Door panel tech tip. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**HO455** · 12-14-2019, 07:09 PM

The door panels in my Burban are covered with fabric and the bottom of the fabric would get wet when it rained. After disassembly I noticed the large amount of tape holding the fabric down (Photo #1) and I assumed that it was somehow catching water and channeling it to the bottom of the panel where it would collect. So I removed the tape, trimmed the fabric and glued it down to the panel. (Photo #2 only shows the bottom done)
After reinstalling I waited for the rains to come and prove my theory. Unfortunately when the rain started one side still was getting soggy. So I pulled it apart again and took a closer look and found the black seal cord was unglued from the door and sagging as the red line in the third photo shows. Once I glued it back in its groove and reassembled it the water stopped collecting in the fabric.
Those clever engineers at GM designed that seal/rubber cord on the door to catch water running down the inside of the door and channel it to one of the two oval holes (Blue arrow) just above the seal where it then would drain back to the inside of the door.
I like fixing water leaks!

**LockDoc** · 12-15-2019, 12:54 AM

-
You know, I've seen those holes but it never dawned on me that was what they were for. Sure makes sense though. I'm bad about not putting the seals back in but I will re-think that practice. Thanks, stuff like this is what makes this board such a great place....

LockDoc

**Ol Blue K20** · 12-15-2019, 11:43 AM

Thanks for the info. I learned something new.

lil hoodlum · 12-16-2019, 01:45 AM

Wow, thanks for the info too. I also learned something new today.

**special-K** · 12-16-2019, 08:56 AM

Are you saying duct tape did not fix that??? I learned something new right there!

Thanks for the helpful tip, I learned to think about that, too, thanks to your thread.

suville · 12-16-2019, 11:29 AM

What are the arm rest/door pulls from

**maverickmk** · 12-16-2019, 11:54 AM

Very good info. I wondered what those little holes were for as well.

Killer Bee · 12-16-2019, 12:41 PM

guess that explains why all four lower screws have to be drilled out of every door panel I remove

good write up, thank you!

**tdangle** · 12-16-2019, 11:24 PM

Quote:

Originally Posted by suville

What are the arm rest/door pulls from

55-66 chevy trucks. I have those in my truck also. The bolt holes line up perfect.

67swb72klb · 12-16-2019, 11:45 PM

I have put plastic visqueen covering the access hole on the door shell to keep the water out.
I believe the factory had some sort of a water shield there as well

**HO455** · 12-17-2019, 02:39 PM

You all are welcome! Just trying to return some knowledge to payback all that I have learned here.
Happy holidays to everyone.

suville · 12-17-2019, 02:48 PM

What arm rest are those from?

**HO455** · 12-17-2019, 03:12 PM

Quote:

Originally Posted by suville

What arm rest are those from?

They are 56-66 GM truck arm rests. And as tdangle said they bolt right on no modification needed. They are the easiest modification I have done on my Burban

https://www.classicindustries.com/sh...ents/armrests/

suville · 12-17-2019, 03:56 PM

Thanks was wondering if they would work. Have a Merry Christmas and a very good 2020

**HO455** · 01-15-2022, 01:14 PM

An additional photo to help show the waters path between the door skin and the door panel.

cj847 · 01-15-2022, 01:48 PM

Excellent info. It is important to note when building any vehicle; anywhere that dirt or water can gather (including simple condensation) it must be vented hopefully on bottom. Most of the common rust on these vehicles could have been prevented or greatly reduced if the vent/drain holes were kept clear.

Even if you look at the parking light lens you will note there is a small gap at the bottom. Even though there is a gasket on the lens it still must have a vent to prevent condensation buildup. This is especially important if you don't live in the desert.

12-15-2019, 11:43 AM	#3
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 15,834	Re: Door panel tech tip. Thanks for the info. I learned something new. __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man

12-16-2019, 01:45 AM	#4
lil hoodlum Registered User Join Date: Oct 2009 Location: Denton, Texas Posts: 1,695	Re: Door panel tech tip. Wow, thanks for the info too. I also learned something new today.

12-16-2019, 08:56 AM	#5
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: Door panel tech tip. Are you saying duct tape did not fix that??? I learned something new right there! Thanks for the helpful tip, I learned to think about that, too, thanks to your thread. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

12-16-2019, 11:29 AM	#6
suville Registered User Join Date: Jun 2003 Location: Mtn. Home, Idaho Posts: 906	Re: Door panel tech tip. *What are the arm rest/door pulls from*

12-16-2019, 11:54 AM	#7
maverickmk Senior Member Join Date: Nov 2019 Location: Cocoa FL Posts: 596	Re: Door panel tech tip. Very good info. I wondered what those little holes were for as well. __________________ Die with memories, not dreams. Not to brag, but I don't need alcohol to make really bad decisions. 1969 GMC Short Step Side

12-14-2019, 07:09 PM	#1
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 10,830	Door panel tech tip. The door panels in my Burban are covered with fabric and the bottom of the fabric would get wet when it rained. After disassembly I noticed the large amount of tape holding the fabric down (Photo #1) and I assumed that it was somehow catching water and channeling it to the bottom of the panel where it would collect. So I removed the tape, trimmed the fabric and glued it down to the panel. (Photo #2 only shows the bottom done) After reinstalling I waited for the rains to come and prove my theory. Unfortunately when the rain started one side still was getting soggy. So I pulled it apart again and took a closer look and found the black seal cord was unglued from the door and sagging as the red line in the third photo shows. Once I glued it back in its groove and reassembled it the water stopped collecting in the fabric. Those clever engineers at GM designed that seal/rubber cord on the door to catch water running down the inside of the door and channel it to one of the two oval holes (Blue arrow) just above the seal where it then would drain back to the inside of the door. I like fixing water leaks! Attached Images __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

12-15-2019, 12:54 AM	#2
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,332	Re: Door panel tech tip. - You know, I've seen those holes but it never dawned on me that was what they were for. Sure makes sense though. I'm bad about not putting the seals back in but I will re-think that practice. Thanks, stuff like this is what makes this board such a great place.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

12-16-2019, 12:41 PM	#8
Killer Bee Registered User Join Date: Jan 2016 Location: Barber City, CA Posts: 4,730	Re: Door panel tech tip. guess that explains why all four lower screws have to be drilled out of every door panel I remove good write up, thank you! __________________ *I started out with nothing - and I still have most of it*

12-16-2019, 11:45 PM	#10
67swb72klb Registered User Join Date: Dec 2010 Location: livingston co.mi Posts: 2,449	Re: Door panel tech tip. I have put plastic visqueen covering the access hole on the door shell to keep the water out. I believe the factory had some sort of a water shield there as well __________________ California 65 GTO---Texas 64 burb 283 ---Oklahoma 67 CST SWB BBW wood bed 327 2004r---New Mexico 72 k10 350 350 auto---Georga 72 short step project

12-17-2019, 02:39 PM	#11
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 10,830	Re: Door panel tech tip. You all are welcome! Just trying to return some knowledge to payback all that I have learned here. Happy holidays to everyone. __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

12-17-2019, 02:48 PM	#12
suville Registered User Join Date: Jun 2003 Location: Mtn. Home, Idaho Posts: 906	Re: Door panel tech tip. *What arm rest are those from?*

12-17-2019, 03:56 PM	#14
suville Registered User Join Date: Jun 2003 Location: Mtn. Home, Idaho Posts: 906	Re: Door panel tech tip. *Thanks was wondering if they would work. Have a Merry Christmas and a very good 2020*

01-15-2022, 01:14 PM	#15
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 10,830	Re: Door panel tech tip. An additional photo to help show the waters path between the door skin and the door panel. Attached Images __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

01-15-2022, 01:48 PM	#16
cj847 Registered User Join Date: Sep 2016 Location: Ft Smith, AR Posts: 543	Re: Door panel tech tip. Excellent info. It is important to note when building any vehicle; anywhere that dirt or water can gather (including simple condensation) it must be vented hopefully on bottom. Most of the common rust on these vehicles could have been prevented or greatly reduced if the vent/drain holes were kept clear. Even if you look at the parking light lens you will note there is a small gap at the bottom. Even though there is a gasket on the lens it still must have a vent to prevent condensation buildup. This is especially important if you don't live in the desert.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.