Aluminum intakes for sale. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**crossy** · 07-03-2003, 03:30 AM

ALL manifolds listed are Aluminum and used . All are Dual plane design, I do not sell junk. Even if I heli-coil something I guarantee that it is done right . I can take a GOOD pic of any of these..all small block ones are for PRE-1987 heads. Prices DO NOT include shipping. the small block intakes weight about 20 Lbs. properly boxed and I am in N.J. @ 08070 zip. I can figure shipping with your zip code. I accept paypal if you add 3% to price. Also accept money orders. PLEASE EMAIL ME PERSONALLY at all4trux@snip.net and be specific in the subject box. thanx, DAVE
1.)= $140 ,SBC, Edelbrock Performer #2101 , Finish is Jethot coated inside & out. on a 1-10 scale the jethot is still an 8, very clean , No pitting, If it gets tarnished looking it shines back up with 'neverdull '. Jethot is impervious to antifreeze corrosion attack. this manifold will look good for a long time. I want less than it cost just to get it coated.
2.)=$69, SBC, Holley Contender #300-38, Finish is sandblasted clean,clear coated.comparable to Edelbrock performer, I think this is better for trucks with stock engine. has ridges in floor to break up fuel puddling. No pitting from corrosion. heater hose nipple included.
3.)= SOLD!$55, SBC Edelbrock performer, #2101, Finish is used dirty, not greasy.I can blast it for $10 more. This one was left alone for someone here on the forum that wanted it cheap 'as is' and he never paid up.
has hose nipple, no pitting.SOLD!
4.)= $99,SBC, Edelbrock Performer EGR #3701 ,Finish is bead blasted and clear coated, new condition. this is for the guys that want an aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. hose nipple installed.
5.)=$99,SBC, ZZ4 GM bowtie #10185063 EGR ,about equal to a performer RPM in design but has EGR hole. ,Finish is factory and then was wire wheeled for a little shine. I can sandblast it for $10 extra. , new condition. this is for the guys that want a performence aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection.
6.)=$79,SBC,Weiand Stealth #8016, Finish is bead blasted then clear coated. Holley square flange, This manifold is equal to a Performer RPM, No pitting.
7.)=SOLD!$99,SBC, Offenhauser Dual port 360 #6008, Finish is bead blasted and clear coated,Very expensive new.these manifolds are ugly in my word but my choice for a daily hauler. Excellent all RPM manifold that has great bottom end torque because of a patented design.very minor pitting. This old school manifold has the provision for oil tube hole in the front for older engines. SOLD!
8.)=$99 , SBC, Edelbrock C4B , finish is clean but sprayed with Aluminum paint ??. I can sandblast this for $10 extra. This old school manifold has the provision for oil tube hole in the front for older engines. This was pretty much Edelbrocks original Mid to upper rpm street manifold that is designed like the old original Z28 intake.Has Holley square flange bolt pattern. very minor pitting,great shape for a 30 year old intake.These were great then and still are now.
9.)=$115 , Big Block Chevy BBC, Edelbrock performer 2-0 for oval port heads. Finish is bead blasted and clear coated. No pitting,

**crossy** · 07-08-2003, 09:23 AM

Zoomy, thanx for the interest. #3 is still available. I mainly replied here to give guys ideas of shipping. this one to 53932 would be $14 by UPS. thanx , DAVE

AirMale · 07-09-2003, 07:57 PM

This guy needs to put a YOU PULL-IT sign at his house, he's got it all!

**crossy** · 07-10-2003, 11:29 AM

#3 manifold has been sold.

Jay, the parts are already pulled - just bring cash!

What i really need is a DRAG/DRIVE-IT away for all the uncompleted projects and cars i no longer want. again, bring cash.

DAVE

**crossy** · 07-21-2003, 07:59 AM

top left =#4 , block off plate is not installed in the pic and it has a square flange adapter installed in this pic. but it is #4.

bottom left= #7 SOLD!

top right= #5

bottom right=#6

**crossy** · 08-05-2003, 10:25 PM

#3 & #7 SOLD!

07-03-2003, 03:30 AM	#1
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	Aluminum intakes for sale. ALL manifolds listed are Aluminum and used . All are Dual plane design, I do not sell junk. Even if I heli-coil something I guarantee that it is done right . I can take a GOOD pic of any of these..all small block ones are for PRE-1987 heads. Prices DO NOT include shipping. the small block intakes weight about 20 Lbs. properly boxed and I am in N.J. @ 08070 zip. I can figure shipping with your zip code. I accept paypal if you add 3% to price. Also accept money orders. PLEASE EMAIL ME PERSONALLY at all4trux@snip.net and be specific in the subject box. thanx, DAVE 1.)= $140 ,SBC, Edelbrock Performer #2101 , Finish is Jethot coated inside & out. on a 1-10 scale the jethot is still an 8, very clean , No pitting, If it gets tarnished looking it shines back up with 'neverdull '. Jethot is impervious to antifreeze corrosion attack. this manifold will look good for a long time. I want less than it cost just to get it coated. 2.)=$69, SBC, Holley Contender #300-38, Finish is sandblasted clean,clear coated.comparable to Edelbrock performer, I think this is better for trucks with stock engine. has ridges in floor to break up fuel puddling. No pitting from corrosion. heater hose nipple included. 3.)= SOLD!$55, SBC Edelbrock performer, #2101, Finish is used dirty, not greasy.I can blast it for $10 more. This one was left alone for someone here on the forum that wanted it cheap 'as is' and he never paid up. has hose nipple, no pitting.SOLD! 4.)= $99,SBC, Edelbrock Performer EGR #3701 ,Finish is bead blasted and clear coated, new condition. this is for the guys that want an aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. hose nipple installed. 5.)=$99,SBC, ZZ4 GM bowtie #10185063 EGR ,about equal to a performer RPM in design but has EGR hole. ,Finish is factory and then was wire wheeled for a little shine. I can sandblast it for $10 extra. , new condition. this is for the guys that want a performence aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. 6.)=$79,SBC,Weiand Stealth #8016, Finish is bead blasted then clear coated. Holley square flange, This manifold is equal to a Performer RPM, No pitting. 7.)=SOLD!$99,SBC, Offenhauser Dual port 360 #6008, Finish is bead blasted and clear coated,Very expensive new.these manifolds are ugly in my word but my choice for a daily hauler. Excellent all RPM manifold that has great bottom end torque because of a patented design.very minor pitting. This old school manifold has the provision for oil tube hole in the front for older engines. SOLD! 8.)=$99 , SBC, Edelbrock C4B , finish is clean but sprayed with Aluminum paint ??. I can sandblast this for $10 extra. This old school manifold has the provision for oil tube hole in the front for older engines. This was pretty much Edelbrocks original Mid to upper rpm street manifold that is designed like the old original Z28 intake.Has Holley square flange bolt pattern. very minor pitting,great shape for a 30 year old intake.These were great then and still are now. 9.)=$115 , Big Block Chevy BBC, Edelbrock performer 2-0 for oval port heads. Finish is bead blasted and clear coated. No pitting, __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks. Last edited by crossy; 08-05-2003 at 10:22 PM.

07-08-2003, 09:23 AM	#2
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	Zoomy, thanx for the interest. #3 is still available. I mainly replied here to give guys ideas of shipping. this one to 53932 would be $14 by UPS. thanx , DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-09-2003, 07:57 PM	#3
AirMale Senior Member Join Date: Jan 2003 Location: Atlantic City, NJ Posts: 1,073	This guy needs to put a YOU PULL-IT sign at his house, he's got it all! __________________ 86 SWB 9.0 LITER T-400-OD 4.11 eaton-4/5 drop Best 1/4 12.51 @112mph no traction

07-10-2003, 11:29 AM	#4
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	#3 manifold has been sold. Jay, the parts are already pulled - just bring cash! What i really need is a DRAG/DRIVE-IT away for all the uncompleted projects and cars i no longer want. again, bring cash. DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-21-2003, 07:59 AM	#5
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	top left =#4 , block off plate is not installed in the pic and it has a square flange adapter installed in this pic. but it is #4. bottom left= #7 SOLD! top right= #5 bottom right=#6 __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks. Last edited by crossy; 08-05-2003 at 10:24 PM.

08-05-2003, 10:25 PM	#6
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	#3 & #7 SOLD! __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.