Youtube channel with how to videos on metal work

[May70]

Those following my build thread have seen me install a new floor pan and I have finished the passenger side cab corner, pillars, inner & outer rocker.

I decided I would try to record the Drivers Side from start to finish so there was a complete step by step video series on this. I know there are a lot of bits and pieces on youtube and a lot of good threads but the videos skip a lot of steps. I know it would have made my life easier so here you go.

https://www.youtube.com/channel/UCkS..._as=subscriber

[SD69C10]

Thank you, just subscribed and will check them out. Have to replace the inner and outer rocker panels on my 69 and will be the first time ever doing anything like this.

[dagnabbitt]

Subscribed! I too have to do this work on my 68 and my 70.

It is true that there are a lot of videos out there, but it's nice to have one from a board member, it somehow lends credibility to it for me.

[Fbks_Cruiser]

Thanks! This is a job in my future. I’ll check it out.

[rechinca]

Just downloaded to watch them tomorrow on my down time.

[May70]

Thanks, I posted another video last night finishing up the pillar. Showed some shrinker techniques.

[Getter-Done]

Subbed to watch this weekend










.

[May70]

Tomorrow im hoping to seal the inside of the pillar and cab corner so by the weekend you should see a lot of progress. Warmest day weatherman is calling for a while here....

[May70]

I managed to get the cab corner/pillar finished up for the most part and uploaded two more videos. There are 4 parts and 1.5 hrs of video total which I think give a pretty good walk through of everything.

Now on to the outer rocker!

[May70]

I uploaded part 1 of the outer rocker video. This one doesnt look like it will take nearly as much work to get done as the PS did.

https://www.youtube.com/watch?v=dY6qtxZ9-9g&t=834s

Hopefully these help people years to come....

[May70]

Second part of the rocker video is uploaded

https://www.youtube.com/watch?v=KEmunwBMAlg




.

[Fbks_Cruiser]

Thanks. I’ve been watching.

[May70]

Originally Posted by Fbks_Cruiser

Thanks. I’ve been watching.

Thanks for the support!!
Posted via Mobile Device

[best view]

Watched every one also

[dagnabbitt]

Been watching, good stuff. Like the ironing board toolbench too, very relatable!

[May70]

Originally Posted by best view

Watched every one also

Originally Posted by dagnabbitt

Been watching, good stuff. Like the ironing board toolbench too, very relatable!

Thanks for the support! I hope to see this grow.

I'm going to try and get a how to video on all the common places so ill have to do a second cab to get one of the floor pan and front pillar. I've already had two people contact me to do theirs but they were kind of far away and if I did one for someone Id want them to be close. That way they can come often to see progress etc....

[franken]

Nice. Seems like an honest demonstration of the issues with the replacement parts, which is often not shown.

[May70]

Originally Posted by franken

Nice. Seems like an honest demonstration of the issues with the replacement parts, which is often not shown.

That is one of the exact reasons why I started this.

[bigmac73]

Originally Posted by May70

Thanks for the support! I hope to see this grow.

I did one for someone Id want them to be close. That way they can come often to see progress etc....

you got my attention , what would be your number for floor pan , cab corners and rockers and a few other odds and ends?

[May70]

Part 3 of 3 is now up for the rocker panel install, turned out nice!!!

https://www.youtube.com/watch?v=F9viASzV8Yg




.

[May70]

I just uploaded part 1 (of 2) on the inner rocker.

In part 1 I show how I make my own inner rocker from scratch and also how it ties into the rest of the cab. Part 2 I will show how to install the inner rocker.

https://www.youtube.com/watch?v=4d6oxnMvrDc



.

[Getter-Done]

Great Channel

Your doing a great job!!








.

[Osker]

Thank you for these YouTube videos. They are invaluable learning opportunities and references that have helped me tremendously as I work on a 72 cab. Your explanations, techniques and detailed documenting helps me understand and rethink my approach. Motivating and inspiring. I'm learning as I go and this is one of the greatest resources out there. I'm not doing a total floor replacement but everything you cover is extremely helpful. Thanks again and keep up the great work!

[bubbasimms]

Subscribed and have really enjoyed your videos. Did you make a video on the full floor replacement?

[May70]

Originally Posted by Getter-Done

Great Channel

Your doing a great job!!

.

Thanks Getter-Done!

Originally Posted by Osker

Thank you for these YouTube videos. They are invaluable learning opportunities and references that have helped me tremendously as I work on a 72 cab. Your explanations, techniques and detailed documenting helps me understand and rethink my approach. Motivating and inspiring. I'm learning as I go and this is one of the greatest resources out there. I'm not doing a total floor replacement but everything you cover is extremely helpful. Thanks again and keep up the great work!

Thank you for the words. Appreciate the support.

Originally Posted by bubbasimms

Subscribed and have really enjoyed your videos. Did you make a video on the full floor replacement?

Thanks! Not yet. I might have another cab coming and I will make a video series on that if I get it.