Project 67 DRGNWGN - 67 Burban!! - Page 36 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**kev2809** · 06-07-2022, 04:57 PM

heres a cool pcm mount i found on ebay..also my home made ground straps. bought a roll on amazon and some size 12 terminals from autozone and pulled the plastic off. threw a little heat shrink after crimping. think they look nice...

FRENCHBLUE72 · 06-07-2022, 09:14 PM

Great to see you still plugging along I'm back here for motivation to finish mine.

BAD1916 · 06-07-2022, 10:10 PM

Nice progress. Those grounds came out looking good. At least lack of good grounds will be checked off on the troubleshooting list if there’s an issue.

**kev2809** · 06-10-2022, 06:03 PM

Quote:

Originally Posted by FRENCHBLUE72

Great to see you still plugging along I'm back here for motivation to finish mine.

thanks for dropping in, interest from you guys make me excited to post progress

Quote:

Originally Posted by BAD1916

Nice progress. Those grounds came out looking good. At least lack of good grounds will be checked off on the troubleshooting list if there’s an issue.

lol, well im hoping i wont run in to anything once the truck is wired but we all know how these builds go.....

i had some time today after work before we head out of town for the weekend. got the obd2 port extended and wired in. mine was a 5 wire plug. purple, green, 2 black, and an orange. i tied the blacks in together, cut the purple (was pin 14), and ran pin 2 (green) to the data wire in the pcm (purple wire). and of course orange to 12v constant. also got the pedal plug extended and pluged to the tac module which will also go under the hood. the random wires hanging through the dash is the tach wire, check engine light wires, tcc wire for the brake switch, and the vss wire for the speedo

**kev2809** · 06-10-2022, 06:10 PM

i bought some generic grommets off amazon and ran the wires through the existing holes in the firewall, this way i will only have to drill one big hole for the engine compartment wires from the main harness that is getting wired next week. also a couple of pics of my little harness plugs i made. one goes from the engine harness into the dash for the obd2 wires and dash wires. the other loom in the background is the pedal wire going from the tac to the pedal inside. last couple of pics is the ground block i made for the back. frame to ground block. body to ground block. and so far fuel pump grounded. when its time for the taillights, the last 2 suds will be for those.

CG · 06-24-2022, 03:20 PM

Quote:

Originally Posted by kev2809

thanks for dropping in, interest from you guys make me excited to post progress

lol, well im hoping i wont run in to anything once the truck is wired but we all know how these builds go.....

i had some time today after work before we head out of town for the weekend. got the obd2 port extended and wired in. mine was a 5 wire plug. purple, green, 2 black, and an orange. i tied the blacks in together, cut the purple (was pin 14), and ran pin 2 (green) to the data wire in the pcm (purple wire). and of course orange to 12v constant. also got the pedal plug extended and pluged to the tac module which will also go under the hood. the random wires hanging through the dash is the tach wire, check engine light wires, tcc wire for the brake switch, and the vss wire for the speedo

Really like your ground straps, nice job. As far as people commenting on your progress dont assume folks arent looking. I think a lot of us check out a ton of builds without commenting.

**3757chevy** · 06-25-2022, 10:40 PM

Quote:

Originally Posted by CG

Really like your ground straps, nice job. As far as people commenting on your progress dont assume folks arent looking. I think a lot of us check out a ton of builds without commenting.

I resemble that remark. I do a lot of looking without saying a word. I make progress without making a comment also.

**kev2809** · 07-02-2022, 09:29 PM

lol, well you guys keep peeking in. i been working on wiring lately, i have a thread over in the electrical section for guidance and for the pros to chime in to make sure im doing it right! hate wiring but im getting a MUCH better understanding of how this stuff works. so far i have the rear wired up (tail lights, reverse lights, grounds), wiper switch, headlight switch, cig lighter, and brake switch done. heading to the beach tomorrow so hopefully on the monday the 4th ill be back at it. looking to get the fuel pump harness done and start tackling my guage cluster...not looking forward to that at all

**kev2809** · 07-21-2022, 07:01 PM

little progress but i got my column back from being rebuilt by Les (70shortfleet). looks amazing! got a few things wired and made a power panel under the dash. the left power strip is wired for 12 volt power. middle 2 post is for battery power. right strip is grounds. just in case i want to add some things, i have an easy spot to tap in. also got my LMC dash pad in...fits great, bought it 10 years ago and has been on my shelf the entire time. i know, im random as hell. im waiting on a harness adapter to come in to get the column wired up. its getting there.

oh! also im getting my cluster together. i went with the s10 speedo mod, camaro tach mod, and mid 80s clock. also the ammeter gauge is actually a battery gauge. still some work to do on it, but its coming along.

BAD1916 · 07-21-2022, 09:06 PM

Cluster looks good. I’ll have to check out the s10 mod. I had not heard of that one yet.

**kev2809** · 07-21-2022, 10:35 PM

ya..lot of work but a good alternative to keeping a stock looking dash if using an electric speedo

http://67-72chevytrucks.com/vboard/s...d.php?t=512751

**LockDoc** · 07-21-2022, 10:54 PM

-
Progress!!! If you do a little each day you will be done before you know it....

I like that electrical setup.

LockDoc
.

**kev2809** · 08-08-2022, 10:32 PM

been working on getting the inner fenders done so i can get the front wired up. bought some trailer fenders, cut to fit and welded them to a strip of plate. they do bolt in so its easy to take out. still need to seam seal the welds and sand and paint them but you get the idea

06-07-2022, 04:57 PM	#876
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! heres a cool pcm mount i found on ebay..also my home made ground straps. bought a roll on amazon and some size 12 terminals from autozone and pulled the plastic off. threw a little heat shrink after crimping. think they look nice... Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

06-07-2022, 09:14 PM	#877
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,523	Re: Project 67 DRGNWGN - 67 Burban!! Great to see you still plugging along I'm back here for motivation to finish mine. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

06-07-2022, 10:10 PM	#878
BAD1916 Registered User Join Date: Oct 2012 Location: VENTURA COUNTY CALIFORNIA Posts: 204	Re: Project 67 DRGNWGN - 67 Burban!! Nice progress. Those grounds came out looking good. At least lack of good grounds will be checked off on the troubleshooting list if there’s an issue.

06-10-2022, 06:10 PM	#880
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! i bought some generic grommets off amazon and ran the wires through the existing holes in the firewall, this way i will only have to drill one big hole for the engine compartment wires from the main harness that is getting wired next week. also a couple of pics of my little harness plugs i made. one goes from the engine harness into the dash for the obd2 wires and dash wires. the other loom in the background is the pedal wire going from the tac to the pedal inside. last couple of pics is the ground block i made for the back. frame to ground block. body to ground block. and so far fuel pump grounded. when its time for the taillights, the last 2 suds will be for those. Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

07-02-2022, 09:29 PM	#883
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! lol, well you guys keep peeking in. i been working on wiring lately, i have a thread over in the electrical section for guidance and for the pros to chime in to make sure im doing it right! hate wiring but im getting a MUCH better understanding of how this stuff works. so far i have the rear wired up (tail lights, reverse lights, grounds), wiper switch, headlight switch, cig lighter, and brake switch done. heading to the beach tomorrow so hopefully on the monday the 4th ill be back at it. looking to get the fuel pump harness done and start tackling my guage cluster...not looking forward to that at all __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

07-21-2022, 07:01 PM	#884
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! little progress but i got my column back from being rebuilt by Les (70shortfleet). looks amazing! got a few things wired and made a power panel under the dash. the left power strip is wired for 12 volt power. middle 2 post is for battery power. right strip is grounds. just in case i want to add some things, i have an easy spot to tap in. also got my LMC dash pad in...fits great, bought it 10 years ago and has been on my shelf the entire time. i know, im random as hell. im waiting on a harness adapter to come in to get the column wired up. its getting there. oh! also im getting my cluster together. i went with the s10 speedo mod, camaro tach mod, and mid 80s clock. also the ammeter gauge is actually a battery gauge. still some work to do on it, but its coming along. Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

07-21-2022, 09:06 PM	#885
BAD1916 Registered User Join Date: Oct 2012 Location: VENTURA COUNTY CALIFORNIA Posts: 204	Re: Project 67 DRGNWGN - 67 Burban!! Cluster looks good. I’ll have to check out the s10 mod. I had not heard of that one yet.

07-21-2022, 10:35 PM	#886
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! ya..lot of work but a good alternative to keeping a stock looking dash if using an electric speedo http://67-72chevytrucks.com/vboard/s...d.php?t=512751 __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

07-21-2022, 10:54 PM	#887
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 23,426	Re: Project 67 DRGNWGN - 67 Burban!! - Progress!!! If you do a little each day you will be done before you know it.... I like that electrical setup. LockDoc . __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

08-08-2022, 10:32 PM	#888
kev2809 low n' slo Join Date: Mar 2009 Location: rosenberg, texas Posts: 4,727	Re: Project 67 DRGNWGN - 67 Burban!! been working on getting the inner fenders done so i can get the front wired up. bought some trailer fenders, cut to fit and welded them to a strip of plate. they do bolt in so its easy to take out. still need to seam seal the welds and sand and paint them but you get the idea Attached Images __________________ 67 1/2 ton Suburban - Project DRGNWGN. Build thread -_--_--_ _________ _--_-_ -/____\|__\|__\__ ,.,,,.,.,,.,\|_O _______ O_]

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.