|
Re: Used Parts Build
Also... Ordered these!
http://i20.photobucket.com/albums/b2...518_120722.jpg They should fit really well. I made my notch too high initially and want to bring it down. Got them from Applied Racing Technologies. They are 2x3x.120 and a bit lighter duty than I want but I will tie them to my four link cross member with some 1.5x.120 tube. The rear of the frame only supports half the bed and the fuel tank. I think it will be fine. Plus each rail weighs significantly less than each of my damn over built notches. http://i20.photobucket.com/albums/b2...518_120944.jpg |
Re: Used Parts Build
I took a day off and worked through the weekend to try to get some work done to it. Ended up being really hot so I didn't get as much done as I wanted. Here are the pics:
Pushed my brother's Nova out, cleaned the garage, and pushed mine it. The differential is all jacked up and it took 4 people to push it up the driveway... http://i20.photobucket.com/albums/b2...616_095910.jpg Old backhalf http://i20.photobucket.com/albums/b2...616_114015.jpg http://i20.photobucket.com/albums/b2...616_132729.jpg Cutting the old backhalf off and found a wasp nest. Holy **** there were tons! http://i20.photobucket.com/albums/b2...616_133533.jpg http://i20.photobucket.com/albums/b2...616_145712.jpg |
Re: Used Parts Build
|
Re: Used Parts Build
Had to trim them down a bit to fit
http://i20.photobucket.com/albums/b2...616_154912.jpg http://i20.photobucket.com/albums/b2...617_155740.jpg Mock up http://i20.photobucket.com/albums/b2...616_230002.jpg |
Re: Used Parts Build
Capped the ends
http://i20.photobucket.com/albums/b2...617_182247.jpg Removed everything to make it easer to weld in http://i20.photobucket.com/albums/b2...618_150026.jpg Lovely temp to work in... http://i20.photobucket.com/albums/b2...618-162038.png |
Re: Used Parts Build
Weldable primer for all the parts that will be sandwiched together.
http://i20.photobucket.com/albums/b2...618_173034.jpg http://i20.photobucket.com/albums/b2...618_173041.jpg Started tacking http://i20.photobucket.com/albums/b2...618_200957.jpg I feel like I forget to mig weld since I have been tigging everything lately http://i20.photobucket.com/albums/b2...618_202919.jpg http://i20.photobucket.com/albums/b2...618_202940.jpg Laid out! http://i20.photobucket.com/albums/b2...618_223026.jpg |
Re: Used Parts Build
A pic with my gf for height reference.
http://i20.photobucket.com/albums/b2...618_222936.jpg Did it all in 3 days. Need to do all the tube work now. The front has 3 2x4's under the cross member because I need to swap out the oil pan still. |
Re: Used Parts Build
Love the fab work. Wish I could weld like that!
|
Re: Used Parts Build
The new rails look great. Glad to see you are back at it.
|
Re: Used Parts Build
Quote:
Quote:
|
Re: Used Parts Build
Still trying to figure out the tube work in the back. I don't have the funds to buy a tube bender at the moment so I am stuck with either the 90 degree bends I have or straight tube. Any input? I'd like to tie the bag mounts to each other across the center.
http://i20.photobucket.com/albums/b2...619_222318.jpg Burned in the back cross member: http://i20.photobucket.com/albums/b2...625_202642.jpg Its just a bit too tight to fit the blazer tank (thing is huge). I can raise it up thought and likely fit it under the bed floor still. http://i20.photobucket.com/albums/b2...625_210232.jpg |
Re: Used Parts Build
Screw photobucket.
Took another Chop/Metal Shaping class. https://farm5.staticflickr.com/4294/...cfc57f87_b.jpg Still working on my backhalf. Got it all tied in. https://farm5.staticflickr.com/4313/...1551d268_b.jpg Base for the gas tank in. Need to figure out my shocks and how to mount the gas tank next. https://farm5.staticflickr.com/4325/...69cffbc8_k.jpg https://farm5.staticflickr.com/4312/...88e6e994_k.jpg Watts link in https://farm5.staticflickr.com/4317/...14162f39_b.jpg [url=https://flic.kr/p/WLzYEC]https://farm5.staticflickr.com/4323/...39f1dd64_b.jpg |
Re: Used Parts Build
Some nice work....very cool
|
Re: Used Parts Build
Cool looking fab work. Was the class at Skoty Chops? I need to do a class like that.
|
Re: Used Parts Build
Quote:
Quote:
And since every post should have a picture...here is a stainless steel exhaust I did for my buddy's race car on Saturday. You can see the original muffler next to it. https://farm5.staticflickr.com/4318/...c8959cfd_b.jpg |
Re: Used Parts Build
Cool
|
Re: Used Parts Build
Got the bed assembled and squared on the frame. Going to build the rear mounts next. Aired it out for some quick pictures. Need to pull the engine and change the oil pan to get it all the way down.
[url=https://flic.kr/p/X39EAw]https://farm5.staticflickr.com/4312/...65c91b83_k.jpg https://farm5.staticflickr.com/4304/...eb0f3876_k.jpg https://farm5.staticflickr.com/4319/...855774ba_k.jpg |
Re: Used Parts Build
Nice!!
|
Re: Used Parts Build
Quote:
Remade my rear bed mounts: https://farm5.staticflickr.com/4409/...edc33b19_k.jpg https://farm5.staticflickr.com/4404/...06373acd_k.jpg https://farm5.staticflickr.com/4366/...6f8880e6_k.jpg Bed is on. Need to do one more set of mounts mid bed. Then doing some frame tubing and figure out the shock mounting. https://farm5.staticflickr.com/4432/...0b584f0e_k.jpg |
Re: Used Parts Build
Sweet......
|
Re: Used Parts Build
Finished all the bed mounts.
https://farm5.staticflickr.com/4342/...ac202ce3_h.jpg https://farm5.staticflickr.com/4381/...81e042fb_h.jpg Started playing with the hotside for my turbo set up. Getting tired of working on the frame and suspension at the moment. Luckily I have a ton of work to do... https://farm5.staticflickr.com/4358/...62ec9f4f_h.jpg |
Re: Used Parts Build
Got some parts and started working on the merge.
https://farm5.staticflickr.com/4374/...44a8ea71_h.jpg https://farm5.staticflickr.com/4397/...44261acc_h.jpg I don't have enough hands to hold it in place for the picture but it lines up. Need to tack it together and grind the bottom flush. Then I'll port the flange a bit and weld it all up. I bought a second tank of argon and flow meter because it was cheaper than buying a dual flow meter. |
Re: Used Parts Build
|
Re: Used Parts Build
Welded the cast iron to the stainless. Thought it came out good. There is tiny crack in along the edge of part of the weld. Going to grind it out and do it again.
https://farm5.staticflickr.com/4340/...fa964461_b.jpg https://farm5.staticflickr.com/4367/...857e224e_b.jpg Used the other half to keep it hot in between welding https://farm5.staticflickr.com/4411/...d8b30b29_b.jpg |
Re: Used Parts Build
Got both sides welded up. Ground out the area that looked liked it cracked on the first manifold. Not sure it was actually cracked once I ground it all back. Used the oven this time and preheated the manifolds to 450. Welded it up, then put it right back in the oven. Slowly lowered the heat over the next few hours. I used my infrared thermometer to make sure each side (cast vs stainless) was at the same temp before lowing the oven by 75 degrees each time. I looked them over this morning before work and didn't see any cracking.
https://farm5.staticflickr.com/4391/...c8d3c9a7_b.jpg Ordered a VS Racing 44mm wastegate, bellow, and a schedule 10 2'' to 1.5'' reducer to mount it with. |
| All times are GMT -4. The time now is 11:36 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com