Re: '55 International Metal/Body/Paint Work
 

The rest of the hood was straightened with the same process at the dent on the side.

http://i557.photobucket.com/albums/s...39911537_n.jpg

http://i557.photobucket.com/albums/s...34329759_n.jpg

http://i557.photobucket.com/albums/s...23589868_n.jpg

http://i557.photobucket.com/albums/s...66467781_n.jpg

http://i557.photobucket.com/albums/s...16270888_n.jpg


After the hood was straightened, I wanted to check the fit of the hood against the cab. I leveled the cab and used half of the rotisserie to hold the front of the hood.

http://i557.photobucket.com/albums/s...82030696_n.jpg

http://i557.photobucket.com/albums/s...48668238_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The left side of the hood line up great with the cowl, but the right side was bent out 1 7/16".

http://i557.photobucket.com/albums/s...25462454_n.jpg

http://i557.photobucket.com/albums/s...44335028_n.jpg


1 7/16" gap on the driver side.

http://i557.photobucket.com/albums/s...15647631_n.jpg


I cut three slices in the inner brace while it was on the truck, pulled the hood into shape, then tack welded the brace back together. This pulled the hood edge back into place against the cowl. The cuts were fully welded up and the weld beads smoothed down.

http://i557.photobucket.com/albums/s...56544790_n.jpg


After cutting and reshaping the brace, much better fit.

http://i557.photobucket.com/albums/s...06724844_n.jpg

http://i557.photobucket.com/albums/s...74724245_n.jpg


Left side still looks good after reshaping the right side.

http://i557.photobucket.com/albums/s...03714589_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The hood latches had surface rust so I bead blasted and painted them. Glass beads are great for latches since they are easy to get out of the latch mechanism- no gritty residue left over.

http://i557.photobucket.com/albums/s...60457719_n.jpg


Stamping L&R to keep them from getting mixed up after blasting. Marking them with a marker only works if the part isn't getting stripped and repainted.

http://i557.photobucket.com/albums/s...79427034_n.jpg


Bead blasted.

http://i557.photobucket.com/albums/s...21719391_n.jpg

http://i557.photobucket.com/albums/s...70617506_n.jpg


And painted.

http://i557.photobucket.com/albums/s...90771494_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The fenders were a nightmare!! The tops were fairly straight but everywhere else had major damage!


This is the passenger front fender, with a huge dent on the wheel opening lip. The lip was severely pushed back into the fender, creating a large bulge around the dent.

http://i557.photobucket.com/albums/s...52413693_n.jpg


Crumpled front lower area.

http://i557.photobucket.com/albums/s...11792117_n.jpg


Rear bottom area had been crease and halfway repaired.

http://i557.photobucket.com/albums/s...59951822_n.jpg


Large area of damage on the rear section.

http://i557.photobucket.com/albums/s...23979219_n.jpg


More dents on the front, and the wheel opening lip was cracked.

http://i557.photobucket.com/albums/s...10167381_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Fixing the large dent on the wheel opening lip.


Before.

http://i557.photobucket.com/albums/s...52413693_n.jpg


Beginning to work the metal back into shape. This shows just how much the metal had been pushed around.

http://i557.photobucket.com/albums/s...75790665_n.jpg


Shrinking, and hammer/dolly work to bring the raised area down.

http://i557.photobucket.com/albums/s...93142179_n.jpg

http://i557.photobucket.com/albums/s...17517033_n.jpg

http://i557.photobucket.com/albums/s...12969569_n.jpg


Checking the opening edge shape with a long, flexible ruler.

http://i557.photobucket.com/albums/s...49413816_n.jpg


After more shrinking and H/D work.

http://i557.photobucket.com/albums/s...77934851_n.jpg


Finished up, the ruler edge would lay down flat all along the opening.

http://i557.photobucket.com/albums/s...39621544_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The bottom edge was pushed in, and there was a fender brace bracket that was bent out of shape.

http://i557.photobucket.com/albums/s...11995310_n.jpg

http://i557.photobucket.com/albums/s...31067592_n.jpg


Bottom edge straightened, and the bracket area back in shape.

http://i557.photobucket.com/albums/s...86747070_n.jpg

http://i557.photobucket.com/albums/s...76174421_n.jpg


Heat shrinking with a torch to get the creased area back flat.

http://i557.photobucket.com/albums/s...98537200_n.jpg

http://i557.photobucket.com/albums/s...49979113_n.jpg

http://i557.photobucket.com/albums/s...00229535_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Forgot to mention that I did all of the repair work on the fenders with the front clip assembled to hold everything in shape. Fixing the fenders on a bench or stand would let them flex abnormally, and the repaired areas would have the wrong shapes/contours when bolted up.

http://i557.photobucket.com/albums/s...39760106_n.jpg


Front bottom edge was crumpled.

http://i557.photobucket.com/albums/s...30554349_n.jpg

http://i557.photobucket.com/albums/s...76903539_n.jpg


Gap between the fender and grill straightened out.

http://i557.photobucket.com/albums/s...81432472_n.jpg


Metalshaping finished.

http://i557.photobucket.com/albums/s...22317142_n.jpg


Inside bottom edge was chewed up pretty good. I opened it up to straighten the kinks out, then re-rolled it.

http://i557.photobucket.com/albums/s...95531244_n.jpg

http://i557.photobucket.com/albums/s...00113468_n.jpg

http://i557.photobucket.com/albums/s...54702899_n.jpg

http://i557.photobucket.com/albums/s...68325489_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Just found and read this thread from the beginning, amazing work. I have to echo what the others have said, it's great to see an oddball truck like this get saved! It's the unusual stuff at the shows that catches my eye.

Re: '55 International Metal/Body/Paint Work
 

Thanks plainred65, I'm glad the owner is saving it too!


The driver side fender wasn't anywhere near as bad as the passenger side. It had a spot of rust from moisture trapped between an inner brace, and around the front of the wheel opening lip had some damage.


Heat shinking the damaged area after roughing out the shape.

http://i557.photobucket.com/albums/s...18262086_n.jpg


After heatshrinking and sanding with a DA to smooth the surface, I blocked the damaged area to find the high/low spots.

http://i557.photobucket.com/albums/s...41419924_n.jpg


After a few rounds of hammer/dolly work and block sanding to pinpoint the high/low spots and work them flat.

http://i557.photobucket.com/albums/s...89965318_n.jpg


The front edge was bent where it bolted to the grill panel, so I straightened that out.

http://i557.photobucket.com/albums/s...48739650_n.jpg

http://i557.photobucket.com/albums/s...42158853_n.jpg


More damage around the wheel opening, it got the same heatshrink/block/hammer and dolly treatment.

http://i557.photobucket.com/albums/s...50628362_n.jpg


The upper edge of the fender lip was uneven, so I made relief cuts to straighten the edge.

http://i557.photobucket.com/albums/s...52363609_n.jpg

http://i557.photobucket.com/albums/s...28351859_n.jpg

http://i557.photobucket.com/albums/s...78449026_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Fixing the rust on the top of the fender required removing the inner brace that caused the rust to begin with. You can see where someone tried to fix the rust hole in the past by packing it with filler.

http://i557.photobucket.com/albums/s...66542457_n.jpg

http://i557.photobucket.com/albums/s...74134713_n.jpg


Inner brace removed. You can see just how much rust was hiding in there, and how much was dislodged just by removing it.

http://i557.photobucket.com/albums/s...10955993_n.jpg


http://i557.photobucket.com/albums/s...56980867_n.jpg

http://i557.photobucket.com/albums/s...72695685_n.jpg


Inner brace sandblasted.

http://i557.photobucket.com/albums/s...15843297_n.jpg


Making a new side for the inner brace.

http://i557.photobucket.com/albums/s...07199228_n.jpg


http://i557.photobucket.com/albums/s...73923596_n.jpg

http://i557.photobucket.com/albums/s...20397662_n.jpg


Rusted area of the sheetmetal cut out and new metal welded in. The area that was underneath the brace was sandblasted as well.

http://i557.photobucket.com/albums/s...48992653_n.jpg

http://i557.photobucket.com/albums/s...99350554_n.jpg

http://i557.photobucket.com/albums/s...08333058_n.jpg

http://i557.photobucket.com/albums/s...29776247_n.jpg


The backside of the brace and the fender were coated with etching primer before welding the brace back in. This will keep rust from forming under the brace again.

http://i557.photobucket.com/albums/s...55918914_n.jpg

Re: '55 International Metal/Body/Paint Work
 

With the metalwork out of the way, I skim coated the fenders and hood and blocked them straight. Then they got three coats of Slick Sand, and more blocking.

http://i557.photobucket.com/albums/s...75025462_n.jpg

http://i557.photobucket.com/albums/s...88112394_n.jpg


Sprayed with Slick Sand.

http://i557.photobucket.com/albums/s...63753759_n.jpg

http://i557.photobucket.com/albums/s...79636718_n.jpg


And blocked flat.

http://i557.photobucket.com/albums/s...28096607_n.jpg

http://i557.photobucket.com/albums/s...92974453_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Some details of blocking the Slick Sand. I block the primer down until I hit bare metal. This way the primer is as thin as possible and doesn't have to thick of a build to become unstable if the panel has any flexing- preventing cracks. You can see the different coats of primer being blocked off around the high spots.

http://i557.photobucket.com/albums/s...68168441_n.jpg


On body lines and details, I sand the flat section first, cutting into the body line with the edge of the block until I hit bare metal. This cuts the body line straight and keeps the primer build up in the line to a minimum.

http://i557.photobucket.com/albums/s...19744883_n.jpg


With the upper edge cut and leveled, it gets taped up so blocking the bottom half doesn't damage the upper part that's already straight.

http://i557.photobucket.com/albums/s...88505311_n.jpg


Both sides blocked, keeping the body lines straight and well defined. This will really make the paint stand out in these areas after cutting and buffing.

http://i557.photobucket.com/albums/s...27514466_n.jpg


Same treatment on the front edge of the raised stamping.

http://i557.photobucket.com/albums/s...95463294_n.jpg


Minor low spots are touched up with filler and blocked down. If the metalwork and skimcoat/blocking was done correctly, there are very few areas to rework after priming and blocking with Slick Sand.

http://i557.photobucket.com/albums/s...64945697_n.jpg


The flat areas of the fenders were blocked first, then a flexible sanding pad was used to sand the wheel opening lip, making sure to keep an even radius around the lip.

http://i557.photobucket.com/albums/s...47612520_n.jpg

http://i557.photobucket.com/albums/s...80872647_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Here's a shot of my sanding blocks. The white tube is PVC for blocking concave surfaces. The long/skinny Durablocks are great to cut down shorter for smaller areas.

http://i557.photobucket.com/albums/s...48731426_n.jpg

Re: '55 International Metal/Body/Paint Work
 

There were a couple of filler panels that mount to the fender bottoms that needed straightening.

http://i557.photobucket.com/albums/s...12654178_n.jpg

http://i557.photobucket.com/albums/s...75606176_n.jpg

http://i557.photobucket.com/albums/s...05982297_n.jpg


The cowl vent rain tray had what looked like hammer marks that needed to be shrunk and straightened. It has already been blasted but had rattle can primer on it that needed to be stripped. It was sandblasted before skimcoating and repriming.

http://i557.photobucket.com/albums/s...98166419_n.jpg

http://i557.photobucket.com/albums/s...43292214_n.jpg

http://i557.photobucket.com/albums/s...26145666_n.jpg

http://i557.photobucket.com/albums/s...66839854_n.jpg


The glovebox door was sandblasted and prepped for primer.

http://i557.photobucket.com/albums/s...09379582_n.jpg


Primed with Slick Sand and blocked flat, ready for tinted K93.

http://i557.photobucket.com/albums/s...01630558_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The windshield trim panels needed stripping repair. They were treated with PPG DX series Metal Cleaner and Metal Conditioner before being primed with DP90.

http://i557.photobucket.com/albums/s...76911297_n.jpg

http://i557.photobucket.com/albums/s...75869645_n.jpg

http://i557.photobucket.com/albums/s...38716596_n.jpg

http://i557.photobucket.com/albums/s...89381465_n.jpg


The dash panel needed stripping so I covered it with rags soaked in lacquer thinner, then covered that with tinfoil until the thinner softened the paint enough to scrape it off.

http://i557.photobucket.com/albums/s...11271010_n.jpg

http://i557.photobucket.com/albums/s...92148147_n.jpg

http://i557.photobucket.com/albums/s...09841381_n.jpg

http://i557.photobucket.com/albums/s...20588831_n.jpg


After scraping off the majority of the old paint, I sandblasted the dash panel. I didn't want to just blast the paint off and take a chance of warping the metal since it was thin and didn't have any shape to strengthen it.

http://i557.photobucket.com/albums/s...04056126_n.jpg


Treated with PPG Metal Cleaner/Conditioner.

http://i557.photobucket.com/albums/s...48920582_n.jpg


Primed with DP90

http://i557.photobucket.com/albums/s...98666291_n.jpg


And three coats of tinted K36.

http://i557.photobucket.com/albums/s...19515329_n.jpg

Re: '55 International Metal/Body/Paint Work
 

The hinges were primed with DP90, then scuffed and shot with Slick Sand the next day.

http://i557.photobucket.com/albums/s...55753099_n.jpg


After block sanding, ready for K36.

http://i557.photobucket.com/albums/s...97213889_n.jpg


The floor/firewall panel was blasted, primed with DP90, and seam sealed before being sprayed with three coats of homemade Lizard Skin type sound deadener/heat insulation.

http://i557.photobucket.com/albums/s...73087816_n.jpg

http://i557.photobucket.com/albums/s...20233061_n.jpg

http://i557.photobucket.com/albums/s...09874475_n.jpg

http://i557.photobucket.com/albums/s...41013486_n.jpg


Dash panel sprayed with Slick Sand and block sanded.

http://i557.photobucket.com/albums/s...90036037_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Amazing work, John. Most people don't have a clue at the effort and time that it takes to get a body to that level. That International looks especially daunting because you don't have the luxury of a separate, floating grill or chrome pieces that you can hide mismatches underneath. That whole front group is out in the open, with miles of panel gaps to address.

A Master at work...............love this thread!

Re: '55 International Metal/Body/Paint Work
 

It is all looking REAAALLLY good, astro. You have some valuable tips in here for us too that will be useful to many of us in the future. Did you get the homemade lizardskin the way that you wanted it eventually? Also what gun are you shooting the Slick Sand through?
Hmmm you are 920 miles from here, you want another job? Haha

Re: '55 International Metal/Body/Paint Work
 

That's really looking great, John. Are you going to have it done before the snow starts to fly?

Re: '55 International Metal/Body/Paint Work
 

Thanks Alex, you're exactly right about most people not knowing what goes into it! They hear "10k" or "20k" paint job and it blows their minds, but to do it right from the ground up it really does take that much labor to get one painted these days. The gaps were surprisingly good on the truck, apart from the doors and the back edge of the hood. The rest of the gaps/alignment on the front clip was very acceptable.


Thanks alot El Campo! The stuff I mixed up and posted in the body/paint section (http://67-72chevytrucks.com/vboard/s...d.php?t=511370) is working great; it works for sound dampening but I think with the ceramic air beads it's more suited for use as heat insulation. I still want to try mixing the beads in with Kool Seal since it's a softer coating and should dampen noise better. Lizard Skin makes two different coatings, one for heat and one for sound, so I'm guessing that I'm not too far off from what they're making. I'm using a Sata KLC RP with a 2.5 tip, and thinning the SS 10% with fast urethane reducer. It lays out pretty smooth that way, though not as smooth as urethane high build. What you got to bring over?!


I'm hoping to, though it rarely snows here so that gives me a bit more time... :lol: I'm not good at setting and making deadlines; they always run over. I've still got to spray/cut/buff the front clip but it's all ready to spray, just waiting on a dry day to paint them. The cab (already picked up) and doors are done and ready to be bolted up. I still have the whole bed and rear fenders to do though, and I'll probably be making bedsides and the header panel from scratch.

Re: '55 International Metal/Body/Paint Work
 

Astronaut, could you give a quick explanation of how you heat shrink metal? Is it a hard technique to learn? Seems like it would handy as around a dent you always have stretched metal. Following this (and all your threads) closely!

Re: '55 International Metal/Body/Paint Work
 

It's not hard if you learn to do it the right way- I wasn't taught the right way, so I was frustrated with it at first. I tried shrinking with a torch and wet rag like some people tell you to do, but they leave out the step of using the hammer and dolly to actually flatten and pull the metal inward while the metal is still red hot. That works but has very little shrinking action, and it's easy to warp the metal more than you're actually helping. Or atleast that was my experience.

The way I now do it is: Quickly (or else you'll warp a bigger spot from the panel getting too hot) get a spot about the size of a quarter red hot, support the back with a dolly, and hammer around the red spot to draw down the high spot, then you quench the spot with a wet rag. Don't hit any of the red hot area with the hammer, or you'll just add to the amount of stretch. Repeat until the area is flat and isn't popping in and out. If you over shrink you can use the "hammer on dolly" method to stretch the metal. Hitting the hammer directly on the dolly squeezes the metal outwards to stretch it.

Re: '55 International Metal/Body/Paint Work
 

Here were the front clip panel gaps. I was surprised at how well everything fit without any tweaking.



http://i557.photobucket.com/albums/s...69817343_n.jpg

http://i557.photobucket.com/albums/s...25478117_n.jpg

http://i557.photobucket.com/albums/s...72524811_n.jpg

http://i557.photobucket.com/albums/s...02295016_n.jpg

http://i557.photobucket.com/albums/s...30660141_n.jpg

http://i557.photobucket.com/albums/s...41529246_n.jpg

http://i557.photobucket.com/albums/s...67947845_n.jpg

http://i557.photobucket.com/albums/s...42158853_n.jpg

Re: '55 International Metal/Body/Paint Work
 

Looking beautiful as usual. My project that I would literally seriously consider having you work on is the truck in my signature. Long story short but it is sheet metal work only that I need done. The chassis has all been rebuilt. The sheet metal consists of the following: Original paint cab from Arizona, no rust through anywhere, rockers are perfect even, New bedsides (SWB), bed has been assembled but one of the bedsides has a wave in it in front of the front wheel and there are several dents on them, original tailgate (no rust), original hood no rust and straight (off of the same truck as cab came from), one original paint door (no rust and one small dent on the bottom of it) and one aftermarket door that actually fits well, one original paint front fender (minimal rust, nowhere close to rusting through) and one aftermarket fender that also fits well, aftermarket core support and two aftermarket inner fenders. No rust repair anywhere :) I am keeping eye out for another original paint door as I REALLLLY like OEM parts versus taiwan crap. The doors I want the handles and mirrors shaved, I will have installed (or mocked up I should say) the one piece windows and the door poppers. I have had such poor luck and gotten screwed by collision body shops that are not passionate about their work and do crappy work with the lower quality products that I would rather take this 1000 miles away and get done by someone who has shown amazing potential than go through that BS again! Especially since you are a forum member and I could splash these pages with your work :) Oh yea and the final color is going to be the new Range Rover white. Not trying to take away from this International or your thread! I am anxious for those final paint pictures, I could have sworn I saw some teasers somewhere on here of some liquid looking red paint that was about 10 miles deep.

Re: '55 International Metal/Body/Paint Work
 

Say what? Can you provide a link to Webster's or Wikipedia with an explanation of that term? I'm having a hard time comprehending that one... :lol:

I'd' be up for doing it, but I've got the whole bed to start/finish (likely that I'll be building from scratch) on the '55, and '58 ragtop VW already lined up for metal/body/paintwork. After that I've got a guy that wants me to take the front clip off a couple of his Chevelle's and detail everything under the hood. I've only got room for one at a time, so it'll be quite awhile before I could take on anything else. I'd love to do it though- I'd like to get into doing metalwork only anyways. The body/paint process just takes too long.


Here's a few more teaser shots. The first is the reflection of the doors in the roof skin, and the reflection on the doors is a building about 50 feet away.

http://i557.photobucket.com/albums/s...19018215_n.jpg

http://i557.photobucket.com/albums/s...60974188_n.jpg

http://i557.photobucket.com/albums/s...66597347_n.jpg