The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Racing and high performance (trucks haulin more than hay)

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-25-2009, 07:30 PM   #1
69trk
Registered User
 
69trk's Avatar
 
Join Date: Oct 2006
Location: bridgecreek ok.
Posts: 1,214
077 aluminum heads

What do you guys think about a set of aluminum 077 gm heads? rectangle port with valves, studs, guide plates and have been ported for $750.00 dissassembled. 225 /188 valves. do you think they will flow better than my 14097088 iron heads with tons of work done to them? And if so, is this a good price? thanks
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=494388

431 big block times, changed to a 6.0 ls with turbo
1.58- 60'
7.18- 1/8th mile@95.18
11.37- 1/4 @115.81
69trk is offline   Reply With Quote
Old 07-26-2009, 11:13 AM   #2
Marv D
Registered Truck Offender
 
Marv D's Avatar
 
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
Re: 077 aluminum heads

I am not a bigblock guy at all, but if that is for the pair of bare castings, that is still pretty cheap! However, if it's not the ultimate head that you want,, it's a waste. As far s what flows better,, if neiher have been on a flow bench,, it's a guess. I've seen "tons of work" not help sbc heads one bit (in fact hurt low lift volocity and flow so bad it makes them useless for anything other than WFO at the track) and I've seen it turn them into some really sweet heads. So again were back to the flow bench.
__________________
Still playin with trucks, even at my age!

When you're dead, it's only a problem for the people around you, because you don't know you're dead.
.....It's kinda the same when your STUPID.


I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral.
Marv D is offline   Reply With Quote
Old 07-26-2009, 05:44 PM   #3
Super73
Registered User
 
Super73's Avatar
 
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
Re: 077 aluminum heads

Flow benches give you a lot of good info, but they are not the end all be all.. To Marv's point there is good info to be had with them, but flow numbers do nothing if there is a huge valve with bad valve angles and hogged out ports compared to a head that has a little less flow numbers yet smaller port/valves to keep velocity up. Reversion can be the enemy at low RPM. Add to that, the cam profile needs to be matched to the heads, intake and exhaust.

With out comparing the full setup it's a crap shoot.
__________________
------Motor---------------Bottle
60'---1.53---------------1.41
1/8---6.58 @ 105.92----5.87 @ 118.41
1/4---10.38 @ 126.97----9.24 @ 142.49

Last edited by Super73; 07-26-2009 at 05:45 PM.
Super73 is offline   Reply With Quote
Old 07-26-2009, 08:08 PM   #4
Ont67shortbox
Registered User
 
Join Date: May 2003
Location: Ontario
Posts: 279
Re: 077 aluminum heads

I would take them to a machine shop first and have them checked.As mentioned porting can hurt if not done correctly,your also dealing with 40 yr old technology,there are some excellent heads out now at decent prices that may flow better,with more advancements than the 077s.

Last edited by Ont67shortbox; 07-26-2009 at 08:09 PM.
Ont67shortbox is offline   Reply With Quote
Old 07-27-2009, 03:24 PM   #5
BossHogg69
motor exploder
 
BossHogg69's Avatar
 
Join Date: Mar 2009
Location: Pittsburgh, PA
Posts: 2,346
Re: 077 aluminum heads

Those are the "winters" big block heads. They were produced as a racing piece and where the shiznit in the 70's. Even against some of todays stuff, they perform well, esp the factory iron rectangle ports. I think the intake ports are like 295cc or so, and a C-shaped exhaust port. Of course, if you know your 088's perform well and are happy with them, the only advantage you'll likely reap would be the weight reduction. Depending on what's been done to your 088's I'm not sure you'd be blown away by swapping heads.
__________________
Adam

1969 Chevy CST/10 stepside, DART Big M/TREMEC Magnum Extreme/3.73's w/Detroit Truetrac
1965 Chevy Bel Air Wagon (daily driver), 327/TH350,10 bolt w/3.08's
1961 Chevy Bel Air Sport Coupe, ZZ454/M21/9" rear w/3.50's & Detroit Truetrac
2005 GMC 1500 ccsb 2wd, 6.0L/4L65e/3.73 G80
2006 GMC 2500HD ccsb 4x4, DMax LBZ/Allison 6spd/4.56's w/Detroit TrueTrac

Use the SEARCH function on this forum - it is your friend!!
BossHogg69 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:59 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com