I need help on my 67 c10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

captainron67 · 02-27-2006, 01:17 AM

I just bought a 67 c10 small window original truck with a six cylinder. Anyways 6000 later and a 383 stroker I need to know if there is a different clutch linkage set up cause i cant get this one to fit with the headers. Any pics would be great or info.

davidh · 02-27-2006, 02:17 AM

running a 3speed? Maybe you should get some shorty headers. Then it will clear.

MDC · 02-27-2006, 02:22 AM

The headers are most likely the problem. Different brands will fit differently. Like davidh says, shorty's are probably best. I have that on my list to do also. The PO just hammered the back tube until it cleared.
BTW Welcome from N Texas

**special-K** · 02-27-2006, 10:20 AM

Do the headers run into the linkage tube itself,or one of the two arms(tabs)that are on it?I have relocated one before.Clean all the grease out,cut it off and reweld out of the way.

**1970 CST Short Wide** · 02-27-2006, 10:29 AM

Are you trying to run the 6 cyl clutch linkage? Its differante for a 6 to a V8

captainron67 · 02-27-2006, 06:21 PM

Yes im running long tube headers and a 3 speed(runs like a sewing machine, but wicked at high rpms). My problem I think i need to jack the motor up on the drivers side then put the z bar in. I dont even no if the linkage hits the header yet. Also I noticed that my engine mounts are on the rear two holes while my buddies auto runs in the front two hole. Is that supposed to be different on auto vs. manuel?

davidh · 02-27-2006, 08:35 PM

front holes are 8cyl and 6cyl are rear.

71chevytruckguy · 02-27-2006, 10:46 PM

when the motor's in the front 2 holes, flowtech headers will clear. what i have on my '69. got them at autozone for $85.

captainron67 · 03-03-2006, 03:16 AM

Thanks for info I just cut the arm off the linkage and re welded it on in right position.Works great.

02-27-2006, 01:17 AM	#1
captainron67 Registered User Join Date: Feb 2006 Location: Marysville Washington Posts: 13	I need help on my 67 c10 I just bought a 67 c10 small window original truck with a six cylinder. Anyways 6000 later and a 383 stroker I need to know if there is a different clutch linkage set up cause i cant get this one to fit with the headers. Any pics would be great or info.

02-27-2006, 02:17 AM	#2
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,221	Re: I need help on my 67 c10 running a 3speed? Maybe you should get some shorty headers. Then it will clear.

02-27-2006, 02:22 AM	#3
MDC Registered User Join Date: Oct 2005 Location: N Texas Posts: 727	Re: I need help on my 67 c10 The headers are most likely the problem. Different brands will fit differently. Like davidh says, shorty's are probably best. I have that on my list to do also. The PO just hammered the back tube until it cleared. BTW Welcome from N Texas __________________ 67 C10 Shortbed 327 05 F150 4x4 NO APPOLOGIES 's 02 Xpress X19 02 Yamaha VMax 150 www.xpressboats.com Nothing says 'poor craftmanship' like wrinkles in your duct tape

02-27-2006, 10:20 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: I need help on my 67 c10 Do the headers run into the linkage tube itself,or one of the two arms(tabs)that are on it?I have relocated one before.Clean all the grease out,cut it off and reweld out of the way. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

02-27-2006, 10:29 AM	#5
1970 CST Short Wide Senior Moment Join Date: Mar 2002 Location: Pittsburg Ca Posts: 4,078	Re: I need help on my 67 c10 Are you trying to run the 6 cyl clutch linkage? Its differante for a 6 to a V8 __________________ 1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565

02-27-2006, 06:21 PM	#6
captainron67 Registered User Join Date: Feb 2006 Location: Marysville Washington Posts: 13	Re: I need help on my 67 c10 Yes im running long tube headers and a 3 speed(runs like a sewing machine, but wicked at high rpms). My problem I think i need to jack the motor up on the drivers side then put the z bar in. I dont even no if the linkage hits the header yet. Also I noticed that my engine mounts are on the rear two holes while my buddies auto runs in the front two hole. Is that supposed to be different on auto vs. manuel?

02-27-2006, 08:35 PM	#7
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,221	Re: I need help on my 67 c10 front holes are 8cyl and 6cyl are rear.

02-27-2006, 10:46 PM	#8
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: I need help on my 67 c10 when the motor's in the front 2 holes, flowtech headers will clear. what i have on my '69. got them at autozone for $85. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

03-03-2006, 03:16 AM	#9
captainron67 Registered User Join Date: Feb 2006 Location: Marysville Washington Posts: 13	Re: I need help on my 67 c10 Thanks for info I just cut the arm off the linkage and re welded it on in right position.Works great.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.