Re: Need some engine advice and suggestions...
That fuel pump P/N doesn't show up, do you mean 11101?
Everything else looks good. I would recommend SS covered teflon hose. I had a problem with the SS rubber hoses pushing/outleaking fumes/vapor and my garage stunk from fuel. What size fitting do you have out of the tank? Do you have a return fitting? |
Re: Need some engine advice and suggestions...
Quote:
r/ |
Re: Need some engine advice and suggestions...
Looks like you are taking the right advice hartrod. It is going to be a fun ride when you are done with it.
|
Re: Need some engine advice and suggestions...
Quote:
|
Re: Need some engine advice and suggestions...
great build! i love those blow thru vortech and prochargers. that thing will be a beast
|
Re: Need some engine advice and suggestions...
Quote:
Quote:
Quote:
PCV - B transmission - A (ported?) Blowoff valve - B? MSD BTM - B? Boost/Vacuum gauge - A FPR signal - A (according to Aeromotive tech) Thoughts or suggestions? |
Re: Need some engine advice and suggestions...
Quote:
boost gauge-B to see what is actually inside engine everything else looks good. |
Re: Need some engine advice and suggestions...
1 Attachment(s)
Look what I found on my porch.
|
Re: Need some engine advice and suggestions...
Man thats a very nice setup you have.
Any more updates? |
Re: Need some engine advice and suggestions...
5 Attachment(s)
Quote:
The new fuel system is installed, 10AN supply/8AN return. I cleaned up the engine compartment, including a new radiator and fan setup (with custom radiator holder). I also had a new tank built with a sump and the proper fuel fittings. Everything seems to be working fairly well, although I'm still trying to get the carb, FPR and BOV dialed in. It's running to rich. I've lowered the pressure on the regulator to 5-5.5 psi, but I think the problem is with the BOV not opening enough at low idle. Any suggestions? I know I need a wideband to help with the tuning, but I want to replace the headers first before installing one. Here's some pictures to catch me/you up, :). |
Re: Need some engine advice and suggestions...
Looking good.
|
Re: Need some engine advice and suggestions...
Where do you have the reference line for the BOV running to?
Is the pump sitting higher then the tank? Looking good. |
Re: Need some engine advice and suggestions...
Quote:
|
Re: Need some engine advice and suggestions...
3 Attachment(s)
Can't believe it's been almost a year since I've updated this thread!!!! Enjoy.
|
Re: Need some engine advice and suggestions...
Still looks great, any updated videos?
|
Re: Need some engine advice and suggestions...
Quote:
|
Re: Need some engine advice and suggestions...
3 Attachment(s)
|
Re: Need some engine advice and suggestions...
Sounds great! :thumbs:
Tell me about those stainless headers. What brand? Do they hang below the frame? |
Re: Need some engine advice and suggestions...
Quote:
http://67-72chevytrucks.com/vboard/s...d.php?t=314836 |
Re: Need some engine advice and suggestions...
Thanks for the reply. I've been keeping an eye on that thread for a while now.
Quote:
|
Re: Need some engine advice and suggestions...
Sounds good and I like the SS headers. I like the muffled exhaust better, just sounds cleaner.
Two things I noticed, your track bar is way off, should be parallel with the ground at ride height. Is your driveshaft too short? I see a lot of the slip yoke in the one picture. |
Re: Need some engine advice and suggestions...
Quote:
I had to move the mounting point down on the track bar (more pics in my build thread) because it was interferring with the aluminum rearend cover. It seems to work well at this location. I'm replacing the 4" drop springs with 6" drop springs so that should help level it out some. As far as the driveshaft, it has approximately 2" that go into the transmission, I assume that is enough? I've got a couple more things that I'm going to do to the suspension that could affect that measurement, when I'm done with that I'll verify that everything is still good. |
Re: Need some engine advice and suggestions...
You should have about an inch left out of the trans, so that could be around 3" in the transmission.
|
Re: Need some engine advice and suggestions...
Rob,
Did you ever do methanol injection? I believe Steve at NewEra Racing engines does this in lieu of an intercooler to reduce detonation. And in turn, run more boost to make huge power. Sorry if it is in the thread somewhere and I missed it, kinda just skimmed through, instead of reading. Paul Baxter |
Re: Need some engine advice and suggestions...
Gorgeous build. Ever take it down the track? (sorry if you posted it and i missed it)
|
All times are GMT -4. The time now is 12:32 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com