project- no name - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*mrhino* · 12-20-2009, 08:07 PM

Just start a new project last week, found a guy on craigslist selling a 70 shortbed, said body was ruff. boy he wasn't kidding cab and bed were complete junk nothing on it was any good except VIN plate and title. so i bought it anyway, and hauled it home. and was going to work on the chassis and find body parts here and there to complete it. the very next day im on craigslist again and find a guy on the other side of the state selling a rust free cab, bed hood, fenders, doors, core support, and bunch of other parts one would need all from out west he bought 8 years ago for his project that never went anywhere. it is a long bed but before i scraped the old bondo infested short bed i practiced cutting 8" out of it. so i feel confident i could cut the longbed and make it a shortbed.
Iv just got the frame stripped of it cross members and and trailing arms, I had nate from porterbuilt street rods build me some trailing arms and xmember, should be here in a few days. tomorrow i will get it ready to go to sandblasting.

292farmer · 12-20-2009, 08:17 PM

welcome! what are your plans besides putting it together

u going with a low rider or stock look?

*mrhino* · 12-20-2009, 08:30 PM

im going to lower it. 4 wheel disc, I just bought boss 338 wheels (18's) hopefully find a nice 5.3l or 6.0 to put in it.

*mrhino* · 12-20-2009, 08:35 PM

pic

brossow · 02-25-2010, 10:11 PM

I'm subscribing to this build thread hoping that you'll post more pics soon! Saw your pics (including the one below) in the Boss 338 thread and have some questions. Specifically, I'm wondering what you're using for motor mounts and tranny crossmember because it looks like you're having the same issue with engine angle as I am -- seemingly tipped back too far and I'm wondering what, if anything, you have in mind to correct the angle. (Not criticizing, just observing.)

Whatever the case, great project and FAST progress in just a couple months!

Brent

*mrhino* · 02-28-2010, 11:50 AM

To tell the truth I havnt given the angle much thought, (Yet) if i was useing a carb engine i might be a little more critical of it. im using cpp tubular mounts and their tubular crossmember. the angle is 7 degrees and it looks like a small spacer under the trans mount would take care of most of it if not all of it. I check a 02 silverado which is the same as the donor truck and it measued 3 degrees.

brossow · 02-28-2010, 12:01 PM

I was originally using the CPP tubular mounts but switched to the ECC Gen3 kit when I was trying to figure out header clearance issues and it looked like the CPP mounts were going to interefere. I'm also using the CPP tranny crossmember and think that the mounting tab should have been welded to the top rather than the bottom. I'm also looking at having to fabricate a spacer, and I've seen several other people with the same issue, which makes me wonder how that particular design made it to market.

Like you, I'm not worried about carb angle, but I am very concerned about getting the driveline geometry right. I don't want my tranny tipped down at 7° and the rear end up at 3°. I'm torn between fabbing a spacer and just getting a different crossmember from somewhere else (which I know may have the same problem).

*mrhino* · 02-28-2010, 06:05 PM

here are some pictures of the build. me and some buddies put the cab on friday and now my back is killing me, so im gonna take few days off from working on it. i want it done by the end of april. better not slack off to much.

started coating it on Dec. 31 using KBS coating

*mrhino* · 02-28-2010, 06:09 PM

coating pics

*mrhino* · 02-28-2010, 06:32 PM

pics 2

*mrhino* · 02-28-2010, 06:45 PM

factory 5.3l engine wire harness, removed all unnecessary wires and pinouts thanks to the LT1 swap web site. not as bad as it looks. can you believe the kids had no desire to play pool until i put that **** all over it.

*mrhino* · 02-28-2010, 06:50 PM

pics 4

*mrhino* · 02-28-2010, 07:04 PM

at this point i cant even hardly walk through my garage

*mrhino* · 02-28-2010, 07:12 PM

Big Thank you goes out to Nathan at porter built xmember and arms worked beautifully

MONTE · 02-28-2010, 07:14 PM

Looks nice, keep it going.

*mrhino* · 02-28-2010, 07:20 PM

02 5.3l. put the boy to work. it wasn't dirty enough for him, he wanted to get greasy. he hasn't been out to help since.

VA72C10 · 02-28-2010, 07:20 PM

very nice.....

*mrhino* · 02-28-2010, 07:32 PM

I did get my baby girl to come out and turn a few wrenches.

*mrhino* · 02-28-2010, 07:42 PM

this is what she looks like as of 2/28/10 i have 2 months to go

Ronm909 · 02-28-2010, 07:46 PM

subscribed.. nice project

heymoe · 02-28-2010, 08:01 PM

Looking Good! The frame pics look just like mine. http://67-72chevytrucks.com/vboard/s...d.php?t=371235

What type of fuel hose did you use? Also I am looking for info on brake lines. Did you use the coiled type or straight tubing?

*mrhino* · 02-28-2010, 09:06 PM

Thanks guys! your right heymoe, they do look alike, I used -6 push lok hose, I added the cost of going all diffrent ways, steel braided, hard line and a combonation of all three and it turned out the push lok from front to back was the cheapest. brake lines were straight pieces that i bent and flared.

brossow · 02-28-2010, 09:49 PM

What are you using for headers?

*mrhino* · 03-01-2010, 07:44 AM

The headers are sanderson's. they came with the engine. I got the engine from a guy who was building a s10 but ran out of money. I figured thats what they were suppose to fit, but they fit great in a c10. with plenty of room and should be no interference problems, but i don't have the exhaust run yet.

brossow · 03-01-2010, 09:21 AM

Can you tell me more about your tranny cooler lines? I see you've got them running off to the side and back.

12-20-2009, 08:07 PM	#1
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	project- no name Just start a new project last week, found a guy on craigslist selling a 70 shortbed, said body was ruff. boy he wasn't kidding cab and bed were complete junk nothing on it was any good except VIN plate and title. so i bought it anyway, and hauled it home. and was going to work on the chassis and find body parts here and there to complete it. the very next day im on craigslist again and find a guy on the other side of the state selling a rust free cab, bed hood, fenders, doors, core support, and bunch of other parts one would need all from out west he bought 8 years ago for his project that never went anywhere. it is a long bed but before i scraped the old bondo infested short bed i practiced cutting 8" out of it. so i feel confident i could cut the longbed and make it a shortbed. Iv just got the frame stripped of it cross members and and trailing arms, I had nate from porterbuilt street rods build me some trailing arms and xmember, should be here in a few days. tomorrow i will get it ready to go to sandblasting. Attached Images

12-20-2009, 08:17 PM	#2
292farmer Registered User Join Date: Nov 2009 Location: stoddard nh Posts: 693	Re: project- no name welcome! what are your plans besides putting it together u going with a low rider or stock look?

12-20-2009, 08:30 PM	#3
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name im going to lower it. 4 wheel disc, I just bought boss 338 wheels (18's) hopefully find a nice 5.3l or 6.0 to put in it. Last edited by mrhino; 12-20-2009 at 08:33 PM. Reason: add

12-20-2009, 08:35 PM	#4
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name pic Attached Images

02-25-2010, 10:11 PM	#5
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: project- no name I'm subscribing to this build thread hoping that you'll post more pics soon! Saw your pics (including the one below) in the Boss 338 thread and have some questions. Specifically, I'm wondering what you're using for motor mounts and tranny crossmember because it looks like you're having the same issue with engine angle as I am -- seemingly tipped back too far and I'm wondering what, if anything, you have in mind to correct the angle. (Not criticizing, just observing.) Whatever the case, great project and FAST progress in just a couple months! Brent __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...) Last edited by brossow; 02-28-2010 at 12:02 PM. Reason: typo

02-28-2010, 11:50 AM	#6
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name To tell the truth I havnt given the angle much thought, (Yet) if i was useing a carb engine i might be a little more critical of it. im using cpp tubular mounts and their tubular crossmember. the angle is 7 degrees and it looks like a small spacer under the trans mount would take care of most of it if not all of it. I check a 02 silverado which is the same as the donor truck and it measued 3 degrees.

02-28-2010, 12:01 PM	#7
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: project- no name I was originally using the CPP tubular mounts but switched to the ECC Gen3 kit when I was trying to figure out header clearance issues and it looked like the CPP mounts were going to interefere. I'm also using the CPP tranny crossmember and think that the mounting tab should have been welded to the top rather than the bottom. I'm also looking at having to fabricate a spacer, and I've seen several other people with the same issue, which makes me wonder how that particular design made it to market. Like you, I'm not worried about carb angle, but I am very concerned about getting the driveline geometry right. I don't want my tranny tipped down at 7° and the rear end up at 3°. I'm torn between fabbing a spacer and just getting a different crossmember from somewhere else (which I know may have the same problem). __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...)

02-28-2010, 06:05 PM	#8
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name here are some pictures of the build. me and some buddies put the cab on friday and now my back is killing me, so im gonna take few days off from working on it. i want it done by the end of april. better not slack off to much. started coating it on Dec. 31 using KBS coating

02-28-2010, 06:09 PM	#9
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name coating pics Attached Images

02-28-2010, 06:32 PM	#10
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name pics 2 Attached Images

02-28-2010, 06:45 PM	#11
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name factory 5.3l engine wire harness, removed all unnecessary wires and pinouts thanks to the LT1 swap web site. not as bad as it looks. can you believe the kids had no desire to play pool until i put that **** all over it. Attached Images

02-28-2010, 06:50 PM	#12
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name pics 4 Attached Images

02-28-2010, 07:04 PM	#13
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name at this point i cant even hardly walk through my garage Attached Images

02-28-2010, 07:12 PM	#14
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name Big Thank you goes out to Nathan at porter built xmember and arms worked beautifully Attached Images

02-28-2010, 07:14 PM	#15
MONTE Registered User Join Date: Oct 2005 Location: Donna, Texas Posts: 286	Re: project- no name Looks nice, keep it going.



Register or Log In To remove these advertisements.

02-28-2010, 07:20 PM	#16
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name 02 5.3l. put the boy to work. it wasn't dirty enough for him, he wanted to get greasy. he hasn't been out to help since. Attached Images

02-28-2010, 07:20 PM	#17
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: project- no name very nice..... __________________ Looking for a 67-72 swb or blazer project in or around VA.

02-28-2010, 07:32 PM	#18
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name I did get my baby girl to come out and turn a few wrenches. Attached Images

02-28-2010, 07:42 PM	#19
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name this is what she looks like as of 2/28/10 i have 2 months to go Attached Images

02-28-2010, 07:46 PM	#20
Ronm909 67GMC Slammed Join Date: Feb 2009 Location: Rancho Cucamonga, Ca Posts: 255	Re: project- no name subscribed.. nice project __________________ my dropmembered 67 GMC build thread http://67-72chevytrucks.com/vboard/s...d.php?t=383215

02-28-2010, 08:01 PM	#21
heymoe Registered User Join Date: Mar 2009 Location: Lebanon, Ohio Posts: 324	Re: project- no name Looking Good! The frame pics look just like mine. http://67-72chevytrucks.com/vboard/s...d.php?t=371235 What type of fuel hose did you use? Also I am looking for info on brake lines. Did you use the coiled type or straight tubing?

02-28-2010, 09:06 PM	#22
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name Thanks guys! your right heymoe, they do look alike, I used -6 push lok hose, I added the cost of going all diffrent ways, steel braided, hard line and a combonation of all three and it turned out the push lok from front to back was the cheapest. brake lines were straight pieces that i bent and flared.

02-28-2010, 09:49 PM	#23
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: project- no name What are you using for headers? __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...)

03-01-2010, 07:44 AM	#24
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: project- no name The headers are sanderson's. they came with the engine. I got the engine from a guy who was building a s10 but ran out of money. I figured thats what they were suppose to fit, but they fit great in a c10. with plenty of room and should be no interference problems, but i don't have the exhaust run yet.

03-01-2010, 09:21 AM	#25
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: project- no name Can you tell me more about your tranny cooler lines? I see you've got them running off to the side and back. __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...)

Register or Log In To remove these advertisements.