TN 65-66 K20 4x4 chassis or project

[1968vetL-71]

Hey all,
I'm still looking for a complete 65 or 66 K20 4x4 chassis or rusty project truck. I'm just wanting the original frame, axles, trans/tcase. If there is an original motor thats fine. I do not want a complete daily driver or anything nice. I won't be using the body just the drivetrain and chassis.

Please let me know if you have or know of something.

Thanks again!!

[60-66]

Did you see this one ?

http://denver.craigslist.org/cto/5485367683.html

[1968vetL-71]

Its a tad more than what i want to spend on the stuff i need. The body on the truck adds more value than i would pay.
I found exactly what I'm looking for in wyoming on craiglist for 800 but by the time i called someone already snagged the trans and t-case.
I have time to be a little patient.

Thanks for the lead! very much appreciated.

[DPowers]

Dont know anything about this one:
https://asheville.craigslist.org/cto/5542607907.html

[Brad54]

Are you only wanting the trans and T-case?
I may have one for sale soon. 3spd manual and factory T-case from my '62.
Stock rear axle assembly too, if you need that.

-Brad

[1968vetL-71]

Brad, Thank you for the inquiry. I've gathered a couple trans/tcases already so right now i'm mainly looking for a rollin chassis or complete truck with a junk body on it. Im just gonna hold out for a 65 or 66. I appreciate the info tho. Good luck.

[Brad54]

Originally Posted by 1968vetL-71

Brad, Thank you for the inquiry. I've gathered a couple trans/tcases already so right now i'm mainly looking for a rollin chassis or complete truck with a junk body on it. Im just gonna hold out for a 65 or 66. I appreciate the info tho. Good luck.

I did pretty much the same thing: I bought a '62 K10 for the chassis. (Gotta have that wrap-around windshield and knee-knocker cab!) The body is nothing but dents and rust, held together by holes.
My son saw the body, and said "well... the dash is good, I guess."

I've got everything but a good cab for it already.
Gonna keep the front axle and springs, 90-percent sure I'm going with an NP205 transfer case and will run a 4spd OD manual trans. I've also got a line on a GMC Dana 44 rear end. Nothing on it is really hard-core as far as 4x4 trucks go, but I'm going to use it for construction sites and getting back into some hunting and fishing areas, and maybe light off-roading.

-Brad

[b.sharp]

I have what you are looking for but in a 64 factory k20. It has the original drivetrain with a jasper 292. The cab and doghouse are junk but matching vin plate. It has been sitting a long time but drivetrain is complete. I would take $1500 for it. I was going to put my 65 Dually on it but have changed my mind. I don't have any pictures on my iPad but can send you some to an email address tomorrow. If you are interested. The truck is near Frankfort, KY.

[b.sharp]

http://67-72chevytrucks.com/vboard/a...1&d=1391781746

Here is a picture I posted on the board of my K20 project.

[1968vetL-71]

From the pic the front end looks too be newer?
If you can send me pics i'll see if its what i'm wanting. I'll pm ya my addy

Thanks

[BLK65K10]

I have a 64 3/4 ton chassis that I will let go It is all original except has warn hubs. It is set up with V8 motor mounts. Send me a pm with email and I will see about getting some photos this weekend if you are interested. Thanks Lyle

[BLK65K10]

Here are some photos. I will send you a pm with details and number.
Thanks Lyle

[BLK65K10]

[BLK65K10]

[1968vetL-71]

Thanks for the pics Lyle. I"ll call ya per your PM. Thanks again.