The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > All 4x4 Tech & Off Roading

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-16-2013, 03:14 PM   #1
72blue
Registered User
 
72blue's Avatar
 
Join Date: Feb 2009
Location: arroyo grande, ca
Posts: 206
72 frame rivets?

Hi all! my name is James and I have a 72 k10 swab pickup. I got the truck back in 06 and have put a ton of time and money in it. The engine (sbc 383) is currently out getting a roller cam (last one was not ideal for street) so I'm tying up loose ends on things I never finished (glove box, ac, etc.)

To the matter at hand. I had the body off early on in this build, frame completely bare and cut ALL rivets off frame and powder coated the frame brackets and painted the frame. Brackets are bolted back in with grade 8 bolts (7/16). I've been told by some that I shouldn't have done this cause rivets are stronger/tighter fitting. Did I mess this up? Should I look for a place that can install new rivets? I am not concerned with the engine and trans cross members, however the front, rear, and main crossmember (the one that holds the frame together and the rear axle front spring hangers).

Help what should I do?
Posted via Mobile Device
Posted via Mobile Device
__________________
James
72blue is offline   Reply With Quote
Old 06-16-2013, 06:15 PM   #2
Bigdav160
Registered User
 
Bigdav160's Avatar
 
Join Date: Apr 2011
Location: Klein Texas
Posts: 3,852
Re: 72 frame rivets?

Bolts, like rivets allow some flex in the frame. That's a good thing.

Rivets, however, can't fall out like bolts.

Rivets are available but I don't know how hard they would be to install.

I'd use bolts with loctite and check them for torque occasionally.
__________________
My Classics:
'72 K20 Suburban + '65 Dodge Town Wagon
'72 Corvette Roadster +'67 Corvette Roadster
'73 Z-28 Camaro
'63 Ford SWB Uni Pickup
'50 Ford Coupe
Bigdav160 is offline   Reply With Quote
Old 06-16-2013, 06:55 PM   #3
vidman
Registered User
 
vidman's Avatar
 
Join Date: Jun 2012
Location: Fitchburg,Mass
Posts: 737
Re: 72 frame rivets?

Of all the builds that I have done in the last 40 years that I have cut off the rivets and replaced with bolts, I have had O problems with them falling out. Just use some blue loctite and some grade 8 hardware and you will be good to go..
__________________
62 Willys 4wd Pickup : 72 C-10 swb 504 stroker 09 Taco 3" lift 33" tires: 90 K-5 blazer (plow truck): RIP Ross Little brother
vidman is offline   Reply With Quote
Old 06-16-2013, 07:06 PM   #4
CUSTOM/10
Senior Member
 
CUSTOM/10's Avatar
 
Join Date: May 2003
Location: Sandown, NH
Posts: 2,784
Re: 72 frame rivets?

I have done both, bolts & rivets. But I used wheel studs nut regular bolts. For one the head looks like a rivet, two they are knurled so if you have the correct size they press into the whole making a very tight fit. But they are expensive and you have to get the right ones.

I have also replaced rivets, not easy but can be done. I made a tool to peen & form the back side of the rivet the goes into my pneumatic hammer. The rivet needs to be cut to just the correct length so when peened it fits tight ! The rivet also expands making it very tight. You need to have a way to clamp the rivet in place, heat the back side cheery red and peen it. It may take a few tries to complete but looks original when done. I used ( Still have a box ) of 7/16 rivets, the originals were 11/32 I believe, but very hard to find.

I never had any issues with either !

Hope this helps !
Gary
__________________
Gary
72 SWB 4x4

My 72 SWB Build
http://67-72chevytrucks.com/vboard/s...d.php?t=259859
CUSTOM/10 is offline   Reply With Quote
Old 06-16-2013, 11:53 PM   #5
72blue
Registered User
 
72blue's Avatar
 
Join Date: Feb 2009
Location: arroyo grande, ca
Posts: 206
Re: 72 frame rivets?

Thanks to allof you for your replies. This gives me some confidence in what I have already done. Now wish me luck in getting my engine back together and the truck out on the road (or off roading)

James
Posted via Mobile Device
__________________
James
72blue is offline   Reply With Quote
Reply

Bookmarks

Tags
1972, 4x4, frame, rivets, swb

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:50 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com