma Posts: 7,461	Re: The 6.0 Silverado Build Very subtle Gerald.

03-24-2010, 12:11 PM	#209
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build PayPal me the money and I'll get them ordered right up buddy! __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-25-2010, 12:00 AM	#210
Driveway Dreams I have car A.D.D. Join Date: Feb 2009 Location: Greeley, Northern Colorado Posts: 4,147	Re: The 6.0 Silverado Build Ok, how much are they? . . . . . . . . Just send that total to me and, I will buy them for you! __________________ -Gerald Building vehicles in memory of the first "car guy" I ever knew, my Grandpa. Bob Dunham 1935-2009. Rest in peace. 61 GMC Suburban SOLD The 86 build thread SOLD Are you a Colorado member?Click here. Last edited by Driveway Dreams; 03-25-2010 at 12:00 AM.

03-25-2010, 07:55 AM	#211
Cherub Registered User Join Date: Feb 2008 Location: Houston Posts: 970	Re: The 6.0 Silverado Build you will deff not be disapointed __________________ 2014 LTZ Z71 Silverado 82 C15 LQ4/4L80E Conversion 78 Suburban build (SOLD) 83 4x4 Suburban(SOLD) 82 C15 (my first truck)

03-25-2010, 10:29 AM	#212
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build Picked up a set of manifolds from a 6.0 truck and they fit fine. Guess I'll be using those for now. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-25-2010, 10:33 AM	#213
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: The 6.0 Silverado Build sweet! what is left? __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

03-25-2010, 10:37 AM	#214
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: The 6.0 Silverado Build Sounds like it's about time for some tire burning goodness!! __________________ 1974 Jimmy- 5.3/4L80e/NP241

03-25-2010, 10:38 AM	#215
bigdnew Never Satisfied Join Date: Sep 2009 Location: Sherman, Texas Posts: 360	Re: The 6.0 Silverado Build happy to hear the stock truck manifolds will work, gives me hope. __________________ 1973 4x4 Blazer- Parting Out 1986 LWB Silverado Undergoing LQ4/4L80E Swap '86 Build Thread:http://67-72chevytrucks.com/vboard/showthread.php?t=390566



Register or Log In To remove these advertisements.

03-25-2010, 04:18 PM	#217
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,685	Re: The 6.0 Silverado Build Yo Josh! It was good chatting with you on the phone! I found the diagrams on my Photobucket account. Right click, "view image", then print them out. You can probably see them better that way. It might help also to take a pen or pencil and trace over the numbers and stuff to make them clearer, as they aren't very sharp. __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE Last edited by glock35ipsc; 03-25-2010 at 04:19 PM.

03-25-2010, 04:36 PM	#218
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build Thanks buddy! I appreciate it. Was good to talk to you as well. You too Dennis, thanks again for the help today. Man I love this forum. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-25-2010, 04:58 PM	#219
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,685	Re: The 6.0 Silverado Build Shoot me an email at glock35ipsc AT aim.com and I will email you an Excel spreadsheet I did of the cluster wiring between the 85 cluster and the 91 cluster. __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE

03-25-2010, 06:30 PM	#220
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: The 6.0 Silverado Build same here... good chatting with ya! i mailed the fuel pipe fitting off today @1pm. 1st class usps. will be at your door monday! hey Bob, Josh has your -an fittings now! __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

03-25-2010, 08:58 PM	#223
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build Thats what I was thinking. It's not bad once you really look at it and see whats going on. My manifolds didnt have provisions for EGR or AIR __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

03-25-2010, 10:48 PM	#224
Driveway Dreams I have car A.D.D. Join Date: Feb 2009 Location: Greeley, Northern Colorado Posts: 4,147	Re: The 6.0 Silverado Build Glad to hear you got the manifolds & they fit. That is awesome! Although this discussion made me feel left out. I didn't talk to you today. __________________ -Gerald Building vehicles in memory of the first "car guy" I ever knew, my Grandpa. Bob Dunham 1935-2009. Rest in peace. 61 GMC Suburban SOLD The 86 build thread SOLD Are you a Colorado member?Click here.

03-26-2010, 07:47 AM	#225
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: The 6.0 Silverado Build PM me your number, hell, I'll call you too! __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

Register or Log In To remove these advertisements.