What did you do today not on your truck... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Andy4639 · 11-16-2020, 08:54 PM

I bought this one for $1000.00. Going to some friends down at the beach. He is on Oxygen all the time so it's going be for him to ride around in the yard with his grand daughter.
I installed a 400amp Alltrax controller and ITS switch this past spring.

I'm doing the brakes on it now. Cables were froze up on it had to cut them out with my saw all. New cables ordered. Batteries were still wet but had no water in them. I hope I caught them in time to save them. There only 3 years old.

72c20customcamper · 11-17-2020, 06:15 PM

Bath is moving along. Scraped of the old mastic and sealed the plywood , I'm installing radiant heat and it needs a 1/4 inch of mortar or self leveling underlayment I'm going with the self leveler. Have all the expansion joints in and sealed . Made the joints out of 1/2 inch foam board that's about an inch tall I'll just trim it flush to the underlayment and install my flooring . I'm using water proof laminate , if I was tiling I'd just put the heat mesh down and apply thinset.

**Getter-Done** · 11-18-2020, 11:36 PM

Quote:

Originally Posted by Andy4639

I bought this one for $1000.00. Going to some friends down at the beach. He is on Oxygen all the time so it's going be for him to ride around in the yard with his grand daughter.
I installed a 400amp Alltrax controller and ITS switch this past spring.

I'm doing the brakes on it now. Cables were froze up on it had to cut them out with my saw all. New cables ordered. Batteries were still wet but had no water in them. I hope I caught them in time to save them. There only 3 years old.

.

Andy4639 · 11-19-2020, 09:32 PM

Quote:

Originally Posted by Getter-Done

.

I finished up the cart today. New brake cables. The passenger side hub cost me 2 days and $75.00 for a used axle & hub. I had to cut & grind the old out. It's back on the ground though and ready to go. Batteries are holding a charge so far but I haven't rode it but just enough to make sure it ran good.

72c20customcamper · 11-22-2020, 10:53 AM

Installed two new shower heads yesterday . This morning I drilled out both of the water restrictors . Felt like I had to run around the stream to get wet . What's the sense of less water per minute when you have to take a much longer shower .

11-16-2020, 08:54 PM	#1
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,936	Re: What did you do today not on your truck... I bought this one for $1000.00. Going to some friends down at the beach. He is on Oxygen all the time so it's going be for him to ride around in the yard with his grand daughter. I installed a 400amp Alltrax controller and ITS switch this past spring. I'm doing the brakes on it now. Cables were froze up on it had to cut them out with my saw all. New cables ordered. Batteries were still wet but had no water in them. I hope I caught them in time to save them. There only 3 years old. Attached Images __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

11-17-2020, 06:15 PM	#2
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,238	Re: What did you do today not on your truck... Bath is moving along. Scraped of the old mastic and sealed the plywood , I'm installing radiant heat and it needs a 1/4 inch of mortar or self leveling underlayment I'm going with the self leveler. Have all the expansion joints in and sealed . Made the joints out of 1/2 inch foam board that's about an inch tall I'll just trim it flush to the underlayment and install my flooring . I'm using water proof laminate , if I was tiling I'd just put the heat mesh down and apply thinset. Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

11-22-2020, 10:53 AM	#5
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,238	Re: What did you do today not on your truck... Installed two new shower heads yesterday . This morning I drilled out both of the water restrictors . Felt like I had to run around the stream to get wet . What's the sense of less water per minute when you have to take a much longer shower . __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary. Last edited by 72c20customcamper; 11-22-2020 at 08:41 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.